Yamaha EMX68S Support and Manuals
Get Help and Manuals for this Yamaha item
View All Support Options Below
Free Yamaha EMX68S manuals!
Problems with Yamaha EMX68S?
Ask a Question
Free Yamaha EMX68S manuals!
Problems with Yamaha EMX68S?
Ask a Question
Most Recent Yamaha EMX68S Questions
Yamaha Emx68s Powered Mixer Effects Question
Can you simultaneously use the internal effects, along with an external effects processor which woul...
Can you simultaneously use the internal effects, along with an external effects processor which woul...
(Posted by jdlone 2 years ago)
Yamaha EMX68S Videos
Yamaha EMX68S & 88S
Duration: 1:14
Total Views: 3,653
Duration: 1:14
Total Views: 3,653
Popular Yamaha EMX68S Manual Pages
Owner's Manual - Page 5
... on cell phone usage • Using a cell phone (mobile telephone) near this unit may damage the speakers.
CAUTION
Installation
• Hold the power cord plug when disconnecting it to the
SPEAKERS jack of the connected unit and speakers, and may induce
noise. Blocked ventilation holes are a fire hazard.
• When rack-mounting the unit, allow the unit...
Owner's Manual - Page 7
...20 Example setups 22 As a conference PA system/installed sound
system 22 As a band PA 23 Installing an optional rack mount kit 25 Troubleshooting 26 Specifications 27 General specifications 27 Input specifications 28 Output specifications 28 Dimensions 29 Block and Level diagram 30
EMX88S/EMX68S-Owner's Manual Contents
Introduction 5 Features 5 EMX88S/EMX68S Quick Guide 6 Front and...
Owner's Manual - Page 8
...) to MAIN L-R. EMX88S (EMX68S)
EMX88S/EMX68S-Owner's Manual
Power amp select switch
• This Quick Guide assumes that two main speakers are connected.
Never connect the speakers in the SPEAKERS jack section on the rear panel of the EMX88S/EMX68S. Refer to pages 17-18 for other connections and power amp select switch settings.
• When the power amp select switch is set to the MAIN...
Owner's Manual - Page 10
... YAMAHA SPEAKER PROCESSING switch in stereo.
EMX88S (EMX68S)
Synthesizer, Drum machine, Guitar processor
EMX88S/EMX68S-Owner's Manual
• Be sure to follow the power up sequence specified above to prevent the speakers...set to "0," then press the POWER switch on the EMX88S/EMX68S to the Hi-Z jack of the channel.
You cannot use the Hi-Z jack and the Low-Z jack for the same channel...
Owner's Manual - Page 11
... connected to a channel to be damaged.
EMX88S/EMX68S-Owner's Manual EMX88S (EMX68S)
STEP 4 Applying built-in effects
1 Turn on .
• If you turn off the power to the unit.
2 Turn off the power to all connected devices.
• Be sure to follow the power off sequence specified above to prevent the speakers from being damaged.
• Set the MASTER controls...
Owner's Manual - Page 13
...beside the switch will be set the desired delay time. The mix level of the built-in the MAIN and MONITOR sections. EMX88S/EMX68S-Owner's Manual
This allows you to the speakers and the line level signal... will be remembered even if the power is TAP DELAY. Press the TAP switch several times, and the inter-
B EFFECT RTN control Use this switch to set as the internal effect type, you...
Owner's Manual - Page 14
..., and in digital effect.
EMX88S/EMX68S-Owner's Manual This setting is output from the 2TR IN... indicator allows you to the speakers and the line level signal ...channels 1-6 (EMX88S), 1-4 (EMX68S). K Peak level indicator This indicator allows you do not use these sliders to the MONITOR bus.
s PHANTOM switch, indicator
L
L PHANTOM ON, OFF switch This switch turns the phantom power...
Owner's Manual - Page 15
... a mix of the stereo (MAIN L, R) bus signals is turned on the speakers. EMX88S/EMX68S-Owner's Manual The low range balance when this switch to on / off . Note: Before turning the EMX88S/EMX68S on or off , turn down the MASTER controls of the MONITOR and MAIN section.
M
N
s YAMAHA SPEAKER PROCESSING
O ON/OFF switch This switch enables you can also check...
Owner's Manual - Page 16
... jacks if the PHANTOM switch (control panel L) is on /off in simultaneously for the Low-Z jacks.
Pin connections for channel 8 (EMX88S), 6 (EMX68S).)
EMX88S/EMX68S-Owner's Manual For this reason, devices which do not require phantom power must be used with microphones of output impedance 50- 600Ω. The MIC jacks are balanced, and are compatible with line-level sources...
Owner's Manual - Page 19
...16Ω
8Ω-16Ω 8Ω-16Ω
EMX88S/EMX68S-Owner's Manual
The speaker impedance requirement varies depending on how you connect speakers to MAIN L-R, the signals of outputs. If the power amp select switch is set to MAIN L-R or MAIN (L+R)-MON: • 2-channel connections Connect either setting of the switch, use speakers with an impedance in the range of 400W + 400W...
Owner's Manual - Page 20
... when an 8-ohm speaker is set to MAIN (L+R) BRIDGE:
• Bridge connection Connect only one 8-16 ohm speaker to it when you are using two-channel or two-channel parallel connections. Remove this protective cap only when making a bridge connection.
When using a bridge connection, do not connect a speaker to the BRIDGE jack. VOL
Powered monitor
EMX88S/EMX68S-Owner's Manual s Connecting...
Owner's Manual - Page 22
... the EFFECT controls of each channel of the EMX88S/EMX68S and the MASTER control of the MAIN section are not affected by the effect.
Using the digital effect
The EMX88S/EMX68S has a built-in the order of the monitor section lights up occasionally.
Sending an independent mix to the monitor speakers
1 Set the MONITOR section MASTER control to...
Owner's Manual - Page 24
As a conference PA system/installed sound system
This example shows the EMX88S/EMX68S used simultaneously but their levels cannot be separately adjusted. (Same for channel 8 (EMX88S), 6 (EMX68S))
• If you wish to use the MAIN section 2TR IN control to the MONITOR jack.
Playing back a CD player
1 Turn the power on the CD player, and use an external device such as a conference...
Owner's Manual - Page 27
.../EMX68S-Owner's Manual Use a blank panel with holes for ventilation if you are going to install multiple devices including the unit in a rack, keep a 1U space or more between the devices.
Installing an optional rack mount kit 25
Installing an optional rack mount kit
You can rack-mount the EMX88S/EMX68S using three included screws.
3 Attach the other rack mount bracket in a sealed rack...
Owner's Manual - Page 28
....
EMX88S/EMX68S-Owner's Manual A: The equalizer LOW control for the same channel at the same time? ers.
• If the load impedance (including a short) is too
low, refer to the chapter on connections (page
15) and change the connections so that the
impedance is no signal is turned. Use a speaker with an impedance of this device the problem...
Yamaha EMX68S Reviews
We have not received any reviews for Yamaha yet.