Cisco WS-X45-SUP6-E - Supervisor Engine 6-E Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X45-SUP6-E manuals!
Problems with Cisco WS-X45-SUP6-E?
Ask a Question
Free Cisco WS-X45-SUP6-E manuals!
Problems with Cisco WS-X45-SUP6-E?
Ask a Question
Cisco WS-X45-SUP6-E Videos
Cisco WS-X45-SUP6-E $8450 Price Reduction
Duration: :34
Total Views: 6
Duration: :34
Total Views: 6
Cisco WS-X45-SUP6-E $8450 Price Reduction
Duration: :34
Total Views: 14
Duration: :34
Total Views: 14
Popular Cisco WS-X45-SUP6-E Manual Pages
Hardware Maintenance Manual - Page 3
...manual is not available, or, if the license fee was zero, refund the price of the Rights in Technical Data and Computer Software clause at Cisco's option and potentially through the Sales or Service Partner, either (i) to provide a correction or a workaround for any installation, handling, maintenance, or operating instructions supplied by Cisco, (2) has not been installed, operated, repaired...
Hardware Maintenance Manual - Page 4
...software and supporting documentation are provided with respect to the Hardware, Customer must return all applicable export laws and regulations if it acquired the Hardware or the Cisco Service Partner if the Hardware was exported under the multinational uplift program.
Cisco or the Sales or Service Partner (as authorized by Cisco, (2) has not been installed, operated, repaired, or...
Hardware Maintenance Manual - Page 10
... Processor Module LEDs 4-4 Token Ring Module Network Connector 4-5 Four-Port Serial Network Processor Module Ports 4-6 G.703/G.704 Serial Network Processor Module Ports (DB-15) 4-6 Serial Port Labeled V2 4-7 Dual Serial Network Processor Module-Top View 4-8 Dual Serial Port LED Card-Side View 4-8 Dual-Attachment Single-Mode FDDI Module-End View 4-9
x Cisco 4000 Series Hardware Installation and...
Hardware Maintenance Manual - Page 15
.... UniverCD is updated and shipped monthly, so it may be familiar with a DC-input power supply. Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures. Audience
This publication is included in your local sales representative or call Customer Service.
About This Manual xv
UniverCD is...
Hardware Maintenance Manual - Page 16
... the Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line...
Hardware Maintenance Manual - Page 20
... not compatible with the Channelized T1/ISDN PRI network interface module (NP-CT1) or with any two other types of the three available positions in any of network processor modules. Note The Cisco 4500-M and Cisco 4700 support all network processor modules except the single-port Ethernet network processor module and early versions of a Cisco 4000 series router.
Series Specifications...
Hardware Maintenance Manual - Page 22
...4000-M
EPROM-based
Flash-memory based
Boot helper (xboot)
Cisco IOS
ROM monitor
Cisco 4500, Cisco 4500-M, Cisco 4700, and Cisco 4700-M
EPROM-based
Flash-memory based
ROM monitor
Boot helper (xboot)
Cisco IOS
H3537
1-4 Cisco 4000 Series Hardware Installation and Maintenance The
Cisco Internetwork Operating System (Cisco IOS) software executes from Flash memory if a boot helper image...
Hardware Maintenance Manual - Page 37
...31
50
15
Balanced drivers allow EIA/TIA-449 signals to travel a limited distance at any given bit rate; Network Connection Considerations
Serial Connections
When setting up to 64 ...lists the IEEE-recommended maximum speeds and distances for Installation 2-15 If you understand the electrical problems that might arise and can compensate for EIA/TIA-449 shown in the United States, supports...
Hardware Maintenance Manual - Page 44
...
Configuring the Four-Port Serial Module Timing (Clock) Signals All interfaces support both DTE and DCE mode, depending on the mode of error .... Setting the Four-Port Serial Module Clock Rate All DCE interfaces require a noninverted internal transmit clock signal, which is configured to...Cisco 4000 Series Hardware Installation and Maintenance This section describes how to the DCE port.
Hardware Maintenance Manual - Page 45
... command inverts the clock signal to its original phase. For complete command descriptions and instructions, refer to resend the frame. Configuring NRZI Format on all serial interfaces is the factory default on the Four-Port Serial Module All interfaces support both nonreturn to zero (NRZ) and nonreturn to decode signals, rather than determining absolute...
Hardware Maintenance Manual - Page 51
...31.)
Preparing for Installation 2-29 Figure 2-30 4-Port BRI Network Processor Module
PORT-7
PORT-6
PORT...end away from the router first to an Integrated Services Digital Network (ISDN) through an ISDN channel service unit/digital service unit (CSU/DSU) called the NT1. Network Connection Considerations
BRI Connections
The BRI network processor module (see Figure 2-31 and Figure 2-30) supports...
Hardware Maintenance Manual - Page 52
.... This interface is presented to a channel service unit (CSU). The CT1, shown in Table 2-6. Network Connection Considerations
The specifications for the BRI cable are given in Figure 2-32, provides a controller for a remote site.
2-30 Cisco 4000 Series Hardware Installation and Maintenance
For wide-area networking, the CT1 can be configured individually. nF = nanoFarad. On the...
Hardware Maintenance Manual - Page 64
... the BRI module does not support point-to-multipoint configuration, D-channel access procedures are actively transmitting at any cable attached to shut down. Each BRI port is customer owned.
3-6 Cisco 4000 Series Hardware Installation and Maintenance The interrupts generated from the router first to -multipoint wiring configuration. Table 3-1
BRI Cable Specifications
Parameter Resistance...
Hardware Maintenance Manual - Page 127
... you set the software configuration register (bits 3, 2, 1, and 0) to manually boot the system from the console each time you can help initialize the processor hardware and boot the main operating system software. If you set the configuration to 0x0, you will have to zero, you isolate or rule out hardware problems encountered when installing your router. APPENDIX D
Cisco...
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X45-SUP6-E Reviews
We have not received any reviews for Cisco yet.