Singer Futura Quartet SEQS-6000 Support and Manuals
Get Help and Manuals for this Singer item
View All Support Options Below
Free Singer Futura Quartet SEQS-6000 manuals!
Problems with Singer Futura Quartet SEQS-6000?
Ask a Question
Free Singer Futura Quartet SEQS-6000 manuals!
Problems with Singer Futura Quartet SEQS-6000?
Ask a Question
Most Recent Singer Futura Quartet SEQS-6000 Questions
Can You Use A Macbook Air To Install Software?
(Posted by athomas010802 11 months ago)
Machine Stops After 5 Stitches. Error Message 0.1. Nothing In Bobbin Area. Pleas
machine stitches 5 stitches and stops with error code 0.1. Nothing in bobbin ca
machine stitches 5 stitches and stops with error code 0.1. Nothing in bobbin ca
(Posted by barfar224 2 years ago)
Seqs 6000
can't seem to connect to laptop. error message says check that usb cable is connected and power swit...
can't seem to connect to laptop. error message says check that usb cable is connected and power swit...
(Posted by reneewindell 8 years ago)
Skipping Or Loose Bottom Stitch
the underside of the straight stitch is skipping leaving loose stitch
the underside of the straight stitch is skipping leaving loose stitch
(Posted by cougar6808 9 years ago)
Popular Singer Futura Quartet SEQS-6000 Manual Pages
Instruction Manual - Page 2
... nearest authorized dealer or service center for its Affiliates. This appliance complies with this sewing machine if it has a damaged cord or plug, if it has been dropped or damaged, or dropped into water. SINGER and FUTURA QUARTET are being administered." 10.
Always unplug this manual. Return the sewing machine to install the proper outlet. To...
Instruction Manual - Page 3
...software 37 - 38 Operation switches when embroidery unit is attached 39 Operation switches, Thread tension control Troubleshooting... 2 Accessories 3 Setting up your...hoop 33 Using fabric and stabilizer 34 - 35 Preparing the machine before installing the hoop 36 Attaching and removing embroidery hoop 36 Installation...Futura Multi hoop 44 - 47 Helpful messages when embroidering 48
4.
Instruction Manual - Page 4
... wheel
14. Hoop mounting plate
41
46
46. 1. GETTING TO KNOW YOUR MACHINE
MACHINE IDENTIFICATION
2
1
8
1. Thread tension control
3
9
4. Extension table (Accessory box)
5
10
8. Feed dog control
18. Pre-tension guide
2. Needle plate
26
32. Horizontal spool pin 12. Buttonhole lever
11
17. Twin thread guide
22. Connector 41. Instruction manual
42
42...
Instruction Manual - Page 5
... sure they are accessed via your embroidery machine. ACCESSORIES
FOR SEWING MACHINE
1. Spool pin felt discs
5. Spool pin cap (small)
7. When purchasing additional bobbins, be used for the majority of your
sewing. Vinyl bag 20. To install the FUTURA software, refer to your computer by installing the FUTURA software. Screwdriver (small)
12. Buttonhole opener/Brush
9. Button...
Instruction Manual - Page 6
...into the cord socket (1) and your machine the first time.
When servicing the machine, or when changing needles or lights, etc., the machine... from the power supply.
Power line cord Foot control
XL-550-P04-1.eps
Power/light switch "OFF"
Power/light switch...as illustrated. Power line cord/FOOT CONTROL
Connect the plug of thread. Set power/light switch at "OFF"
machine socket
2 1
Pin
3
...
Instruction Manual - Page 10
Make sure that
the machine be set for straight stitch (in operation or the threading hook may be broken. Pull thread loop away from needle hole after hooking the thread through the thread guide on the needle bar and pull it in place. Threading hook
2
Twin thread guide
A B
3
Thread cutter/holder
4
Threading lever
8 Hook...
Instruction Manual - Page 15
... twin needle sewing can be activated, if it will automatically sew at the Auto / Default Position. *Manual settings Once you have determined the Auto / Default position you can manually change the length, width or straight stitch needle postition according to the Control will light in orange without blinking and a beep will sound indicating...
Instruction Manual - Page 16
... that the machine malfunctions.
SPEED CONTROL LEVER
Sliding the lever sets desired sewing speed. TACKING STITCH MODE BUTTON
Push this button ...set at its up -stop position with
4
upper LED lamp lit.
3. START/STOP BUTTON
When the Start/Stop button is pushed, the machine starts slowly, and when the button is operating.
Flashing red light indicates a problem or an error...
Instruction Manual - Page 21
... never appear on the weight of stabilizer to help avoid stitches puckering the fabric. is set automatically when pattern (No. 03) is the selection range when setting the value manually. SATIN STITCH
This is about 5 mm. ZIGZAG STITCHING
SETTINGS :Presser foot - The stitch length is 2 mm and the stitch width is a closely spaced stitch...
Instruction Manual - Page 22
...- First finish the raw edge. NOTE: For a narrower or wider blind hem, first manually adjust the length and width controls to sew blind hem.
NOTE: It takes practice to...fold. Place the fabric under on fine fabrics or overcasting it does
not, adjust the guide (B) on medium to the left. BLIND STITCH
SETTINGS :Presser foot - Then turn the hem up the required depth, press and pin ...
Instruction Manual - Page 39
...-ROM
Simply click on "Next" to as "installation procedure". In most personal computers the default drive setting for a CD-ROM drive is refered to continue.
37
INSTALLATION OF SOFTWARE
In order to start using the software on your PC you may start the installation procedure manually by -step installation of the software begins with terms given in your PC.
Instruction Manual - Page 40
... during the installation set-up protocol. CORRECT START-UP PROCEDURE WHEN EMBROIDERING
The following steps must be stored. Turn on the hard disk. Double click on the Futura Icon on "Cancel".
Next attach the embroidery unit to your sewing machine and connect the USB cable between your desktop to open the Futura software. Make sure...
Instruction Manual - Page 41
...61661; Red light indicates machine is operating.
Flashing red light indicates a problem or an error. * Flashing for embroidery to loosen thread tension. To stop button is pushed, ... hoop will stop button (For embroidery only)
THREAD TENSION CONTROL
Set it is already in Machine navigator, before
sending the design to the machine.
NOTE: When sewing designs created by the software ...
Instruction Manual - Page 43
... 7 "Setting the Top Thread".) Placing the small net that is unwinding properly.
41 HELPFUL INFORMATION FOR EMBROIDERING WITH FUTURA
1. Press...hoop will move back one stitch at a time.
Restart the embroidery machine and continue embroidering. Computer screen says thread is broken, machine lights are missing
If the embroidery machine detects that the thread is supplied with the accessories...
Instruction Manual - Page 59
... left needle's eye. Sew your machine.
* The pintuck foot is an optional accessory.
* The edge guide (quilting bar) is best utilized when paired with both threads. For wider spaced ...thread manually.
4. Do not use the machine's automatic needle threader; For threading, follow the machine's thread path with the general purpose foot or the straight stitch foot (optional accessory). The...
Singer Futura Quartet SEQS-6000 Reviews
We have not received any reviews for Singer yet.