Icom IC-T70A / E Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-T70A / E manuals!
Problems with Icom IC-T70A / E?
Ask a Question
Free Icom IC-T70A / E manuals!
Problems with Icom IC-T70A / E?
Ask a Question
Popular Icom IC-T70A / E Manual Pages
Instruction Manual - Page 1
... THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INSTRUCTION MANUAL
VHF/UHF DUAL BAND FM...
Instruction Manual - Page 2
The ICT70A/T70E vhf/uhf dual band fm transceiver is designed and build with years of trouble-free operation. With proper care, this fine Icom product.
No risk of your IC-T70A/T70E.
EXPLICIT DEFINITIONS
WORD R DANGER!
FEATURES
❍ Dust-protection/Splash-resistant construction (IP54*)
*Only when the battery pack/case, antenna and jack cover are attached.
❍...
Instruction Manual - Page 16
... of these conditions occur, contact your Icom dealer or distributor.
• R WARNING! Do not use the battery if it dry before using clean water, any part of the battery does not show cracks...in the battery, such as could occur near fires or stoves, inside the battery gets in this instruction manual.
• R DANGER! DO NOT expose the battery to wipe it has been severely impacted or...
Instruction Manual - Page 24
...loose squelch (for weak signals) and "LEVEL9" is tight squelch (for details. or to open setting.
[DIAL]
■ Monitor function
This function is used to listen to monitor the operating frequency. .... • "OPEn" indicates the continuously open the squelch manually even when mute functions such as the tone squelch are in the Initial set to a 'sticky' operation in use.
➥ Push...
Instruction Manual - Page 26
... step 19
[DIAL] changes the frequency according to select the desired tuning step. w P ush [BAND] to enter the Set mode. 4 BASIC OPERATION
■ Setting the tuning step
The tuning step can be selected for the IC-T70A/T70E.
• 5.0 kHz • 10.0 kHz • 12.5 kHz • 15.0 kHz • 20.0 kHz • 25.0 kHz...
Instruction Manual - Page 29
...] to suit your op- 2
erating requirements.
e Set the receive frequency. (p. 20) r Set the squelch level. (p. 17)
• While continuing to push [MONI](BAND), rotate [DIAL]. • The first click of interference to other stations, and will conserve battery power.
4
➥ P ush [H/M/L] to open the squelch manually. Low output power during short-range 3
communications...
Instruction Manual - Page 33
... repeater function has priority over the manual duplex
setting. If the transmit frequency changes after setting, the 3
auto repeater function may have changed the duplex setting. 4
Turn the auto repeater function OFF to enter the Set mode. ON 144.700 MHz 145.300 MHz
19
26 The function can be set the frequency offset. to select...
Instruction Manual - Page 36
...T70 cloning software... during repairs.
quency or DTCS code with ... can be programmed into memory channels:
•...setting (p. 46) • Memory bank (p. 32) • Memory name (p. 34) • Tuning step (p. 19) • Output power (p. 22)
■ Selecting a call channel
q P ush [V/M/C] to a bank. version transceiver. 6 MEMORY/CALL CHANNELS
■ General description
The IC-T70A/T70E...
Instruction Manual - Page 39
... mode. 32 to assign the 18
channel to the bank.
• Return to select a desired memory channel. to Z). 6 MEMORY/CALL CHANNELS
■ Memory bank setting
The IC-T70A/T70E has a total of 26 banks (A to enter the select memory write mode. • 1 short and 1 long beep sounds. • The " " icon and memory channel...
Instruction Manual - Page 54
.... w R otate [DIAL] to manually resume the scan. pears.
nal. • "HOLd" : Scan pauses on the received signal accord-
D Scan resume timer
The scan restarts after the signal disap- pears.
• "1"-"5" : Scan restarts 1-5 seconds after the signal disappears, depending on the scan pause time.
7 SCAN OPERATION
■ Scan resume setting
D Scan pause timer...
Instruction Manual - Page 73
...transmit a DTMF code sequence manually.
• [0]-[9], [A](SET), [B](BAND), [C](H/M/L), [D](V/M/C), [M](.) or
5
[#] sends "0"-"9," "A," "B," "C," "D," "M" or "#."
6
7
[PTT]
8
9
10
e R otate [VOL] to select a desired DTMF key setting. • kEy : T ransmits the appropriate DTMF code assigned to the pushed key. (default) • mEm : T ransmits the programmed DTMF code sequence in...
Instruction Manual - Page 78
... be changed .
• The detected tone is cancelled before the transceiver detects the tone or code, the set mode contents are programmed with the scanning tone frequency in scan pause timer (p. 47) when a tone frequency or DTCS code is detected. • The decoded tone frequency is used for the repeater tone frequency when any...
Instruction Manual - Page 81
...when you want to copy all of the programmed contents from one IC-T70A/T70E to another. • An optional ... p u s h [V/M/C], push and hold [ ] for 1 sec.
OPC-474
to the [SP] jack
to turn power OFF.
5
6
7
The optional CS-T70 CLONING SOFTWARE is required. to enter the cloning mode.
• "CLOnE m" appears.
1
e Push [PTT] on the "master" transceiver.
2
• "CL Out m" ...
Instruction Manual - Page 83
... a service center.
1
PROBLEM
POSSIBLE CAUSE
Transceiver does not turn • The battery is exhausted. p. 2
76 pp. 2, 11-14
• Check the battery polarity. p. 62
• The heat protection is activated, and "Hot" is reversed. p. 18
start .
• Only one or no memory channel has been pro- • Program 2 or more memory channels.
11 TROUBLESHOOTING...
Instruction Manual - Page 86
... cigarette lighter cable Allows charging of the battery packs through a 12 V cigarette lighter socket. Icom is not responsible for the destruction or damage to an Icom ...cigarette lighter cable with noise filter • CP-19R cigarette lighter cable with CS-T70 (cloning software).
• CS-T70 cloning software Provides quick and easy programming of such settings as memory channels and Set...
Icom IC-T70A / E Reviews
We have not received any reviews for Icom yet.