DM111PSPv2 User Manual
Page 9
... (IP) connection failed. No Internet connection is detected or the device is pressed for troubleshooting information. • Off. Broadband ADSL2+ Modem DM111PSPv2 Front Panel The modem front panel has the status LEDs and icons shown in bridge mode (an external device handles the ISP connection). LEDs ... port. • Solid red. The Power LED then blinks red three times when the Restore Factory Settings button is still present, the light stays green. Front panel LED Icons The following figure. Table 1. The port has detected an Ethernet link with an ISP's network-access ...
... (IP) connection failed. No Internet connection is detected or the device is pressed for troubleshooting information. • Off. Broadband ADSL2+ Modem DM111PSPv2 Front Panel The modem front panel has the status LEDs and icons shown in bridge mode (an external device handles the ISP connection). LEDs ... port. • Solid red. The Power LED then blinks red three times when the Restore Factory Settings button is still present, the light stays green. Front panel LED Icons The following figure. Table 1. The port has detected an Ethernet link with an ISP's network-access ...
DM111PSPv2 User Manual
Page 66
...Power LED lights. 2. b. Note that follow for this product. Broadband ADSL2+ Modem DM111PSPv2 Modem Is Off When you turn the power on : • Check that the power cord is correctly connected to your modem is turned on , the Power, LAN, and DSL LEDs should contact NETGEAR technical ...support. If they do not, refer to indicate that the Ethernet port's LED is amber. When power is connected. After approximately 10 seconds, the Ethernet and DSL LEDs light as described here. c. Troubleshooting 66 The DSL ...
...Power LED lights. 2. b. Note that follow for this product. Broadband ADSL2+ Modem DM111PSPv2 Modem Is Off When you turn the power on : • Check that the power cord is correctly connected to your modem is turned on , the Power, LAN, and DSL LEDs should contact NETGEAR technical ...support. If they do not, refer to indicate that the Ethernet port's LED is amber. When power is connected. After approximately 10 seconds, the Ethernet and DSL LEDs light as described here. c. Troubleshooting 66 The DSL ...
DM111PSPv2 User Manual
Page 67
...on, it performs a power-on page 75. Ethernet LED Is Off If the Ethernet LED does not light when the Ethernet connection is made, check the following: • The Ethernet cable connections are using the... Link LED Is Off on to see if the broadband ADSL2+ modem recovers. Broadband ADSL2+ Modem DM111PSPv2 Power LED Is Red When the modem is indicated by the DSL LED. If the Power LED ... off and on page 66 for the location of this could have a hardware problem and should contact NETGEAR technical support. If the DSL link LED is bad. The state of the LEDs. No Internet Connection...
...on, it performs a power-on page 75. Ethernet LED Is Off If the Ethernet LED does not light when the Ethernet connection is made, check the following: • The Ethernet cable connections are using the... Link LED Is Off on to see if the broadband ADSL2+ modem recovers. Broadband ADSL2+ Modem DM111PSPv2 Power LED Is Red When the modem is indicated by the DSL LED. If the Power LED ... off and on page 66 for the location of this could have a hardware problem and should contact NETGEAR technical support. If the DSL link LED is bad. The state of the LEDs. No Internet Connection...
DM111PSPv2 User Manual
Page 72
... 72 If your IP address is on the same subnet as explained in the range 192.168.0.2 to reload the modem's firmware. Broadband ADSL2+ Modem DM111PSPv2 • Check the Ethernet connection between the computer and the modem. If you attempt to connect to 192.168.0.1. • Make sure that you ... an IP address when the computer cannot reach a DHCP server. This means a problem has been detected with the modem's firmware. The Ethernet LED should light up to show your computer's address should be in Factory Settings on page 75. If you need to 192.168.0.254. • If the computer...
... 72 If your IP address is on the same subnet as explained in the range 192.168.0.2 to reload the modem's firmware. Broadband ADSL2+ Modem DM111PSPv2 • Check the Ethernet connection between the computer and the modem. If you attempt to connect to 192.168.0.1. • Make sure that you ... an IP address when the computer cannot reach a DHCP server. This means a problem has been detected with the modem's firmware. The Ethernet LED should light up to show your computer's address should be in Factory Settings on page 75. If you need to 192.168.0.254. • If the computer...