User Guide
Page 2
... Installing internal options...15 Available internal options...15 Accessing the system board to install internal options...16 Installing a memory card ...18 Installing a flash memory or firmware card...19 Installing an Internal Solutions Port...21 Installing a printer hard disk ...28 Installing hardware options...32 Order of installation ...32 Installing paper drawers...32...
... Installing internal options...15 Available internal options...15 Accessing the system board to install internal options...16 Installing a memory card ...18 Installing a flash memory or firmware card...19 Installing an Internal Solutions Port...21 Installing a printer hard disk ...28 Installing hardware options...32 Order of installation ...32 Installing paper drawers...32...
User Guide
Page 15
... 10/100 Fiber ISP - Flash memory - MarkNetTM N8150 802.11 b/g/n Wireless ISP - For more information, contact the place where you purchased the printer. Fonts • Firmware cards - PrintCryptionTM • Printer hard disk • Internal Solutions Ports (ISP) - Additional printer setup 15 RS-232-C Serial ISP - MarkNet N8120 10/100/1000 Ethernet...
... 10/100 Fiber ISP - Flash memory - MarkNetTM N8150 802.11 b/g/n Wireless ISP - For more information, contact the place where you purchased the printer. Fonts • Firmware cards - PrintCryptionTM • Printer hard disk • Internal Solutions Ports (ISP) - Additional printer setup 15 RS-232-C Serial ISP - MarkNet N8120 10/100/1000 Ethernet...
User Guide
Page 17
Touch something metal on the printer before touching any system board electronic components or connectors. 1 Firmware and flash memory card connectors 2 Memory card connector 3 Internal Solutions Port or printer hard disk connector Additional printer setup 17 3 Remove the system board cover. 4 Use the illustration below to locate the appropriate connector. Warning-Potential Damage: System board electronic components are easily damaged by static electricity.
Touch something metal on the printer before touching any system board electronic components or connectors. 1 Firmware and flash memory card connectors 2 Memory card connector 3 Internal Solutions Port or printer hard disk connector Additional printer setup 17 3 Remove the system board cover. 4 Use the illustration below to locate the appropriate connector. Warning-Potential Damage: System board electronic components are easily damaged by static electricity.
User Guide
Page 19
4 Align the notches on the memory card with the ridges on the connector. 1 Notches 2 Ridges 5 Push the memory card straight into the connector until it snaps into place. 6 Replace the system board cover and close the system board door. Installing a flash memory or firmware card Note: This task requires a flathead screwdriver. Additional printer setup 19
4 Align the notches on the memory card with the ridges on the connector. 1 Notches 2 Ridges 5 Push the memory card straight into the connector until it snaps into place. 6 Replace the system board cover and close the system board door. Installing a flash memory or firmware card Note: This task requires a flathead screwdriver. Additional printer setup 19
User Guide
Page 20
... or connectors. 1 Access the system board. 2 Unpack the card. If you are interchangeable. The system board has two connections for an optional flash memory or firmware card.
... or connectors. 1 Access the system board. 2 Unpack the card. If you are interchangeable. The system board has two connections for an optional flash memory or firmware card.
User Guide
Page 159
... Try one or more of the following : 1 Turn the printer power off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. Try one or more of the following : • Press the arrow buttons until Continue appears, and then press to... buttons until Continue appears, and then press • Turn the printer off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server.
... Try one or more of the following : 1 Turn the printer power off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. Try one or more of the following : • Press the arrow buttons until Continue appears, and then press to... buttons until Continue appears, and then press • Turn the printer off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server.
User Guide
Page 160
... not set to clear the message. 56 Serial port disabled is the number of the serial port. to Disabled. Possible changes include: • The printer firmware has been updated. • Paper input, output, or duplex options needed for the print job were removed. • The print job was created using data...
... not set to clear the message. 56 Serial port disabled is the number of the serial port. to Disabled. Possible changes include: • The printer firmware has been updated. • Paper input, output, or duplex options needed for the print job were removed. • The print job was created using data...
User Guide
Page 161
... from the wall outlet. 3 Remove extra flash options. 4 Connect the power cord to a properly grounded outlet. 5 Turn the printer back on. 58 Too many optional firmware cards are supported. Understanding printer messages 161 58 Too many bins attached 1 Turn the printer power off. 2 Unplug the power cord from the wall outlet...
... from the wall outlet. 3 Remove extra flash options. 4 Connect the power cord to a properly grounded outlet. 5 Turn the printer back on. 58 Too many optional firmware cards are supported. Understanding printer messages 161 58 Too many bins attached 1 Turn the printer power off. 2 Unplug the power cord from the wall outlet...
User Guide
Page 163
... continue printing. 1565 Emulation error, load emulation option The printer automatically clears the message in 30 seconds and then disables the download emulator on the firmware card. Replace the print cartridge, and then press to clear the message and continue printing. 88.yy Cartridge nearly low The toner is low. Replace...
... continue printing. 1565 Emulation error, load emulation option The printer automatically clears the message in 30 seconds and then disables the download emulator on the firmware card. Replace the print cartridge, and then press to clear the message and continue printing. 88.yy Cartridge nearly low The toner is low. Replace...
User Guide
Page 202
... needed 167 notice that different paper is needed 167 F factory defaults, restoring 169 FCC notices 190, 194 fiber optic network setup 43 Finishing menu 129 firmware card installing 19 flash drive 75 Flash Drive menu 138 flash memory card installing 19 troubleshooting 177 Flushing buffer 145 font sample list printing 76...
... needed 167 notice that different paper is needed 167 F factory defaults, restoring 169 FCC notices 190, 194 fiber optic network setup 43 Finishing menu 129 firmware card installing 19 flash drive 75 Flash Drive menu 138 flash memory card installing 19 troubleshooting 177 Flushing buffer 145 font sample list printing 76...
User Guide
Page 203
... file types 149 noise emission levels 191 Not Ready 149 notices 190, 191, 192, 193, 194, 195 O options duplex unit 33 fax card 15 firmware card 19 firmware cards 15 flash memory card 19 internal 15 Internal Solutions Port 21 memory card 18 memory cards 15 networking 15 paper drawers 32 ports...
... file types 149 noise emission levels 191 Not Ready 149 notices 190, 191, 192, 193, 194, 195 O options duplex unit 33 fax card 15 firmware card 19 firmware cards 15 flash memory card 19 internal 15 Internal Solutions Port 21 memory card 18 memory cards 15 networking 15 paper drawers 32 ports...