Manual/User Guide
Page 1
C141-E274 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
C141-E274 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide
Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E274 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E274 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Manual/User Guide
Page 3
... specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. C141-E274 3-3 When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD...
... specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. C141-E274 3-3 When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD...
Manual/User Guide
Page 4
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E274 Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us.
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E274 Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us.
Manual/User Guide
Page 5
Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Locating of breather C141-E274 3-5
Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Locating of breather C141-E274 3-5
Manual/User Guide
Page 6
... standard values No. Regardless of the DE. To check the cooling efficiency, measure the surface cover temperatures of the ambient temperature, this surface cover temperature must be considered to the ambient temperature at a point 3 cm from exceeding 60 °C. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover...
... standard values No. Regardless of the DE. To check the cooling efficiency, measure the surface cover temperatures of the ambient temperature, this surface cover temperature must be considered to the ambient temperature at a point 3 cm from exceeding 60 °C. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover...
Manual/User Guide
Page 7
...Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Pressing it by external magnetic fields. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Ensure that the disk drive... HDD under the safety environment. Damage: Do not press the cover of the disk drive. Static: When handling the device, disconnect the body ground (500 kΩ or greater). Do not touch the printed circuit board, but hold it too hard,...
...Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Pressing it by external magnetic fields. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Ensure that the disk drive... HDD under the safety environment. Damage: Do not press the cover of the disk drive. Static: When handling the device, disconnect the body ground (500 kΩ or greater). Do not touch the printed circuit board, but hold it too hard,...
Manual/User Guide
Page 8
...Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E274 General notes Wrist strap Use the Wrist strap. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque... of a low impact when you use an electric driver. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not place HDD vertically to avoid falling down. Installation (1) Please use the driver ...
...Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E274 General notes Wrist strap Use the Wrist strap. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque... of a low impact when you use an electric driver. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not place HDD vertically to avoid falling down. Installation (1) Please use the driver ...
Manual/User Guide
Page 9
Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E274 3-9
Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E274 3-9
Manual/User Guide
Page 10
... 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification. For detail of the SATA interface connector and pin numbers. The connection reliability per number of insertion/extractions varies with the condition of host system for host system The connector of the connection with the Serial ATA Revision 2.5 specification. 3-10 C141-E274 Power supply segment Signal segment View from the connector side P1 pins in the power...
... 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification. For detail of the SATA interface connector and pin numbers. The connection reliability per number of insertion/extractions varies with the condition of host system for host system The connector of the connection with the Serial ATA Revision 2.5 specification. 3-10 C141-E274 Power supply segment Signal segment View from the connector side P1 pins in the power...
Manual/User Guide
Page 11
... cable without releasing the SATA interface Latch may lead to connect/remove the cable while releasing the Latch. Accordingly, be compliant with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be sure to connector damage and the loss of force in the connection direction once they are snugly and securely in position. 3.3 Connections with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection...
... cable without releasing the SATA interface Latch may lead to connect/remove the cable while releasing the Latch. Accordingly, be compliant with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be sure to connector damage and the loss of force in the connection direction once they are snugly and securely in position. 3.3 Connections with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection...