Cisco CISCO7120-SMI3 - 7120 Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO7120-SMI3 manuals!
Problems with Cisco CISCO7120-SMI3?
Ask a Question
Free Cisco CISCO7120-SMI3 manuals!
Problems with Cisco CISCO7120-SMI3?
Ask a Question
Popular Cisco CISCO7120-SMI3 Manual Pages
Configuration Guide - Page 9
... document comments to nexus7k-docfeedback@cisco.com
Configuring vPC Peer Links and Links to the Core on a Single Module 7-19 vPC Interactions with Other Features 7-20 Virtualization Support 7-27 vPC Recovery After an Outage 7-27 High Availability 7-28 Licensing Requirements for vPCs 7-29 Guidelines and Limitations 7-29 Default Settings 7-30 Configuring vPCs 7-30...
Configuration Guide - Page 16
...or references to configure IEEE 802.1Q-in-Q (Q-in the manual. Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
xvi
OL-23435-03
Arguments for which you must...@cisco.com
Chapter
Description
Chapter 8, "Configuring IP Tunnels"
Describes how to system prompts are in screen font. A nonquoted set of code
indicates a comment line.
Chapter A, "IETF RFCs supported ...
Configuration Guide - Page 17
... might do something that could result in Cisco Product Documentation as an RSS feed and set content to be delivered directly to nexus7k-docfeedback@cisco.com
Caution Means reader be careful.
The RSS feeds are a free service. OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
xvii Preface
Document Conventions
Send document...
Configuration Guide - Page 37
... the port speed and duplex modes manually for example, 10, 100, or 1000 Mb/s), you do not know that can change a Layer 3 interface into a Layer 3 interface by using Cisco-supported transceivers, use Cisco-supported transceivers. If you set the local port send parameter to negotiate the speed. Do not configure the connecting port to desired.
- To send...
Configuration Guide - Page 52
...supports your changes for an interface, so you should configure both of their parameters at the same time. exit 7. If you set the speed for autonegotiation, the duplex mode is automatically configured to use a specific speed, you must set...config startup-config
2-28
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 If you want to set the local port to ...
Configuration Guide - Page 167
...Static Port Channels
Enable globally
Not applicable
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
6-11 LACP Port Priority
Each port that...mode. The software supports only Marker Responders. Chapter 6 Configuring Port Channels
Information About Port Channels
Send document comments to nexus7k-docfeedback@cisco.com
Note The LACP system ID is the ...
Configuration Guide - Page 168
...LACP port channels, but the feature is connected to a non-Nexus peer, its graceful ... manageable interface. When the Cisco Nexus 7000 Series device is not operational.
6-12
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-... issues and to assist with LACP port channels.
By default, LACP sets a port to the suspended state if it can cause servers to ...
Configuration Guide - Page 221
...list.
You use this new vPC primary device until the system stabilizes. This action forces the vPC secondary device to take ...connect to the downstream device, you create a port channel to the downstream device from the secondary peer device. Create a track list that contains all the interfaces in the track list below. See the Cisco Nexus 7000 Series NX-OS Unicast Routing Configuration Guide...
Configuration Guide - Page 223
... Configuration Guide, Release 5.x
7-21 You can have only 8 links in the STP active topology.
series modules and LACP, vPC peer link supports 16 LACP interfaces: 8 active links and 8 hot standby links. We recommend that you set all the vPC peer link interfaces to the STP network port type so that you manually configure the system...
Configuration Guide - Page 228
...CFSoE
The Cisco Fabric Services over IP ...for HSRP or manually configuring virtual MAC ...system displays an error message.
7-26
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide..., Release 5.x
OL-23435-03 You can configure lower and upper thresholds to work correctly on a vPC peer link is not supported...
Configuration Guide - Page 230
... high-availability features.
7-28
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 Beginning with Cisco NX-OS Release 5.0(2), you can configure the Cisco Nexus 7000 Series device to restore vPC services when its peer fails to be running different releases of Cisco NX-OS, however the system functions correctly because of its...
Configuration Guide - Page 246
...
Manually Configuring the System Priority
When you are the primary devices on both vPC peer devices. Example: switch(config-vpc-domain)# exit switch(config)#
7-44
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03
SUMMARY STEPS
1. vpc domain domain-id 3.
The range of values is 32667.
system-priority priority
Example: switch...
Configuration Guide - Page 267
... about VDCs and see the Cisco NX-OS Licensing Guide.
You can be in the...Support
You can receive ICMP messages generated by dynamically determining the lowest MTU along the path from a tunnel with Cisco NX-OS Release 4.2, you specifically configure another VDC. This VRF should be received before using PMTUD over firewall connections. For a complete explanation of the Cisco...
Configuration Guide - Page 268
....
• For Cisco NX-OS Release 5.0(1) and later, the maximum number of supported tunnel interfaces was changed to 4095.
• Cisco NX-OS does not support WCCP on to a Tunnel Interface, page 8-8
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
8-4
OL-23435-03 Guidelines and Limitations
IP tunnels have installed the Enterprise Services license for IP...
Configuration Guide - Page 283
...some Cisco Nexus devices. Any feature not included in a license package is bundled with the Cisco NX-OS system images...are not required in these deployments.
• You must manually configure the 802.1Q interfaces to be edge ports.
...service-provider network must be routed.
• Cisco Nexus 7000 Series devices can provide only MAC-layer ACL/QoS for Q-in-Q tagged packets is not supported...
Cisco CISCO7120-SMI3 Reviews
We have not received any reviews for Cisco yet.