Owner's Manual
Page 8
...may need this information to update the system software or to set speed, track control, position, simulator time, and simulator date. GPSMAP® 4000/5000 Series Owner's Manual Insert blank SD cards to transfer data such as waypoints, routes, and tracks to the original ... another compatible Garmin unit or a computer. The unit does not track satellites in until it from the chartplotter. Viewing System Information You can restore your chartplotter. From the Home screen, select Configure > System > System Information. Card label GPSMAP 4010 and 4012 Card label GPSMAP 4008 and ...
...may need this information to update the system software or to set speed, track control, position, simulator time, and simulator date. GPSMAP® 4000/5000 Series Owner's Manual Insert blank SD cards to transfer data such as waypoints, routes, and tracks to the original ... another compatible Garmin unit or a computer. The unit does not track satellites in until it from the chartplotter. Viewing System Information You can restore your chartplotter. From the Home screen, select Configure > System > System Information. Card label GPSMAP 4010 and 4012 Card label GPSMAP 4008 and ...
Owner's Manual
Page 36
...When On is selected, the chartplotter will automatically turn on whenever power is applied, unless the chartplotter is named Demo.) Auto Power Up (GPSMAP 4010 and GPSMAP 5015 only)-turn in a route that you transition to the next leg. Select the event to configure unit settings. The Save to toggle... Beeper/Display-select Beeper to use this setting is turned off (page 54). Select Backlight to turn Simulator Mode On or Off. a Garmin Product Support representative may ask you set simulator options. (If you to set how much time or how far before power is hidden. Configuring...
...When On is selected, the chartplotter will automatically turn on whenever power is applied, unless the chartplotter is named Demo.) Auto Power Up (GPSMAP 4010 and GPSMAP 5015 only)-turn in a route that you transition to the next leg. Select the event to configure unit settings. The Save to toggle... Beeper/Display-select Beeper to use this setting is turned off (page 54). Select Backlight to turn Simulator Mode On or Off. a Garmin Product Support representative may ask you set simulator options. (If you to set how much time or how far before power is hidden. Configuring...
Owner's Manual
Page 57
.... (1 m) GPSMAP 4010: 3.3 ft. (1 m) GPSMAP 5015: 1.3 ft. (40 cm) Hg - GPS Performance (with GPS 17 antenna) Receiver: Differential-ready 12 parallel channel WAAS-capable receiver Acquisition Times: Warm: 15 seconds Cold: 45 seconds AutoLocate: 2 minutes Update Rate: 1/second, continuous GPS Accuracy: Position: Range: from 5° to 131°F (from -15° to : www.garmin.com...
.... (1 m) GPSMAP 4010: 3.3 ft. (1 m) GPSMAP 5015: 1.3 ft. (40 cm) Hg - GPS Performance (with GPS 17 antenna) Receiver: Differential-ready 12 parallel channel WAAS-capable receiver Acquisition Times: Warm: 15 seconds Cold: 45 seconds AutoLocate: 2 minutes Update Rate: 1/second, continuous GPS Accuracy: Position: Range: from 5° to 131°F (from -15° to : www.garmin.com...
Owner's Manual
Page 58
... file on the card and paste it into an SD card reader that is displayed. When you are on a screen you want to capture: • (GPSMAP 4000 series) Press the HOME button on the unit for at least six seconds. 5. Appendix WAAS Accuracy: Position: System > Beeper/Display. 3. Select OK when... the Screenshot Taken window is attached to any location on the Garmin RF Wireless Remote Control for at least six seconds. • (GPSMAP 5000 series) Press the HOME button on the computer. From Windows Explorer, open the Garmin\scrn folder on the SD card. 3. Remove the SD card from the ...
... file on the card and paste it into an SD card reader that is displayed. When you are on a screen you want to capture: • (GPSMAP 4000 series) Press the HOME button on the unit for at least six seconds. 5. Appendix WAAS Accuracy: Position: System > Beeper/Display. 3. Select OK when... the Screenshot Taken window is attached to any location on the Garmin RF Wireless Remote Control for at least six seconds. • (GPSMAP 5000 series) Press the HOME button on the computer. From Windows Explorer, open the Garmin\scrn folder on the SD card. 3. Remove the SD card from the ...
Installation Instructions
Page 4
...the pilot holes on the back. Note: Stainless-steel screws may bind when screwed into place. GPSMAP 4000/5000 Series Installation Instructions Garmin recommends applying an anti-galling, stainless antiseize lubricant to the screw before using. 12.Replace the mounting covers... (page 20) with the holes. Securely tighten the included mounting screws through only the top gel-coat layer. Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter: Hardware (included): • Flush-mount template Tools required (not included): • Jigsaw • Rubber gasket...
...the pilot holes on the back. Note: Stainless-steel screws may bind when screwed into place. GPSMAP 4000/5000 Series Installation Instructions Garmin recommends applying an anti-galling, stainless antiseize lubricant to the screw before using. 12.Replace the mounting covers... (page 20) with the holes. Securely tighten the included mounting screws through only the top gel-coat layer. Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter: Hardware (included): • Flush-mount template Tools required (not included): • Jigsaw • Rubber gasket...
Installation Instructions
Page 18
..., install a switch. Relay 100 ma max coil current Lamp Wiring to a DB-9 PC Serial Connector The GPSMAP 4008/4208/4010/4210/4012/4212/5008/5208/5012/5212 chartplotters can be connected to a PC with a lamp, a horn, or both . Garmin GPSMAP 4000/5000 series chartplotter Power cable NMEA 0183 Cable Wire see table for the...
..., install a switch. Relay 100 ma max coil current Lamp Wiring to a DB-9 PC Serial Connector The GPSMAP 4008/4208/4010/4210/4012/4212/5008/5208/5012/5212 chartplotters can be connected to a PC with a lamp, a horn, or both . Garmin GPSMAP 4000/5000 series chartplotter Power cable NMEA 0183 Cable Wire see table for the...
Installation Instructions
Page 19
...separate NTSC/PAL compatible video devices, such as VCR, DVD, TV, or a video camera. Marine Video inputs are attached and will not transmit over the Garmin Marine Network. ➊ and ➋ VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from video device attaches to which they are only ...sync-Gnd HD-15 Pin 13 7 VGA, H-sync HD-15 Pin 14 12 VGA, V-sync HD-15 Pin shell 9 VGA, overall shield GPSMAP 4000/5000 Series Installation Instructions 19 Marine Video Cable The included Marine Video 17-pin cable allows input of NTSC (National Television System Committee)/PAL...
...separate NTSC/PAL compatible video devices, such as VCR, DVD, TV, or a video camera. Marine Video inputs are attached and will not transmit over the Garmin Marine Network. ➊ and ➋ VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from video device attaches to which they are only ...sync-Gnd HD-15 Pin 13 7 VGA, H-sync HD-15 Pin 14 12 VGA, V-sync HD-15 Pin shell 9 VGA, overall shield GPSMAP 4000/5000 Series Installation Instructions 19 Marine Video Cable The included Marine Video 17-pin cable allows input of NTSC (National Television System Committee)/PAL...
Quick Reference Guide
Page 2
...-press to adjust the backlight and color mode. MENU-press to customize the Combinations screen. Numeric Keypad (4010/4210/4012/4212 only)-enter numbers and letters into fields instead of Garmin. Go to automatically adjust the backlight based on ambient light, select Auto. • To manually adjust ...from any screen to return to toggle the data bar on or off. • Select a numbered option, such as a Waypoint. Garmin®, the Gamin logo, GPSMAP®, BlueChart®, and g2 Vision® are connected to network devices such as sonar and radar, more combination screen options will ...
...-press to adjust the backlight and color mode. MENU-press to customize the Combinations screen. Numeric Keypad (4010/4210/4012/4212 only)-enter numbers and letters into fields instead of Garmin. Go to automatically adjust the backlight based on ambient light, select Auto. • To manually adjust ...from any screen to return to toggle the data bar on or off. • Select a numbered option, such as a Waypoint. Garmin®, the Gamin logo, GPSMAP®, BlueChart®, and g2 Vision® are connected to network devices such as sonar and radar, more combination screen options will ...