Quick Reference Guide
Page 18
a Press the I/1 (on the computer connected to only the external monitor. 1 2 On/Stand by Power COVER ENU AC IN 3 INPUT Input A Video S-Video 4 F7 or Fx and Fn 6 Projecting Projecting Before connecting the equipment, plug the AC power cord into a wall outlet. b Turn on /standby) key. d When the computer is connected, set it to output the video signal to the projector. c Press the INPUT key to select the input source.
a Press the I/1 (on the computer connected to only the external monitor. 1 2 On/Stand by Power COVER ENU AC IN 3 INPUT Input A Video S-Video 4 F7 or Fx and Fn 6 Projecting Projecting Before connecting the equipment, plug the AC power cord into a wall outlet. b Turn on /standby) key. d When the computer is connected, set it to output the video signal to the projector. c Press the INPUT key to select the input source.
Quick Reference Guide
Page 19
c Unplug the AC power cord from the wall outlet after the I/1 key is pressed to turn off the Power a Press the I /1 (on /standby) key. FOCUS + Turning off the power and the ON/STANDBY indicator changes to operate for a short time even after the fan has stopped running and the ON/STANDBY indicator has lit .... ZOOM + 3 AUTO FOCUS TILT or - Notes The internal circuitry of the Off & Go function may cause the fan to continue to red. 1 3 2 Projecting 7 Adjusting the Projector a Adjust the position of the picture.
c Unplug the AC power cord from the wall outlet after the I/1 key is pressed to turn off the Power a Press the I /1 (on /standby) key. FOCUS + Turning off the power and the ON/STANDBY indicator changes to operate for a short time even after the fan has stopped running and the ON/STANDBY indicator has lit .... ZOOM + 3 AUTO FOCUS TILT or - Notes The internal circuitry of the Off & Go function may cause the fan to continue to red. 1 3 2 Projecting 7 Adjusting the Projector a Adjust the position of the picture.
Quick Reference Guide
Page 20
...an hour for the lamp to cool. Note When replacing the lamp after the projector is a consumable product. Use an LMP-C163 Projector Lamp as a light source is turned off the projector, and disconnect the AC power cord from the AC outlet. Notes • If the lamp breaks, contact your finger. If ... may scatter, causing injury. 1 Turn off with the Phillips screwdriver (a). Replacing the Lamp The lamp used as the replacement lamp. Turn the projector over so you may be burned or injured. • When removing the lamp, make sure it is stable after turning it over. 3 Open...
...an hour for the lamp to cool. Note When replacing the lamp after the projector is a consumable product. Use an LMP-C163 Projector Lamp as a light source is turned off the projector, and disconnect the AC power cord from the AC outlet. Notes • If the lamp breaks, contact your finger. If ... may scatter, causing injury. 1 Turn off with the Phillips screwdriver (a). Replacing the Lamp The lamp used as the replacement lamp. Turn the projector over so you may be burned or injured. • When removing the lamp, make sure it is stable after turning it over. 3 Open...
Quick Reference Guide
Page 23
If the problem persists, consult with the power of the projector turned on. c Attach the air filter cover securely. The AC power cord was unplugged with qualified Sony personnel. If your computer, for about 45 seconds before turning on the LCD panel. For details, refer to the computer's operating instructions supplied with the ?/1 key at a short interval. c Change...
If the problem persists, consult with the power of the projector turned on. c Attach the air filter cover securely. The AC power cord was unplugged with qualified Sony personnel. If your computer, for about 45 seconds before turning on the LCD panel. For details, refer to the computer's operating instructions supplied with the ?/1 key at a short interval. c Change...
Quick Reference Guide
Page 24
...cover securely. Lights in power saving mode. Flashes in red when a AC power cord is turned on . "Dot Phase" on the power again, or replace the lamp. Lights up when temperature inside the projector becomes unusually high. ...Flashes when the lamp cover is broken. c Leave the projector for 45 seconds to operate the projector. 12 Troubleshooting Flashes when the fan is not secured firmly. Consult with qualified Sony...
...cover securely. Lights in power saving mode. Flashes in red when a AC power cord is turned on . "Dot Phase" on the power again, or replace the lamp. Lights up when temperature inside the projector becomes unusually high. ...Flashes when the lamp cover is broken. c Leave the projector for 45 seconds to operate the projector. 12 Troubleshooting Flashes when the fan is not secured firmly. Consult with qualified Sony...
Quick Reference Guide
Page 25
... system 3 LCD panels, 1 lens, projection system LCD panel VPL-CX21: 0.63-inch XGA panel, approximately 2,360,000 pixels (786,432 pixels × 3) VPL-CS21: 0.63-inch SVGA panel, approximately 1,440,000 pixels (480,000 pixels × 3) Lens 1.2 times zoom lens (powered) f 18...adaptor (1) (1-830-658-XX) Carrying case (1) AC power cord (1) Operating Instructions (CD-ROM) (1) Quick Reference Manual (1) Safety Regulations (1) Security Label (1) Air filter (for replacement) Main Specifications 13 Optional accessories Projector Lamp LMP-C163 (for replacement) (1) Design and...
... system 3 LCD panels, 1 lens, projection system LCD panel VPL-CX21: 0.63-inch XGA panel, approximately 2,360,000 pixels (786,432 pixels × 3) VPL-CS21: 0.63-inch SVGA panel, approximately 1,440,000 pixels (480,000 pixels × 3) Lens 1.2 times zoom lens (powered) f 18...adaptor (1) (1-830-658-XX) Carrying case (1) AC power cord (1) Operating Instructions (CD-ROM) (1) Quick Reference Manual (1) Safety Regulations (1) Security Label (1) Air filter (for replacement) Main Specifications 13 Optional accessories Projector Lamp LMP-C163 (for replacement) (1) Design and...