User Guide
Page 2
...can radiate radio frequency energy and, if not installed and used to operate the equipment. However, there is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. COPYRIGHT & TRADEMARKS Specifications are subject to the following measures: • Reorient or relocate the receiving antenna. &#...8226; Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on , the user is connected. • Consult the dealer or an experienced radio/ TV technician for compliance could void the user's ...
...can radiate radio frequency energy and, if not installed and used to operate the equipment. However, there is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. COPYRIGHT & TRADEMARKS Specifications are subject to the following measures: • Reorient or relocate the receiving antenna. &#...8226; Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on , the user is connected. • Consult the dealer or an experienced radio/ TV technician for compliance could void the user's ...
User Guide
Page 7
...follow the steps: 1) You can place the Switch on a flat desk. 2) Please inspect the Power Adapter carefully and make sure that it is properly connected to a power source. 3) Ensure adequate ventilation space around the switch for dissipating heat and air. ) Note: Please avoid any heavy thing placed on... the switch. 2.2 Power On Powering on the Switch, it will automatically initialize and its LED indicators will respond as follows: 1) All of the Link/Act LED indicators will flash momentarily, which represents a resetting of the system. 2) The Power LED indicator will light all the time. ) Note:...
...follow the steps: 1) You can place the Switch on a flat desk. 2) Please inspect the Power Adapter carefully and make sure that it is properly connected to a power source. 3) Ensure adequate ventilation space around the switch for dissipating heat and air. ) Note: Please avoid any heavy thing placed on... the switch. 2.2 Power On Powering on the Switch, it will automatically initialize and its LED indicators will respond as follows: 1) All of the Link/Act LED indicators will flash momentarily, which represents a resetting of the system. 2) The Power LED indicator will light all the time. ) Note:...
User Guide
Page 8
...located on the rear panel: ¾ Power: The Power socket is equipped with this TL-SF1016D Switch. ¾ Port (1-16): The TL-SF1016D Switch is where you will light green when a device is connected to the corresponding port. Please use the power adapter provided with 16 10/100Mbps Auto-Negociation...up when the Switch powers on the front panel. Chapter 3. It flashes when data is being transmitted or received on the connection. 3.2 Rear Panel Figure 3-2 TL-SF1016D Switch Rear Panel The following parts are located on the front panel. ¾ Power LED: ¾ LEDs (1-16): This ...
...located on the rear panel: ¾ Power: The Power socket is equipped with this TL-SF1016D Switch. ¾ Port (1-16): The TL-SF1016D Switch is where you will light green when a device is connected to the corresponding port. Please use the power adapter provided with 16 10/100Mbps Auto-Negociation...up when the Switch powers on the front panel. Chapter 3. It flashes when data is being transmitted or received on the connection. 3.2 Rear Panel Figure 3-2 TL-SF1016D Switch Rear Panel The following parts are located on the front panel. ¾ Power LED: ¾ LEDs (1-16): This ...
User Guide
Page 10
The Power LED is not lit Check to see if the power cord is connected to see if the cable connectors are firmly plugged into the Switch and the device, and verify the connected device is turned on and working well. The Link/Act LED is not lit when a device is connected to the corresponding port Check to the Switch properly, and make sure the power source is not longer than 100 meters (328 feet). 5 Make sure the cable is ON. 2. Appendix B: Troubleshooting 1.
The Power LED is not lit Check to see if the power cord is connected to see if the cable connectors are firmly plugged into the Switch and the device, and verify the connected device is turned on and working well. The Link/Act LED is not lit when a device is connected to the corresponding port Check to the Switch properly, and make sure the power source is not longer than 100 meters (328 feet). 5 Make sure the cable is ON. 2. Appendix B: Troubleshooting 1.
