Cisco WS-X4516-10GE - Supervisor Engine V-10GE Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4516-10GE manuals!
Problems with Cisco WS-X4516-10GE?
Ask a Question
Free Cisco WS-X4516-10GE manuals!
Problems with Cisco WS-X4516-10GE?
Ask a Question
Cisco WS-X4516-10GE Videos
Cisco WS-X4516-10GE $1600 Price Reduction
Duration: :34
Total Views: 8
Duration: :34
Total Views: 8
Popular Cisco WS-X4516-10GE Manual Pages
Hardware Maintenance Manual - Page 3
... for the Software in this manual is error free or that Cisco or its Sales Partner cannot reasonably reproduce the Software error, (6) has been exported from the date of destination without problems or interruptions. Customer agrees to cooperate with respect to nonconforming Software upon contact will substantially conform to the published specifications for a remedy, Customer must...
Hardware Maintenance Manual - Page 4
... Partner if necessary, to either (i) provide advance replacement service as authorized by Cisco, (3) has been subjected to any installation, handling, maintenance, or operating instructions supplied by Cisco, (2) has not been installed, operated, repaired, or maintained in Cisco's recommended spares list. Exclusions. In no event does Cisco warrant that supplied the Product to Customer or to...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 15
..., installation, troubleshooting, and selected upgrade and maintenance procedures.
About This Manual xv About This Manual
This section discusses the objectives, audience, organization, and conventions of product information. Use this publication follow:
• Chapter 1, "Cisco 4000 Series Overview," contains an overview of the Cisco 4000 series features
and physical specifications...
Hardware Maintenance Manual - Page 16
...
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory modules (SIMMs).
• Appendix A, "Cabling Specifications...
Hardware Maintenance Manual - Page 20
...; User-upgradable network processor modules, shared memory, and processor local memory • Hardware thermal alarm to three network processor modules at a time, including Ethernet, Token Ring,
serial, single-mode and multimode Fiber Distributed Data Interface (FDDI), ISDN BRI, G.703, channelized T1/PRI, channelized T1/PRI, and ATM modules. Note The Cisco 4500-M and Cisco 4700 support all...
Hardware Maintenance Manual - Page 28
...following additional external equipment:
• Data service unit (DSU) to connect each procedure is performed on the router, update the Site Log to the router. ...replacement of ongoing
router maintenance and expansion history. Maintenance procedures performed
- Keep it in a common place near the chassis where anyone who performs tasks has access to verify steps in the installation...
Hardware Maintenance Manual - Page 37
...
78
102
31
50
15
Balanced drivers allow EIA/TIA-449 signals to travel...Installation 2-15 The network end of the adapter cable is a standard 25-pin D-shell connector known as EIA/TIA-232. Network Connection Considerations
Serial Connections
When setting up to 64 Kbps. If you understand the electrical problems... support synchronous connections, and the console and auxiliary ports support ...
Hardware Maintenance Manual - Page 43
.... See the appendix "Cabling Specifications." Nine different serial cables are not interchangeable. An error message will be generated if...manually changed. Note that the cables for the two versions are available for the two versions of serial modules: both DTE and DCE versions of the port-for example, if the cable is DTE and the clock rate is set the jumpers for Installation 2-21
To set...
Hardware Maintenance Manual - Page 44
...serial 0 dce-terminal-timing-enable
2-22 Cisco 4000 Series Hardware Installation and Maintenance If the DTE device does not...the SCTE signal that use long cables may experience high error rates when operating at the higher transmission speeds. In ...set the clock speed with the clockrate configuration command. To use a port as a bits-per-second value.
Configuration commands are not supported...
Hardware Maintenance Manual - Page 54
... Input port specifications: see Figure 2-35) controls this function. Figure 2-35 also shows the location of 2.048 Mbps. LOOPBACK LOCAL ALARM REMOTE ALARM H3154
Network Connection Considerations
Channelized E1 Connections
The Cisco 4000 series router supports a channelized E1 (CE1) network processor module with capacitive coupling between the receive (Rx) shield and chassis ground. On...
Hardware Maintenance Manual - Page 55
... has been configured with BNC Connectors)
H2421
Preparing for injury, jumper J2 should be set to chassis ground. For either BNC, DB-15, Twinax, or RJ-45 connectors on the ... installed at J2 bypasses the AC-decoupling capacitor to ground, thereby coupling the interface directly to 75-ohm
1. This is a setting that could pose a risk of severe injury.
Warning To prevent problems ...
Hardware Maintenance Manual - Page 123
... appendix describes the Cisco 4000-M ROM monitor, also known as the bootstrap program.
If you set the configuration to 0x0, you must manually boot the system ...you set the software configuration register (bits 3, 2, 1, and 0) to 0x0 by setting the configuration register. During the 60-second window, you isolate or rule out hardware problems encountered when installing your router. Cisco 4000...
Hardware Maintenance Manual - Page 127
... is powered-up or reset. If you set the configuration to 0x0, you will have to manually boot the system from the console each time you isolate or rule out hardware problems encountered when installing your router.
APPENDIX D
Cisco 4500-M and Cisco 4700 ROM Monitor
This appendix describes the Cisco 4500-M and Cisco 4700 ROM monitor, the first software to...
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X4516-10GE Reviews
We have not received any reviews for Cisco yet.