Rack-to-Tower Conversion Guide (.pdf)
Page 3
... This document provides instructions for installing a 1 x 2 backplane kit to add provisions for up to two additional 1-inch small computer system interface (SCSI) hard-disk drives in a Dell™ system's peripheral bay. 1 x 2 Backplane Kit Contents The 1 x 2 backplane kit includes the following items: • A 1 ...• Four 6-32 x 0.25-inch hex-head Phillips screws • Inter-integrated circuit (I2C) extension cable • Nonterminated SCSI cable that your Installation and Troubleshooting Guide. 1 Turn off the system and disconnect it from its power source. For more information,...
... This document provides instructions for installing a 1 x 2 backplane kit to add provisions for up to two additional 1-inch small computer system interface (SCSI) hard-disk drives in a Dell™ system's peripheral bay. 1 x 2 Backplane Kit Contents The 1 x 2 backplane kit includes the following items: • A 1 ...• Four 6-32 x 0.25-inch hex-head Phillips screws • Inter-integrated circuit (I2C) extension cable • Nonterminated SCSI cable that your Installation and Troubleshooting Guide. 1 Turn off the system and disconnect it from its power source. For more information,...
Rack-to-Tower Conversion Guide (.pdf)
Page 7
... connector on the system board. Installing the I2C Extension Cable 1 Disconnect the I2C cable connector at the 20-pin PLANAR connector on system board nonterminated SCSI cable cooling shroud cable clips 1 x 2 Backplane Kit Installation Guide 1-5 NOTE: Figure 1-3 shows the 1 x 2 backplane and its drive cage oriented 180...the locking slots in the chassis and slide the peripheral bay forward. 4 Tighten the thumbscrew securing the peripheral bay to the SCSI backplane. 2 In the customer kit, locate the I2C extension cable. Do not disconnect the end that is connected to the chassis (see...
... connector on the system board. Installing the I2C Extension Cable 1 Disconnect the I2C cable connector at the 20-pin PLANAR connector on system board nonterminated SCSI cable cooling shroud cable clips 1 x 2 Backplane Kit Installation Guide 1-5 NOTE: Figure 1-3 shows the 1 x 2 backplane and its drive cage oriented 180...the locking slots in the chassis and slide the peripheral bay forward. 4 Tighten the thumbscrew securing the peripheral bay to the SCSI backplane. 2 In the customer kit, locate the I2C extension cable. Do not disconnect the end that is connected to the chassis (see...
Rack-to-Tower Conversion Guide (.pdf)
Page 8
...the new I2C extension cable that is the standard cable found on all systems and provides power to peripherals, such as a tape drive. www.dell.com | support.dell.com NOTICE: The I2C cable must be routed over the top of the cooling shroud. 3 Route the I2C extension cable through the clips on... connector on the end of the cable to the vertical connector that you installed in this end of the cable to a Peripheral Component Interconnect (PCI) SCSI or PCI RAID controller card. 1-6 1 x 2 Backplane Kit Installation Guide NOTE: The four-wire power cable is closest to the 10-pin I2C connector on...
...the new I2C extension cable that is the standard cable found on all systems and provides power to peripherals, such as a tape drive. www.dell.com | support.dell.com NOTICE: The I2C cable must be routed over the top of the cooling shroud. 3 Route the I2C extension cable through the clips on... connector on the end of the cable to the vertical connector that you installed in this end of the cable to a Peripheral Component Interconnect (PCI) SCSI or PCI RAID controller card. 1-6 1 x 2 Backplane Kit Installation Guide NOTE: The four-wire power cable is closest to the 10-pin I2C connector on...
SCSI Backplane Daughter Card Installation (.pdf)
Page 3
...data loss, you should back up all data on the hard-disk drives before changing the mode of operation of the integrated SCSI controller from SCSI to RAID. 1 Turn off the system and disconnect it from its power source. Your upgrade kit includes a RAID controller ...). 5 Open the ejectors on the system board. CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your Dell™ system's integrated PowerEdge™ Expandable RAID 3/Di controller (PERC 3/Di). Activating the Integrated RAID Controller 1-1 About This Guide This document explains how ...
...data loss, you should back up all data on the hard-disk drives before changing the mode of operation of the integrated SCSI controller from SCSI to RAID. 1 Turn off the system and disconnect it from its power source. Your upgrade kit includes a RAID controller ...). 5 Open the ejectors on the system board. CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your Dell™ system's integrated PowerEdge™ Expandable RAID 3/Di controller (PERC 3/Di). Activating the Integrated RAID Controller 1-1 About This Guide This document explains how ...