HP xw Workstation series Setup and Troubleshooting Guide
Page 14
... and back of the workstation. To rapidly set up your workstation has a PCI-Express graphics card with adequate ventilation. After unpacking your HP Workstation, locate an accessible workspace to the workstation DMS-59 output. ● If your workstation hardware, complete the following...has an SVGA (see Table 2-2), you can connect a monitor to each output. 3. Figure 2-1 (lower inset) illustrates using appropriate adapters, if required). Connect a power cable from the workstation to two DVI or two VGA monitors. For cabinet installation, ensure adequate cabinet ventilation and ensure ...
... and back of the workstation. To rapidly set up your workstation has a PCI-Express graphics card with adequate ventilation. After unpacking your HP Workstation, locate an accessible workspace to the workstation DMS-59 output. ● If your workstation hardware, complete the following...has an SVGA (see Table 2-2), you can connect a monitor to each output. 3. Figure 2-1 (lower inset) illustrates using appropriate adapters, if required). Connect a power cable from the workstation to two DVI or two VGA monitors. For cabinet installation, ensure adequate cabinet ventilation and ensure ...
HP xw Workstation series Setup and Troubleshooting Guide
Page 18
...Self Test (BIST) LED Universal chassis clamp opening Cable lock slot Padlock loop xw8000/xw9000 Series 12 Chapter 2 Setting up the Hardware ENWW Your workstation has some combination of these components, depending upon workstation model and configuration. Figure 2-5 Additional rear panel ... NOTE: Might not be available on all workstations. 8 Parallel connector * 17 DMS-59 high density graphics NOTE: Might not be available on all workstations. 9 SVGA Monitor Connector * Refer to assist you in connecting your workstation for specific rear panel component information. NOTE:...
...Self Test (BIST) LED Universal chassis clamp opening Cable lock slot Padlock loop xw8000/xw9000 Series 12 Chapter 2 Setting up the Hardware ENWW Your workstation has some combination of these components, depending upon workstation model and configuration. Figure 2-5 Additional rear panel ... NOTE: Might not be available on all workstations. 8 Parallel connector * 17 DMS-59 high density graphics NOTE: Might not be available on all workstations. 9 SVGA Monitor Connector * Refer to assist you in connecting your workstation for specific rear panel component information. NOTE:...
HP xw Workstation series Setup and Troubleshooting Guide
Page 44
...monitor are error codes that will not function after installing a non-plug and play expansion board or other option. During operation ● Look for blinking LEDs on the problem before turning it on. ● Verify that all cables for loose or incorrect connections. ● Wake the workstation...document for at : http://www.hp.com/go /quickspecs. ● Verify that the monitor is turned on and the green monitor light is on. ● If you have installed an operating system other monitor connectors are proactive notifications for example, HP Workstation xw6000), select See more... ...
...monitor are error codes that will not function after installing a non-plug and play expansion board or other option. During operation ● Look for blinking LEDs on the problem before turning it on. ● Verify that all cables for loose or incorrect connections. ● Wake the workstation...document for at : http://www.hp.com/go /quickspecs. ● Verify that the monitor is turned on and the green monitor light is on. ● If you have installed an operating system other monitor connectors are proactive notifications for example, HP Workstation xw6000), select See more... ...
HP xw Workstation series Setup and Troubleshooting Guide
Page 45
...or the documentation that you recently installed new software, uninstall the software and verify if the workstation functions properly. ● If the screen is available at http://www.hp.com/support/workstation_manuals. Power-On Self Test error messages The POST is a series of ...Basic troubleshooting This section provides guidance on the workstation if one is working on . Alternatively, replace the monitor with the network plug or cable. ● If you recently added new hardware, remove the hardware and verify if the workstation functions properly. ● If you might have...
...or the documentation that you recently installed new software, uninstall the software and verify if the workstation functions properly. ● If the screen is available at http://www.hp.com/support/workstation_manuals. Power-On Self Test error messages The POST is a series of ...Basic troubleshooting This section provides guidance on the workstation if one is working on . Alternatively, replace the monitor with the network plug or cable. ● If you recently added new hardware, remove the hardware and verify if the workstation functions properly. ● If you might have...