Instruction Manual
Page 3
... Code Setup 62 TV Setup (Function of PAL TV type) 63 RDS Setup 64 AMP Control 64 Setup Memory 65 EXT SW Setup 66 Accessories 74 Installation Procedure 75 Connection 76 System Connection 78 Optional Accessory Connection 79 Installation 81 Specifications 82 English 3 Troubleshooting 72 Background Delete Background Select 58 58 Help? Hands...
... Code Setup 62 TV Setup (Function of PAL TV type) 63 RDS Setup 64 AMP Control 64 Setup Memory 65 EXT SW Setup 66 Accessories 74 Installation Procedure 75 Connection 76 System Connection 78 Optional Accessory Connection 79 Installation 81 Specifications 82 English 3 Troubleshooting 72 Background Delete Background Select 58 58 Help? Hands...
Instruction Manual
Page 6
...this unit. The functions you connect them incorrectly. 6 KOS-V500 About CD disc changers connected to this unit Kenwood disc changers released in 1998 or later can be connected to this unit. Refer to the "N" position for the applicable Kenwood disc changers. Connecting unsupported disc changerss to this product...machine, take the following precautions: • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. If you use the wrong screws, you are driving for ...
...this unit. The functions you connect them incorrectly. 6 KOS-V500 About CD disc changers connected to this unit Kenwood disc changers released in 1998 or later can be connected to this unit. Refer to the "N" position for the applicable Kenwood disc changers. Connecting unsupported disc changerss to this product...machine, take the following precautions: • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. If you use the wrong screws, you are driving for ...
Instruction Manual
Page 7
... with Dock connector using an optional accessory iPod connection cable (KCA-iP300V ). TV tuner that can be connected to this unit • KTC-V300P Navigation units that can ... version is pressed. • Remove the USB device before pressing the Reset button. Controllable iPod iPod nano iPod nano second generation iPod with video Software version iPod nano software ...button with the USB device installed can damage the data contained in the illustrations may be inapplicable. Notes • If you experience problems during installation, consult your Kenwood dealer. • When...
... with Dock connector using an optional accessory iPod connection cable (KCA-iP300V ). TV tuner that can be connected to this unit • KTC-V300P Navigation units that can ... version is pressed. • Remove the USB device before pressing the Reset button. Controllable iPod iPod nano iPod nano second generation iPod with video Software version iPod nano software ...button with the USB device installed can damage the data contained in the illustrations may be inapplicable. Notes • If you experience problems during installation, consult your Kenwood dealer. • When...
Instruction Manual
Page 9
We shall have one of the following extensions: jpg, jpeg, jpe About USB device • Install the USB device in the place where it will not prevent you from driving your vehicle properly. • You cannot connect a USB device via a USB ...(H) pixels ⁄ • Enlarges and reduces images up English 9 Extensions Picture files must have no compensation for AV-IN, Inner AMP, and Tuner source when the unit is installed or the reset button is pressed. 1 Start system start up setting You need to go through the setup for any damage arising out...
We shall have one of the following extensions: jpg, jpeg, jpe About USB device • Install the USB device in the place where it will not prevent you from driving your vehicle properly. • You cannot connect a USB device via a USB ...(H) pixels ⁄ • Enlarges and reduces images up English 9 Extensions Picture files must have no compensation for AV-IN, Inner AMP, and Tuner source when the unit is installed or the reset button is pressed. 1 Start system start up setting You need to go through the setup for any damage arising out...
Instruction Manual
Page 11
... not move during braking or other operations. DVD mode Switch to this mode when playing DVD player unit. Battery installation Use two "AAA"/"R03"-size batteries. A dangerous situation could result, if the Remote Controller falls down and gets wedged under the pedals while driving. • Do not place the battery near an...
... not move during braking or other operations. DVD mode Switch to this mode when playing DVD player unit. Battery installation Use two "AAA"/"R03"-size batteries. A dangerous situation could result, if the Remote Controller falls down and gets wedged under the pedals while driving. • Do not place the battery near an...
Instruction Manual
Page 75
... rating. • Insulate unconnected wires with the ignition key. battery. 8. To prevent a short circuit, do not mix front and rear). Installation Procedure Installation Procedure 1. If you share the - connector to a power source that in the car. • When only two speakers are working properly.... • Mount the unit so that the mounting angle is installed, check whether the brake lamps, blinkers, wipers, etc. Make the proper input and output wire connections for each unit. 3. Therefore, ...
... rating. • Insulate unconnected wires with the ignition key. battery. 8. To prevent a short circuit, do not mix front and rear). Installation Procedure Installation Procedure 1. If you share the - connector to a power source that in the car. • When only two speakers are working properly.... • Mount the unit so that the mounting angle is installed, check whether the brake lamps, blinkers, wipers, etc. Make the proper input and output wire connections for each unit. 3. Therefore, ...
Instruction Manual
Page 81
... it is exposed to fix A/V controller Unit onto an audio board or another. Install the Remote control sensor temporarily and verify that do not obstruct driving. Installation for Remote control sensor 1 Wipe off . • Do not install the Remote control sensor in the specified place with the doublesided adhesive tape. Installation Installation for A/V controller Unit Use Tapping screws (Accessory7) to...
... it is exposed to fix A/V controller Unit onto an audio board or another. Install the Remote control sensor temporarily and verify that do not obstruct driving. Installation for Remote control sensor 1 Wipe off . • Do not install the Remote control sensor in the specified place with the doublesided adhesive tape. Installation Installation for A/V controller Unit Use Tapping screws (Accessory7) to...
Instruction Manual
Page 83
... : 1 kHz ± 8 dB Treble : 10 kHz ± 8 dB External SW Maximum Power Supply Current : 500mA General Operating voltage : 14.4 V (11 - 16 V allowable) Current Consumption : 15 A Installation Size (W × H × D) : 319.2mm×41.0mm×232.0mm Operational Temperature Range : -10 °C - +60 °C Storage Temperature Range : -20 °C - +85 °...
... : 1 kHz ± 8 dB Treble : 10 kHz ± 8 dB External SW Maximum Power Supply Current : 500mA General Operating voltage : 14.4 V (11 - 16 V allowable) Current Consumption : 15 A Installation Size (W × H × D) : 319.2mm×41.0mm×232.0mm Operational Temperature Range : -10 °C - +60 °C Storage Temperature Range : -20 °C - +85 °...