CD-SW300 Operation Manual
Page 3
... protect it from the type of the product and to be operated only from overheating, and these openings must not be retained for replacement or resetting of the polarized plug. This product is a safety feature. If you are provided for venti- ample, near water - in the operating instructions should be equipped.... This is operated. 2 Retain Instructions - The product may cause hazards. 7 Water and Moisture - This plug will fit into a grounding-type power outlet. IMPORTANT SAFETY INSTRUCTIONS CD-SW300 Important Instruction 1 Read Instructions -
... protect it from the type of the product and to be operated only from overheating, and these openings must not be retained for replacement or resetting of the polarized plug. This product is a safety feature. If you are provided for venti- ample, near water - in the operating instructions should be equipped.... This is operated. 2 Retain Instructions - The product may cause hazards. 7 Water and Moisture - This plug will fit into a grounding-type power outlet. IMPORTANT SAFETY INSTRUCTIONS CD-SW300 Important Instruction 1 Read Instructions -
CD-SW300 Operation Manual
Page 16
... 12-hour or 24- If incorrect, readjust the clock as follows. PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 12:00 - CD-SW300 Setting the clock (Remote control only) 5 Press the or button to advance the time by 1 minute. Basic Operation In this example, the clock is on.... Within 10 seconds, press the or button to se- Hold it down to change the 12-hour or 24-hour display: 1 Clear all the memory (reset)" on page 41 for about 10 seconds.
... 12-hour or 24- If incorrect, readjust the clock as follows. PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 12:00 - CD-SW300 Setting the clock (Remote control only) 5 Press the or button to advance the time by 1 minute. Basic Operation In this example, the clock is on.... Within 10 seconds, press the or button to se- Hold it down to change the 12-hour or 24-hour display: 1 Clear all the memory (reset)" on page 41 for about 10 seconds.
CD-SW300 Operation Manual
Page 39
...sure your authorized SHARP dealer or service center. When a button is heard. No sound is pressed, the unit does not respond. Possible cause Is the disc loaded upside down? Is the disc distorted or scratched? References CD player Symptom Playback does not start. Troubleshooting chart CD-SW300 Many potential problems ...a track. General Symptom The clock is 32 ohms. Plugging in or unplugging the headphones, reduce the volume. If the unit still malfunctions, reset it. (Refer to page 41.) Is the volume level set to the power standby mode and then turn it back on. Are the ...
...sure your authorized SHARP dealer or service center. When a button is heard. No sound is pressed, the unit does not respond. Possible cause Is the disc loaded upside down? Is the disc distorted or scratched? References CD player Symptom Playback does not start. Troubleshooting chart CD-SW300 Many potential problems ...a track. General Symptom The clock is 32 ohms. Plugging in or unplugging the headphones, reduce the volume. If the unit still malfunctions, reset it. (Refer to page 41.) Is the volume level set to the power standby mode and then turn it back on. Are the ...
CD-SW300 Operation Manual
Page 41
...and turn the power on. Before transporting the unit Remove all the memory (reset) 1 Press the ON/STAND-BY button to an accumulation of dirt on the CDs can damage the unit. Make sure there is no CD in the unit, and then turn the power on either side of compact ...dry cloth, wiping straight out from which signals are fairly resistant to damage, however mistracking can occur due to enter the power stand-by mode. CD-SW300 If trouble occurs When this surface. Note: If neither operation above restores the unit, clear all data stored in memory including clock, timer settings, ...
...and turn the power on. Before transporting the unit Remove all the memory (reset) 1 Press the ON/STAND-BY button to an accumulation of dirt on the CDs can damage the unit. Make sure there is no CD in the unit, and then turn the power on either side of compact ...dry cloth, wiping straight out from which signals are fairly resistant to damage, however mistracking can occur due to enter the power stand-by mode. CD-SW300 If trouble occurs When this surface. Note: If neither operation above restores the unit, clear all data stored in memory including clock, timer settings, ...