Literature/Product Sheet
Page 2
...DENON A/V receivers, this Movie mode is not configured for output to an additional zone, in addition to the main room. Learning functions - The AVR-2803's Power Amplifier Assign function lets you assign the 2 Surround Back (SB L/R) amplifier channels when the system is displayed as "MODE CINEMA". *Design and specifications...-1, VCR-2, MONITOR 3 Sets Composite Output VCR-1, VCR-2, MONITOR Specifications ■ Power Amplifier Section Rated output *THD figures are power amp stage values. NEW MODEL I N F O R M A T I O N AVR-2803 ■ 24 bit, 96 kHz All-channels Differential-mode ...
...DENON A/V receivers, this Movie mode is not configured for output to an additional zone, in addition to the main room. Learning functions - The AVR-2803's Power Amplifier Assign function lets you assign the 2 Surround Back (SB L/R) amplifier channels when the system is displayed as "MODE CINEMA". *Design and specifications...-1, VCR-2, MONITOR 3 Sets Composite Output VCR-1, VCR-2, MONITOR Specifications ■ Power Amplifier Section Rated output *THD figures are power amp stage values. NEW MODEL I N F O R M A T I O N AVR-2803 ■ 24 bit, 96 kHz All-channels Differential-mode ...
Owners Manual
Page 4
... ⁄3 Last Function Memory 63 ⁄4 Initialization of the Microprocessor 63 ⁄5 Troubleshooting 64 ⁄6 Additional Information 65~74 ⁄7 Specifications 75 2 ACCESSORIES Check that the following parts are included in addition to the main unit: q Operating instructions.....1 w Warranty ( for North... tuner or TV. • Set the antenna wires from the tuner or TV away from the actual set for choosing the DENON AVR-2803/983 Digital A / V Surround Receiver. This remarkable component has been engineered to occur particularly when using microprocessors is provided with...
... ⁄3 Last Function Memory 63 ⁄4 Initialization of the Microprocessor 63 ⁄5 Troubleshooting 64 ⁄6 Additional Information 65~74 ⁄7 Specifications 75 2 ACCESSORIES Check that the following parts are included in addition to the main unit: q Operating instructions.....1 w Warranty ( for North... tuner or TV. • Set the antenna wires from the tuner or TV away from the actual set for choosing the DENON AVR-2803/983 Digital A / V Surround Receiver. This remarkable component has been engineered to occur particularly when using microprocessors is provided with...
Owners Manual
Page 26
.... 0 dB, -40 dB: The output level is fixed at the set level and the volume can be adjusted. 4 Enter the setting. Select according to the specifications of the analog input signal connected to the Ext.In Subwoofer. 1 At the System Setup Menu select "Ext.In Subwoofer Level". 2 Switch to the player...
.... 0 dB, -40 dB: The output level is fixed at the set level and the volume can be adjusted. 4 Enter the setting. Select according to the specifications of the analog input signal connected to the Ext.In Subwoofer. 1 At the System Setup Menu select "Ext.In Subwoofer Level". 2 Switch to the player...
Owners Manual
Page 75
... 58 (W) x 230 (H) x 37 (D) mm (2-9/32" x 9-1/16" x 1-29/64") Mass: 230 g (Approx. 8 oz) (including batteries) * For purposes of improvement, specifications and design are subject to -noise ratio: 74 dB (A weighting, with 0.7% T.H.D.) Dynamic power: 120 W x 2 ch (8 Ω/ohms) 170 W x 2 ch (4 Ω/ohms...Surround, Surr. REC OUT) Input sensitivity: 2.5 mV RIAA deviation: ±1 dB (20 Hz to 20 kHz) Signal-to change without notice. 75 17 SPECIFICATIONS 2 Audio section • Power amplifier Rated output: Front: 90 W + 90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05% ...
... 58 (W) x 230 (H) x 37 (D) mm (2-9/32" x 9-1/16" x 1-29/64") Mass: 230 g (Approx. 8 oz) (including batteries) * For purposes of improvement, specifications and design are subject to -noise ratio: 74 dB (A weighting, with 0.7% T.H.D.) Dynamic power: 120 W x 2 ch (8 Ω/ohms) 170 W x 2 ch (4 Ω/ohms...Surround, Surr. REC OUT) Input sensitivity: 2.5 mV RIAA deviation: ±1 dB (20 Hz to 20 kHz) Signal-to change without notice. 75 17 SPECIFICATIONS 2 Audio section • Power amplifier Rated output: Front: 90 W + 90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05% ...
Serial Protocol
Page 2
...it is the same as a pause sign. Command structure : COMMAND + PARAMETER + CR (0x0D) COMMAND : ASCII CODE of EVENT. Basic specification : The command by ASCII CODE, parameter expression *ASCII CODE which can be sent within 200ms of receiving the COMMAND. *The form of ...Panel etc.) from a system (AVR/AVC) If the 'request command' (COMMAND+?+CR (0x0D)) has came from a controller(Touch Panel etc.) A command to the following three data forms are defined. It is used is given from 0x20 to 25 characters) ex. Protocol specification The following table for request command...
...it is the same as a pause sign. Command structure : COMMAND + PARAMETER + CR (0x0D) COMMAND : ASCII CODE of EVENT. Basic specification : The command by ASCII CODE, parameter expression *ASCII CODE which can be sent within 200ms of receiving the COMMAND. *The form of ...Panel etc.) from a system (AVR/AVC) If the 'request command' (COMMAND+?+CR (0x0D)) has came from a controller(Touch Panel etc.) A command to the following three data forms are defined. It is used is given from 0x20 to 25 characters) ex. Protocol specification The following table for request command...