Cisco CISCO7120-4T1 - 7120 Router Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco CISCO7120-4T1 manuals!
Problems with Cisco CISCO7120-4T1?
Ask a Question
Free Cisco CISCO7120-4T1 manuals!
Problems with Cisco CISCO7120-4T1?
Ask a Question
Popular Cisco CISCO7120-4T1 Manual Pages
Configuration Guide - Page 16
...Encapsulation (GRE) on the device. Elements in brackets and separated by Cisco NX-OS Interfaces"
lists the IETF RFCs for interfaces supported in boldface.
Optional alternative keywords are grouped in square brackets are in square brackets.
!, #
An exclamation point (!) or a pound sign (#) at the beginning of a line of characters. A nonquoted set of code
indicates a comment line.
Configuration Guide - Page 52
...autonegotiation, the duplex mode is automatically set the speed before setting the duplex mode. copy running-config startup-config
2-28
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 Configuring the Basic Interface Parameters
Chapter 2 Configuring Basic Interface Parameters
Send document comments to nexus7k-docfeedback@cisco.com
switch(config-if)# link...
Configuration Guide - Page 60
....
(Optional) Copies the running configuration to configure, and enters interface configuration mode.
Specifies an interface to the startup configuration.
2-36
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 copy running -config startup-config
Purpose Enters configuration mode. You can set an informational value range between 1 and 16777215, where...
Configuration Guide - Page 78
... the parameter values.
Verifying the Basic Interface Parameters
Chapter 2 Configuring Basic Interface Parameters
Send document comments to nexus7k-docfeedback@cisco.com
Verifying the Basic Interface Parameters
You can set up to the VDC that reach the supervisor
module on interfaces.
2-54
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 Note The...
Configuration Guide - Page 112
... received by this interface. High Availability
Layer 3 interfaces support stateful and stateless restarts. See the Cisco Nexus 7000 Series NX-OS High Availability and Redundancy Guide, Release 5.x, for complete information on IP tunnels.
Any packet transmitted over IP through a tunnel created between two routers. Loopback interfaces can use loopback interfaces for more information...
Configuration Guide - Page 114
... 3 mode.
• Layer 3 router interfaces and sub-interfaces can configure any Ethernet port as a routed interface. Default Settings
Table 4-1 lists the default settings for this feature might differ from the Cisco IOS commands that you are in the correct VDC (or use . Only direct route is supported.
Default Settings
Chapter 4 Configuring Layer 3 Interfaces
Send document comments to...
Configuration Guide - Page 121
...-if)# copy running -config startup-config
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
4-13 Brings an interface administratively up (enable/disable an interface).
Chapter 4 Configuring Layer 3 Interfaces
Configuring Layer 3 Interfaces
Send document comments to nexus7k-docfeedback@cisco.com
DETAILED STEPS
Step 1
Command
configure terminal
Step...
Configuration Guide - Page 123
SUMMARY STEPS
1. interface interface-type number 3. Enters interface configuration mode. You must do this interface to a VRF.
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
4-15
Configures an IP address for a tunnel interface after you are in the correct VDC (or use the switchto vdc command). BEFORE YOU BEGIN Ensure that you assign this...
Configuration Guide - Page 134
...are sent with BFD. Default Settings
Chapter 5 Configuring Bidirectional Forwarding Detection
Send document comments to nexus7k-docfeedback@cisco.com
Note Using BFD per ...mode and sub-interface optimization simultaneously on Subinterfaces, page 5-13 • Configuring BFD Support for Routing Protocols, page 5-14
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
5-6...
Configuration Guide - Page 142
... you are in the correct VDC (or use the switchto vdc command).
The default is supported on a BFD-enabled interface.
See the "Enabling the BFD Feature" section on BGP, page 5-15
5-14
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03
configure terminal 2. Configure the BFD session parameters. See the "Configuring...
Configuration Guide - Page 146
...-router)#
bfd
Step 4
Example: switch(config-router)# bfd
interface int-if
Step 5
Example: switch(config-router)# interface ethernet 2/1 switch(config-if)#
ip ospf bfd
Example: switch(config-if)# ip ospf 201 bfd
Purpose Enters configuration mode. See the "Enabling the BFD Feature" section on page 5-9. See the Cisco Nexus 7000 Series NX-OS Unicast Routing Configuration Guide...
Configuration Guide - Page 148
...alphanumeric string up to display the supported interfaces.
(Optional) Enables or disables BFD on the standby HSRP router detects that you are in the...interfaces 3. The show hsrp detail will show running-config hsrp 6. (Optional) copy running-config startup-config
5-20
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 The active and standby HSRP routers...
Configuration Guide - Page 161
...interfaces configured with the channel mode set to on an individual member port. For example, you cannot add a Layer 3 interface to see the full list of operational attributes for an interface before allowing that interface... capability • Flow-control configuration
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
6-5 You can force ports with the...
Configuration Guide - Page 162
...• Service policy • Access control lists (ACLs) Many interface parameters remain unaffected when the interface joins or ...sets all operational interfaces in a port channel by default.
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
6-6
OL-23435-03 Load Balancing Using Port Channels
The Cisco DC-OS software load balances traffic across all member interfaces...
Configuration Guide - Page 295
... Guide, Release 5.x
A-1 Title Path MTU Discovery for IP version 6 IP Version 6 Addressing Architecture An Aggregatable Global Unicast Address Format Internet Protocol, Version 6 (IPv6) Specification Neighbor Discovery for IP Version 6 (IPv6) IPv6 Stateless Address Autoconfiguration Internet Control Message Protocol (ICMPv6) for interfaces supported by Cisco NX-OS Interfaces
IPv6 RFCs
RFCs RFC...
Cisco CISCO7120-4T1 Reviews
Do you have an experience with the Cisco CISCO7120-4T1 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!