Weider 9400 Support and Manuals
Weider 9400 Videos
Popular Weider 9400 Manual Pages
Instruction Manual - Page 1
...
Please provide the following information when ordering replacement parts:
• The MODEL NUMBER of the product (WEEVSY39530)
• The NAME of the product (WEIDER® PRO 9400 weight system)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of this manual for future reference.
As a manufacturer, we...
Instruction Manual - Page 2
... 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the centre of ICON Health & Fitness, Inc.
2
Leg Lever Cable (75)
3
4 2 1
Swivel Low Cable (72)
3 6
8 1
2 5
4 7
9
Swivel Cable (17) 1
3 5
2 4
27 WEIDER is a registered trademark of this manual.
Instruction Manual - Page 3
... weight system at all instructions before using . If you are exercising, stop immediately and begin cooling down.
16. The cable diagrams on the foot plate when performing an exercise that the cables are properly tightened each cable and the lengths of the cables. Cable Identification Chart
Butterfly Cable (69)-1475mm Swivel Low Cable (72)-5207mm Squat Cable (73)-4425mm Swivel High...
Instruction Manual - Page 4
... manual, please call our Customer Service Department at the end of this you to remove the 90mm Pulley (not
shown) and Pulley Covers (68) from the 50mm Washer (1). The model number is to be found on a decal attached to the weight system (see ORDERING REPLACEMENT PARTS on the back cover of the Leg Lever Cable (75). Replace...
Instruction Manual - Page 5
... them, unless instructed to differences in the centre of soapy water, and masking tape.
The other numbers refer to the 10-pound top weight.
Note: Assembly will attach the cables and pulleys that stage.
Questions?
Cable Assembly-During this manual is the resistance for that connect the weight stations to easily identify parts during each...
Instruction Manual - Page 7
...yet. The weight setting of each part of resistance at each weight station. The Lat Bar (79) can be attached to the Swivel Low Cable (not shown) in...instructions below describe how each weight stack can be attached to the Lat Cable
79
(88) or the Swivel Low Cable (not shown) in the cables or chain as an exercise is touching the Weights. Refer to the exercise guide accompanying this manual...
Instruction Manual - Page 8
... properly installed, they...cables, you will be damaged when heavy weight is used. See the CABLE DIAGRAMS...cables. Before using the weight system, pull each cable a few times to the bottom of this manual for proper cable...cables move smoothly, find and correct the problem.
IMPORTANT: If the cables are closer to make sure that all parts have been properly tightened. See TROUBLESHOOTING...
Instruction Manual - Page 9
... x 85mm
Bolt (94) and an M8 Nylon Locknut (34). Attach a Roller (39) between the indicated set of the holes in the Squat Slider (38) with two M10 x 70mm Carriage Bolts (106), two M10 ...x 65mm Carriage Bolts (110) and two M10 Nylon Locknuts (87). Slide the Top Weight onto the Weight Guides (42).
Assemble the other three Rollers (39) to the Squat Slider (38) in the location shown....
Instruction Manual - Page 10
...Guides (42) to the Butterfly Upright (3) with the Bolt and an M10 Nylon Locknut (87). Open the parts bag labelled "ARM ASSEMBLY." Attach the tethers on the top.
54. Wrap the Squat Cable...two M10 Nylon Locknuts (87).
13. Screw the end of the Pad Tube. Replace the Pin.
Slide the two Knee Pads (19) onto the Pad Tube as ...Weight Pin and set of holes from the top in the Seat Upright (9).
Instruction Manual - Page 11
... and locknuts attaching the pulleys; Locate and open the parts bags labelled "CABLE ASSEMBLY", "PULLEY COVERS", and "PULLEYS."
18
74 ... Locate the Swivel High Cable (74), which is the only
51
remaining cable. Attach two Pulleys and the set of two Plastic Washers...with soapy water. Attach the Swivel Cage (76) to the Cable Identification Chart on the Squat Slider (38) with an M10 x
65mm...
Instruction Manual - Page 14
...87). Wrap the Lat Cable (88) around a 90mm Pulley
29
(78). Attach the end of the Lat Cable (88) inside of the Cable through the Seat Upright (9) and attach it to the second set of holes from the top... the Pulley Plates (63). Small Tab
68 87
69
68 78 100 62
35. Locate the Leg Lever Cable (75), which is 2398mm long and has an eyelet on one end and a threaded pin on the Right...
Instruction Manual - Page 15
... x 50mm Inner Cap (21)
This chart is provided to see if it has been ...part from the PART LIST in the centre of this manual. The hardware for shipping purposes. If you cannot find a part in the parts bags, check to help you identify the small parts used in separate bags. The number in parenthesis below each stage is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable...
Instruction Manual - Page 16
WEEVSY39530 R0803A
12mm Spacer (89)
50mm Washer (1) M10 Washer (91)
16mm Spacer (98) Cable Clip (83)
M8 Washer (90) M6 Washer (97) M4 Washer (120)
M12 Nut (118)
M10 Nylon Locknut (87)
M8 Nylon Locknut (34)
115mm Pulley (...80mm Button Head Bolt (104) M10 x 80mm Bolt (107)
M8 x 85mm Bolt (94) M10 x 85mm Bolt (96) M10 x 95mm Bolt (92) M10 x 165mm Bolt (30) PART IDENTIFICATION CHART-Model No.
Instruction Manual - Page 17
...
Key No. Qty. Specifications are subject to change without notice. PART LIST-Model No. Qty. Description
12... x 20mm Selftapping Screw Butterfly Backrest Seat Swivel Cable M10 x 65mm Bolt Knee Pad Short Pad ...User's Manual Exercise Guide Grease Package
Note: "#" indicates a non-illustrated part. REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL. SAVE THIS PART LIST/EXPLODED...
Weider 9400 Reviews
Do you have an experience with the Weider 9400 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Weider yet.
Earn 750 points for your review!