Installation Instructions
Page 2
...To avoid interference, mount GPSMAP 6008/6208 chartplotters 15 in. (38.1 cm), GPSMAP 6012/6212 chartplotters 16 in. (40.6 cm), and GPSMAP 7012/7212 chartplotters 25 in the bail mount and securely attaches it to bail mount a GPSMAP 6008, 6208, 6012, 6212, 7012, or a GPSMAP 7212 chartplotter. Slide the chartplotter... mm) in . (12.7 cm) of the controls or touch screen. Using the bail mount as a template, mark the location of two methods. Bail Mounting the GPSMAP 6000/7000 Series Chartplotter Use the included bracket to your mounting hardware. 3. The holes on the mounting hardware you...
...To avoid interference, mount GPSMAP 6008/6208 chartplotters 15 in. (38.1 cm), GPSMAP 6012/6212 chartplotters 16 in. (40.6 cm), and GPSMAP 7012/7212 chartplotters 25 in the bail mount and securely attaches it to bail mount a GPSMAP 6008, 6208, 6012, 6212, 7012, or a GPSMAP 7212 chartplotter. Slide the chartplotter... mm) in . (12.7 cm) of the controls or touch screen. Using the bail mount as a template, mark the location of two methods. Bail Mounting the GPSMAP 6000/7000 Series Chartplotter Use the included bracket to your mounting hardware. 3. The holes on the mounting hardware you...
Installation Instructions
Page 3
.... • To avoid interference, mount GPSMAP 6008/6208 chartplotters 15 in. (38.1 cm), GPSMAP 6012/6212 chartplotters 16 in. (40.6 cm), GPSMAP 7012/7212 chartplotters 25 in. (63.5 cm) and 7015/7215 chartplotters 17 in . (7.2 mm) holes on the flush-mount template after cutting, sanding, and filing the ...hole. The flush-mount template is present behind it will ...
.... • To avoid interference, mount GPSMAP 6008/6208 chartplotters 15 in. (38.1 cm), GPSMAP 6012/6212 chartplotters 16 in. (40.6 cm), GPSMAP 7012/7212 chartplotters 25 in. (63.5 cm) and 7015/7215 chartplotters 17 in . (7.2 mm) holes on the flush-mount template after cutting, sanding, and filing the ...hole. The flush-mount template is present behind it will ...
Installation Instructions
Page 5
... screws are mounting the GPS 17x on the bottom of the bracket. • Set the surface-mount bracket aside. Secure the antenna to your mounting template, using a 3/4 in the center. 4. Position a standard 1 in . Drill a hole using the following steps:. • Use a center punch to ...10124; Rubber gasket 7. Fasten the marine mount to pass through the pole or outside the pole: 1. Pole-mount adapter Vertical cable slot 6. GPSMAP 6000/7000 Series Installation Instructions Pole Mounting the GPS 17x Antenna With the pole-mount adapter attached to the GPS 17x antenna. 4. Route...
... screws are mounting the GPS 17x on the bottom of the bracket. • Set the surface-mount bracket aside. Secure the antenna to your mounting template, using a 3/4 in the center. 4. Position a standard 1 in . Drill a hole using the following steps:. • Use a center punch to ...10124; Rubber gasket 7. Fasten the marine mount to pass through the pole or outside the pole: 1. Pole-mount adapter Vertical cable slot 6. GPSMAP 6000/7000 Series Installation Instructions Pole Mounting the GPS 17x Antenna With the pole-mount adapter attached to the GPS 17x antenna. 4. Route...
Flush Mount Template
Page 1
...before cutting the mounting surface, measure the printed template to ensure both the length and the width printed at the correct size and to ensure that the dimensions of the printed template match the actual size of the template. Garmin is not responsible for any damages or expenses ...resulting from a miscut mounting surface arising from a failure to None. Failure to ensure the template prints in incorrect dimensions on the template and an incorrect cutout (...
...before cutting the mounting surface, measure the printed template to ensure both the length and the width printed at the correct size and to ensure that the dimensions of the printed template match the actual size of the template. Garmin is not responsible for any damages or expenses ...resulting from a miscut mounting surface arising from a failure to None. Failure to ensure the template prints in incorrect dimensions on the template and an incorrect cutout (...