Cisco CISCO7401-2DC48-RF - 7400 Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO7401-2DC48-RF manuals!
Problems with Cisco CISCO7401-2DC48-RF?
Ask a Question
Free Cisco CISCO7401-2DC48-RF manuals!
Problems with Cisco CISCO7401-2DC48-RF?
Ask a Question
Popular Cisco CISCO7401-2DC48-RF Manual Pages
Configuration Guide - Page 2
... (IP) addresses used in the document are not intended to nexus7k-docfeedback@cisco.com
HE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE...
Configuration Guide - Page 5
...High Availability 3-7 Virtualization Support 3-7 Default Interfaces 3-7 SVI Autostate Exclude 3-7 Licensing Requirements for Layer 2 Port Modes 3-8 Prerequisites for Layer 2 Interfaces 3-8 Guidelines and Limitations 3-8 Default Settings 3-9 Configuring Access ... 4-1 Information About Layer 3 Interfaces 4-1
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
v
Configuration Guide - Page 7
... 6-5 Load Balancing Using Port Channels 6-6 LACP 6-8 Virtualization Support 6-13 High Availability 6-13 Licensing Requirements for Port Channeling 6-14 Prerequisites for Port Channeling 6-14 Guidelines and Limitations 6-14 Default Settings 6-15 Configuring Port Channels 6-15 Creating a Port Channel 6-16
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
vii
Configuration Guide - Page 9
... document comments to nexus7k-docfeedback@cisco.com
Configuring vPC Peer Links and Links to the Core on a Single Module 7-19 vPC Interactions with Other Features 7-20 Virtualization Support 7-27 vPC Recovery After an Outage 7-27 High Availability 7-28 Licensing Requirements for vPCs 7-29 Guidelines and Limitations 7-29 Default Settings 7-30 Configuring vPCs 7-30 Enabling...
Configuration Guide - Page 16
... manual....passwords, are grouped in angle brackets.
[ ]
Default responses to configure IP tunnels using Generic Route Encapsulation (GRE) on the device.
A nonquoted set of code
indicates a comment line.
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide...2 protocol tunneling.
Chapter A, "IETF RFCs supported by vertical bars.
Document Conventions
Command ...
Configuration Guide - Page 17
Cisco currently supports RSS Version 2.0. OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
xvii Preface
Document Conventions
Send document comments to nexus7k-docfeedback@cisco.com
Caution Means reader be delivered directly to be careful. The RSS feeds are a free service. Obtaining Documentation and Submitting a Service Request
For information on ...
Configuration Guide - Page 19
...1-1
Interface Parameters
Feature Basic parameters
Layer 2
Parameters
Further Information
description, duplex, error disable, flow control, MTU, beacon
Chapter 2, "Configuring Basic Interface Parameters" of this document
Layer 2 access and trunk port settings
Chapter 3, "Configuring Layer 2 Interfaces" of this guide but some are covered in this document
Layer 2 MAC, VLANs, private VLANs...
Configuration Guide - Page 52
... use a specific speed, you must set the remote port for the local port. speed {{10 | 100 | 1000 | {auto [10 100 [1000]]}} | {10000 | auto}} 4. duplex {full | half | auto} 5. exit 7. BEFORE YOU BEGIN
Make sure that the remote port has a speed setting that you specify can affect the duplex mode used . Note The interface speed that supports your...
Configuration Guide - Page 132
... VRF unless you in -service software upgrades (ISSUs).
For a complete explanation of BFD packets. For more information, see the Cisco NX-OS Licensing Guide.
By default, Cisco DC-OS places you specifically configure another VDC and VRF. See the "Configuring BFD Support for Routing Protocols" section on page 5-14. • Disable Internet Control Message Protocol (ICMP) redirect...
Configuration Guide - Page 219
... Control (NAC) • Dynamic ARP Inspection (DAI) • IP source guard (IPSG) • Internet Group Management Protocol (IGMP) snooping • Hot Standby Routing Protocol (HSRP) • Protocol Independent Multicast (PIM) • Gateway Load-Balancing Protocol (GLBP) • All routing protocol configurations
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide...
Configuration Guide - Page 223
... need not configure these required matched settings. See the "Compatibility Parameters for ... the vPC peer link.
series modules and LACP, vPC peer link supports 16 LACP interfaces: 8 active ... problems if the STP enhancements are not configured using LACP, you manually configure...With M- See the Cisco Nexus 7000 Series NX-OS Layer 2 Switching Configuration Guide, Release 5.x, for ...
Configuration Guide - Page 225
...supported. In this scenario, the vPC peers use the show spanning-tree command to display information about the vPC, when that the settings... and ipv6 nd synchronize commands to support faster convergence of the Cisco Fabric Service over Ethernet (CFSoE) protocol. If... STP edge ports. (See the Cisco Nexus 7000 Series NX-OS Layer 2 Switching Configuration Guide, Release 5.x, for more information on...
Configuration Guide - Page 228
... displays an error message.
7-26
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03
See the Cisco Nexus 7000 Series NX-OS Unicast Routing Configuration Guide, Release 5.x,...or manually configuring virtual MAC addresses for any FHRP protocol in listen state. For GLBP, the forwarders on both vPC peer devices forward traffic. CFSoE
The Cisco Fabric Services ...
Configuration Guide - Page 230
... completes its backward compatibility support. The second device then performs the upgrade process, locking the first...setting in the startup configuration. The peer
accepts the other protocols.
We recommend that you can configure the Cisco Nexus 7000 Series device to restore vPC services when its peer fails to come online by using the auto-recovery command. Beginning with Cisco...
Configuration Guide - Page 268
...Guide, Release 5.x
8-4
OL-23435-03 Default Settings
Table 8-1 lists the default settings for Cisco NX-OS. • You must be familiar with Cisco NX-OS Release 5.2(5) and for later 5.2(x) releases, you can configure the tunnel interface and the tunnel transport in IETF RFC...8226; Cisco NX-OS does not support WCCP on to the switch. • You have installed the Enterprise Services license ...
Cisco CISCO7401-2DC48-RF Reviews
We have not received any reviews for Cisco yet.