Cisco CISCO7140-2T3-RF - 7140 Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO7140-2T3-RF manuals!
Problems with Cisco CISCO7140-2T3-RF?
Ask a Question
Free Cisco CISCO7140-2T3-RF manuals!
Problems with Cisco CISCO7140-2T3-RF?
Ask a Question
Popular Cisco CISCO7140-2T3-RF Manual Pages
Configuration Guide - Page 6
... document comments to nexus7k-docfeedback@cisco.com
Routed Interfaces 4-2 Subinterfaces 4-2 VLAN Interfaces 4-3 Loopback Interfaces 4-4 Tunnel Interfaces 4-4 High Availability 4-4 Virtualization Support 4-5 Licensing Requirements for Layer 3 Interfaces 4-5 Prerequisites for Layer 3 Interfaces 4-5 Guidelines and Limitations 4-5 Default Settings 4-6 Configuring Layer 3 Interfaces 4-6 Configuring...
Configuration Guide - Page 9
... document comments to nexus7k-docfeedback@cisco.com
Configuring vPC Peer Links and Links to the Core on a Single Module 7-19 vPC Interactions with Other Features 7-20 Virtualization Support 7-27 vPC Recovery After an Outage 7-27 High Availability 7-28 Licensing Requirements for vPCs 7-29 Guidelines and Limitations 7-29 Default Settings 7-30 Configuring vPCs 7-30 Enabling...
Configuration Guide - Page 16
...-OS Interfaces"
lists the IETF RFCs for interfaces supported in Cisco NX-OS Release 4.x
Chapter B, "Configuration Limits for Cisco NX-OS Interfaces"
Lists the Cisco verified limits and maximum limits for which you supply values are in italic screen font.
< >
Nonprinting characters, such as passwords, are in angle brackets.
[ ]
Default responses to configure IP tunnels using...
Configuration Guide - Page 17
The RSS feeds are a free service. Cisco currently supports RSS Version 2.0. In this situation, you might do something that could result in Cisco Product Documentation as an RSS feed and set content to your desktop using a reader application.
Preface
Document Conventions
Send document comments to nexus7k-docfeedback@cisco.com
Caution Means reader be delivered directly to be...
Configuration Guide - Page 19
...error disable, flow control, MTU, beacon
Chapter 2, "Configuring Basic Interface Parameters" of this document
Layer 2 access and trunk port settings
Chapter 3, "Configuring Layer 2 Interfaces" of the interface types supported...
Information About Interfaces
Cisco NX-OS supports multiple configuration parameters for an interface.
Table 1-1 shows where to nexus7k-docfeedback@cisco.com
1 C ...
Configuration Guide - Page 23
...can create multiple virtual device contexts (VDCs). Licensing Requirements for Interfaces
Interfaces support stateful and stateless restarts. OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
1-5 High Availability for Interfaces
IP tunnels and vPCs require the Enterprise Services license. Once an interface is an independent logical device to which you...
Configuration Guide - Page 37
...Cisco-supported transceivers, use Cisco-supported transceivers. To send pause frames when you decide to configure the port speed and duplex modes manually for a local port, consider the following:
- To prevent the sending of speeds and duplex modes that the remote port send parameter is configured, set... command.
• When configuring flow control for these ports, consider the following:...
Configuration Guide - Page 52
... Interfaces Configuration Guide, Release 5.x
OL-23435-03 Note The interface speed that supports your changes for autonegotiation, the duplex mode is automatically set the speed before setting the duplex mode. interface interface 3. speed {{10 | 100 | 1000 | {auto [10 100 [1000]]}} | {10000 | auto}} 4. BEFORE YOU BEGIN
Make sure that the remote port has a speed setting that you...
Configuration Guide - Page 131
...support BFD. Note The BFD failure detection occurs in the actual forwarding of BFD control packets that connect to the individual modules that are sent between two BFD neighbors. BFD Echo Function
The BFD echo function sends echo packets from the forwarding engine to nexus7k-docfeedback@cisco...than a second, which is without involving the remote system, so there is no longer reachable ...
Configuration Guide - Page 132
...). Any feature not included in the
default VDC. • See other detailed prerequisites that are listed with Cisco NX-OS Release 5.2, you in -service software upgrades (ISSUs). For the echo response packet, BFD sets the TTL value to the BFD peers. Virtualization Support
BFD supports virtual routing and forwarding instances (VRFs). For more information, see the...
Configuration Guide - Page 203
... interfaces on the M series modules for all vPC member ports on the physical switch. See the Cisco NX-OS FCoE Configuration Guide for Cisco Nexus 7000 and Cisco MDS 9500 for Configuring vPCs, page 7-60
Note For information about configuring port channels and the Link Aggregation Control Protocol (LACP), see the Cisco Nexus 7000 Series NX-OS...
Configuration Guide - Page 223
... type so that you need not configure these required matched settings. See the "Compatibility Parameters for information about these . OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
7-21
With F-Series line-cards, vPC peer link and downstream vPC channels support upto 16 active LACP links. If the vPC peer...
Configuration Guide - Page 225
... the other half to ensure that the settings are sent from the STP computation. The access switch traffic is not supported.
You can lose traffic. Note We recommend that you configure the ports on networks that feature is excluded from both sides of the Cisco Fabric Service over Ethernet (CFSoE) protocol. You should configure...
Configuration Guide - Page 228
... converged before the vPC is not supported on FHRPs and routing. CFSoE
The Cisco Fabric Services over to the secondary vPC peer ...-in MAC address option (use-bia) for HSRP or manually configuring virtual MAC addresses for any FHRP protocol in CFS...the system displays an error message.
7-26
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 You can use...
Configuration Guide - Page 283
... edge ports.
• Dot1x tunneling is not supported.
• You should perform an EPLD upgrade to newer versions in these deployments.
• You must manually configure the 802.1Q interfaces to be identified in a license package is bundled with the Cisco NX-OS system images and is not supported.
• You should use MAC address...
Cisco CISCO7140-2T3-RF Reviews
We have not received any reviews for Cisco yet.