HP mp2200 - Digital Projector Support and Manuals
Popular HP mp2200 Manual Pages
User Guide - Page 29
...again. If you to the user documentation provided with your video source does not appear on the projector or remote control to select the VGA port.
4. S Press the source button one or ... without the reminder how to adjust the picture, see the name of
the video port where the source is set up, turned on page 25.
3. Hiding or showing the picture
1. TIP: If you see "Adjusting the picture and...
User Guide - Page 39
... this picture mode Restores the current picture mode to its default settings. For a new lamp, resets the hours of the picture.
Displays information and status of the projector and the remote control. Setup menu
Setup menu Language Timeout for input before automatically shutting down. Sets how many seconds the on-screen menu waits for menu Picture...
User Guide - Page 42
Turn off the projector and allow it to environmental considerations. Replacing the lamp module
As the projector operates over onto a soft surface.
4. Loosen the two screws 1 holding the lamp cover and remove the cover.
42 Maintaining the Projector You can find safety information about repairs that might be regulated due to cool for 30 minutes. 2. We recommend replacing the lamp if...
User Guide - Page 43
... 43 Insert the new lamp module into the projector and tighten the two screws. 7. Install the cover and tighten the two screws. 8. Press enter, go to Setup > Reset lamp hours, and press enter. 5. Loosen the two screws 2 on after the warm-up period, try reinstalling
the lamp. 9. If the lamp does not turn on the lamp module, and pull...
User Guide - Page 58
... any type of optical device. Disposal of this lamp may be seen. • Do not attempt to the infrared LED beam. Safety information
LED safety
The infrared ports located on the digital projector and remote control are recommended: • If the unit requires service, contact an authorized HP service center. • Do not attempt to make...
User Guide - Page 59
...-TV Interference Problems. This booklet is no guarantee that shows how your digital projector complies with respect to the receiver. • Connecting the digital projector's power cord to another power outlet.
If not installed and used in a particular installation. At the first printing of the FCC Rules. Canada
This Class B digital apparatus complies with the instructions, it can...
User Guide - Page 61
...336/EEC [1] The product was tested in a typical configuration with Part 15 of conformity
According to the following product specifications:
Safety:
IEC 60950:1999/ EN 60950:2000
IEC 60825-1:1993... interference that the product(s):
Product name:
Digital Projector
Model numbers:
mp2220 series
Regulatory model:
CRVSB-05AR
Conforms to ISO/IEC Guide 22 and EN 45014
Manufacturer's name:
...
User's Guide - Page 29
... the picture or you might have to show the display again.
If the computer display is set up, turned on and playing video. Hiding or showing the picture
1.
If you press the hide button ...the picture again. TIP: If you want to blank the picture. Be sure the projector is not shown on the projector, you see "Adjusting the picture" on the screen, you to select the VGA ...
User's Guide - Page 39
... mode Restores the current picture mode to fill the screen.
For a new lamp, resets the hours of the projector and the remote control.
Adjusts the orientation of the picture: upright or upside-down .
Sets how many seconds the on -screen menu. Sets the length of or behind the screen. Show tests for input before...
User's Guide - Page 42
... to glass fragments. • This digital projector lamp contains a small amount of mercury. Unplug the power cord. 3. Disposal of the projector lamp gradually decreases and the lamp becomes more susceptible to environmental considerations. Turn off the projector and allow it to factory-fresh brightness. Replacing the lamp module
As the projector operates over onto a soft surface...
User's Guide - Page 43
Press enter, go to Setup > Reset lamp hours, and press enter. Turn on after the warm-up period, try reinstalling
the lamp. 9. Install the cover and tighten the two screws. 8.
If the lamp does not turn on the projector. Insert the new lamp module into the projector and tighten the two screws. 7. Performing routine maintenance 43 5. Loosen the two screws 2 on...
User's Guide - Page 50
... the computer manual.
if it in and press the power button again. Refer to the projector and the other end is displayed on a blank screen: • Press the source button on the computer display.
50 Fixing Problems On some notebooks, for 15 seconds, then plug it does, you see "Specifications" on .
Picture problems
If a "scanning...
User's Guide - Page 58
... the projector.
Disposal of this lamp may be seen. • Do not attempt to environmental considerations. Wash your local authorities or the Electronic Industries Alliance (www.eiae.org). Safety information
LED safety
The infrared ports located on the digital projector and remote control are recommended: • If the unit requires service, contact an authorized HP service center...
User's Guide - Page 59
... relocating the receiving antenna. • Relocating the digital projector with the limits for a Class B digital device, pursuant to operate the digital projector in accordance with the instructions, it can radiate radio frequency energy. This digital projector generates, uses, and can cause harmful interference to another power outlet. If not installed and used in these regions. For more...
User's Guide - Page 61
...Guide 22 and EN 45014
Manufacturer's name:
Hewlett Packard Company
Manufacturer's address:
Hewlett Packard Company
Digital... product(s):
Product name:
Digital Projector
Model numbers:
mp2210 series
Regulatory model:
CRVSB-05AR
Conforms to the following product specifications:
Safety:
IEC 60950:...1995+A1:2001
GB9254-1998
FCC Title 47 CFR, Part 15 Class B/ANSI C63.4:1992
AS/NZS 3548:...
HP mp2200 Reviews
Do you have an experience with the HP mp2200 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for HP yet.
Earn 750 points for your review!