Icom HM162B Support and Manuals
Popular Icom HM162B Manual Pages
Instruction Manual - Page 1
...COMMANDMIC IIITM is input manually.
q Connection cable (OPC-1540*: 6 m; 20 ft 1
w Mounting base 1
e Connector cap 1
r Microphone hanger 1
t Screws (M3 × 16;
"[VOL]" appears when [SELECTOR] as these instructions...position data is in the 'Set up to approx. 10 V ... read the connected transceiver's instruction manual carefully before installation and operation. "USA," Canadian...
Instruction Manual - Page 2
...the transceiver's Set mode setting. ● Push to toggle the Attenuator function ON or OFF. • "LOC" appears when the Attenuator function is selected. ➥ Push for 1 sec. COMMANDMIC III is not...turn the power ON. • The connected transceiver power is also turned ON, if it 's installed into the transceiver. • "SCRAM" appears when the Voice scrambler function is turned ON. ...
Instruction Manual - Page 3
...---CALL LOCAL--DUP SCRAM--TAG NORMAL-SCAN
[VOL] -34"34.206N 123"23.236W --UTC-10:10--- w Set the audio and squelch levels.
➥ Push [VOL/SQL•MONI L ] for
Blinks
1 sec.
After these instructions describe [SELECTOR] as follow: [SELECTOR VOL] : Functions as the audio volume. [SELECTOR SQL] : Functions as the squelch...
Instruction Manual - Page 4
...displayed channel as the call channel.
e Push [CH/WX•DW U/I /C ] several times to set as described at the channel comment indicator and a beep tone
sounds when a signal is still moni-...Tri-watch operation
q Select Dualwatch or Tri-watch , push [CH/WX•DW U/I/C ]
again.
⁄1 Setting TAG channels
q While pushing [H/L], push [CH/WX•DW U/I /C ] for 3 sec. (until the...
Instruction Manual - Page 5
... microphone power is automatically turned ON and the Intercom mode is adjustable in Set mode.
The audio frequency of inactivity. of the foghorn is selectable in ... normal voice level. • "TALK" appears. • "WAIT" appears while the trans- See the transceiver's instruction manual for 1 sec. w To cancel the RX Speaker mode, repeat step q.
• " RX " indicator disappears.
...
Instruction Manual - Page 6
... forward or back- When this instructions are for 1 sec. t Push [ENT] to input and set your position (latitude and longitude.... (Some functions cannot be adjustable in the DSC menu. Manually programmed position data will be held for 1 sec.
Rotate...Scrambler code*2. In this setting is installed. w While pushing [16•9], turn power ON.
• After a beep emission, a Set mode ...
Instruction Manual - Page 7
... Report" in step e automatically after 4 hours. e Set your message to the transceiver,
this step is invalid, or has not been manually updated after 2 sec. of inactivity. may differ according to ...Your position data is received.
w Select and enter the desired individual address or ID code. e Select and enter an acknowledgement "Able to the previous indication after 2 sec.,...
Instruction Manual - Page 8
.../WX] to move the cursor forward or
backward, respectively.
• Push [CLR] to cancel and return to cancel before en-
DSC Set mode (continued)
• After entering an 8-digit ID code, push [ENT] or [16•9] to enter the ID name. • 1st digit must not be checked. w Select the desired ID...
Icom HM162B Reviews
Do you have an experience with the Icom HM162B that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!