Cisco WS-X4515 - Supervisor Engine IV Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco WS-X4515 manuals!
Problems with Cisco WS-X4515?
Ask a Question
Free Cisco WS-X4515 manuals!
Problems with Cisco WS-X4515?
Ask a Question
Cisco WS-X4515 Videos
Popular Cisco WS-X4515 Manual Pages
Hardware Maintenance Manual - Page 3
... IN PART, SOFTWARE OR DOCUMENTATION; LIMITED WARRANTY. Customer agrees to operate its networks without the prior consent of shipment. In no event does Cisco warrant that the Software is error free or that Customer will substantially conform to the published specifications for such Software, if used in accordance with any installation, handling, maintenance, or operating instructions...
Hardware Maintenance Manual - Page 4
...to the restrictions as set forth in subparagraph (c) of the replacement boards and assemblies to Cisco or the Sales or Service Partner in full force and effect. Exclusions. DISCLAIMER. If any installation, handling, maintenance, or operating instructions supplied by Cisco, (2) has not been installed, operated, repaired, or maintained in Cisco's recommended spares list. Cisco warrants to...
Hardware Maintenance Manual - Page 6
... and Upgrading the Router 5-1
Accessing the Router Internal Components 5-1 Removing the Component Tray 5-2
Removing Network Processor Modules 5-4
Memory Replacement Procedures 5-6 Replacing Main Memory SIMMs 5-8 Removing Main Memory SIMMS 5-9 Installing Main Memory SIMMs 5-11 Replacing Shared-Memory SIMMs 5-13 Inserting Shared-Memory SIMMs 5-14 Removing the Cisco 4500-M and Cisco 4700 Boot...
Hardware Maintenance Manual - Page 7
... Installation 5-20 Recovering a Lost Password 5-21
Appendix A
Cabling Specifications A-1
EIA/TIA-232 Console and Auxiliary Port Pinouts A-2
Serial Cable Pinouts A-3 EIA/TIA-232 Dual Serial Module Cable Assembly A-3 EIA/TIA-232 Four-Port Serial Module Cable Assembly A-4 EIA/TIA-449 Dual Serial Module Cable Assembly A-6 EIA/TIA-449 Four-Port Serial Module Cable Assembly A-7 V.35 Dual Serial Module...
Hardware Maintenance Manual - Page 13
...Distances 2-25 BRI Cable Specifications 2-30 Jumper Settings and Functions 2-33 BRI Cable Specifications 3-6 BRI Port Pinout (RJ-45) 3-8 Creepage and Clearance Distances Based on Voltage 3-10 Four Port Serial Network Processor Module LED Indicators 4-7 Dual Serial Network Processor Module LED Indicators 4-9 Cisco 4000-M Console and Auxiliary Port Signals A-2 Cisco 4500-M and Cisco 4700 Console and...
Hardware Maintenance Manual - Page 15
.... Note To order UniverCD, Cisco's online library of the Cisco 4000 series features
and physical specifications.
• Chapter 2, "Preparing for Installation," includes safety recommendations, tools and equipment,
site requirements, an installation checklist, console and auxiliary port cable connection considerations, network connection considerations, and instructions for inspecting the new...
Hardware Maintenance Manual - Page 16
... responses in this manual. Samples use in the European Community.
Document Conventions
• Chapter 4, "Troubleshooting the Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router...
Hardware Maintenance Manual - Page 21
... and network processor modules)
Power
Wire Gauge for DC-Input Power Connections
200W, 85 to 264 VAC, 50 to 60 Hz, or 40 to 40°C)
1.
Table 1-2 lists the processor and memory specifications for the Cisco 4000 series routers. Table 1-2
Cisco 4000 Series Processor and Memory Specifications
Description Processor Main Memory (DRAM)2
Cisco 4000-M
Cisco 4500-M
Cisco 4700
40-MHz...
Hardware Maintenance Manual - Page 28
...Phillips • One serial port adapter cable for multimode Fiber Distributed Data Interface (FDDI)
connections.
2-6 Cisco 4000 Series Hardware Installation and Maintenance Site Log entries might need the following :
- Removal or replacement of the Installation Checklist and insert it . Maintenance procedures performed
- Each time a procedure is completed.
• Upgrades and removal or...
Hardware Maintenance Manual - Page 30
...-Rear View Showing Serial Port Unit Numbering
Dual serial module Slot 3
Serial 5
Dual serial module Dual serial module
Slot 2 Serial 3
Chassis release screw
Serial 1
Slot 1
AUX
CONSOLE
Serial 4
Serial 2 Auxiliary port Serial 0 Console port
The unit numbering of these modules would be as listed in Table 2-3. H1402 a
2-8 Cisco 4000 Series Hardware Installation and Maintenance
Hardware Maintenance Manual - Page 32
... configure your selection of Ethernet network processor modules: single-port and dual-port modules.
The syntax of the media command follows:
media-type aui media-type aui 10baset The following sections describe the two types of AUI or 10BaseT on the media command.
2-10 Cisco 4000 Series Hardware Installation and Maintenance Enter the media command in...
Hardware Maintenance Manual - Page 44
... Module Systems that use a port in place of phase. Slight variances in DCE mode, the default operation is for the attached DTE device to return the clock signal (SCTE) to accept the internal clock signal:
interface serial 0 dce-terminal-timing-enable
2-22 Cisco 4000 Series Hardware Installation and Maintenance
Following are the acceptable clockrate settings...
Hardware Maintenance Manual - Page 57
...plug as you squeeze the sides of the connector. Therefore the Cisco 4500-M and Cisco 4700 routers currently support one ATM module. The SONET SC-duplex connector is shipped with STS-3c/STM...
CISCO SYSTEMS, INC. 170 W. Preparing for Installation 2-35 ATM Cabling
For single-
or multi-mode SONET connections, connect the fiber cable to be dropped. Remove the plug by pulling on the module ...
Hardware Maintenance Manual - Page 127
...-up or reset. The ROM Monitor can break to manually boot the system from the console each time you will have to the ROM monitor prompt.
The Cisco 4500-M and Cisco 4700 ROM monitor supports more features than the familiar Cisco 4000-M ROM monitor. A summary of the Cisco 4500-M and Cisco 4700 ROM monitor prompt follows:
rommon 1 >
To enable...
Hardware Maintenance Manual - Page 141
...10 four-port A-11 X.21 dual-port A-14 four-port A-15 polarity, Ethernet LED 4-5 port locations 2-7 software configuration, serial 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem...
Cisco WS-X4515 Reviews
Do you have an experience with the Cisco WS-X4515 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!