D-Link DES-3326 Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DES-3326 manuals!
Problems with D-Link DES-3326?
Ask a Question
Free D-Link DES-3326 manuals!
Problems with D-Link DES-3326?
Ask a Question
Most Recent D-Link DES-3326 Questions
Vlan Tagging
Is there a way to block VLAN tagging? We are trying to combine two ISP's on 1 VLAN and ISP "A" shuts...
Is there a way to block VLAN tagging? We are trying to combine two ISP's on 1 VLAN and ISP "A" shuts...
(Posted by hartjed 12 years ago)
Popular D-Link DES-3326 Manual Pages
Configuration Guide - Page 1
... 1.00B19. Network Configuration.
Introduction
This guide will help you to setup a routing function to have the latest firmware installed in the switch before embarking on the configuration. ftp://ftp.dlink.co.uk
Network Configuration
Fig 1. Please visit the UK ftp site for the latest firmware releases. Model:
DES-3326
Firmware Version 1.00B19
OS Supported:
Windows 95, Windows 98...
Configuration Guide - Page 2
... on ports 1 & 2. To do this document, fig 1. Fig 2. The DES-3326 thus has achieved the act of what can ping PC2. Configuration Procedure
Before you begin the layer 3 configuration, you will be configured if layer 2 switches also exist in fig 1. The default username and password is layer 2. Two departments are segmented using layer 3 routing protocol...
Configuration Guide - Page 3
You will be presented with the main menu options as shown in fig 3.
Fig 3. Switch Main Menu
Select from the main menu 'Switch Settings'
Fig 4. return. return - Switch Settings Menu
From the switch settings menu select 'Switch Operating Mode'
Configuration Guide - Page 4
... the configuration parameters in fig 5. Please note, you have completed the above. Proceed to 'IP Routing, support IEEE 802.1Q VLANs' as in the 'Remote management setup' leave them at there default settings, fig 6. Apply the changes, the switch will reboot.
Switch Operating Mode
Using the space bar change any of the configuration, that is to the...
Configuration Guide - Page 5
Main Menu
From the main menu select 'VLAN's'
Fig 8. The default PVID for sales use PVID=2, for all ports is set to configure the port VLAN ID (PVID) before configuring the 802.1Q VLAN's. Fig 7. You will need to 1. For setting up VLAN's for the engineering department use PVID=3 as shown in Fig. 9. VLAN Menu
Select 'Configure 802.1Q Port Settings'.
Configuration Guide - Page 6
...cursor to the VID and enter '2', again use the same number as is, ie do not change the default VID. Go to VLAN name and enter an appropriate name. You will need to configure the 802.1Q ...VLAN's. In this example we have the first octet of the IP adress. Fig 9. 802.1Q Port Settings
After the above is completed your ready to leave the default VLAN as used for the PVID previously.
Fig 10. 802....
Configuration Guide - Page 7
... ready to these ports may not be Tag compliant. From the main menu select layer 3 IP Networking, then select 'Setup IP Interface'
Fig 11. This is so because adapters connected to configure you layer 3 routing configuration within the switch. Repeat the procedure for Untag. You will need to Egress all the port members of...
Configuration Guide - Page 8
... looks okay return to the main menu and save the configuration. The IP address is the IP address of the the switch in that particular subnet, we have used the fist octet for the interface name. After the config is the PVID set in fig 12.
Once again in this example we have choosen...
Configuration Guide - Page 9
You may need to a PC on the 192 subnet to perform a factory reset and re-config the switch.
~ End of Document ~ Fig. 15 Save Configuration
How to Test the Configuration
To test the configuration, do a ping test from a PC on the 200 subnet. If the ping test produces a 'request timed out' check the configuration above more carefully. If succesful, the layer configuration is complete.
D-Link DES-3326 Reviews
We have not received any reviews for D-Link yet.