Cisco CISCO7120-E3 - 7120 Router Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco CISCO7120-E3 manuals!
Problems with Cisco CISCO7120-E3?
Ask a Question
Free Cisco CISCO7120-E3 manuals!
Problems with Cisco CISCO7120-E3?
Ask a Question
Popular Cisco CISCO7120-E3 Manual Pages
Configuration Guide - Page 2
... Series NX-OS Interfaces Configuration Guide, Release 5.x © 2009-2011 Cisco Systems, Inc. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS...
Configuration Guide - Page 52
...
Send document comments to nexus7k-docfeedback@cisco.com
switch(config-if)# link debounce time 0 switch(config-if)#
Configuring the Interface Speed and Duplex Mode
The interface speed and duplex mode are interrelated, so you should set the speed before setting the duplex mode.
SUMMARY STEPS
1. Note The interface speed that supports your changes for Ethernet and management...
Configuration Guide - Page 60
... the running -config startup-config
Purpose Enters configuration mode. delay value 4. You can set an informational value range between 1 and 16777215, where the value represents the number of tens of microseconds. SUMMARY STEPS
1. exit 6.
interface ethernet slot/port 3. Specifies an interface to nexus7k-docfeedback@cisco.com
Configuring the Throughput Delay
You can configure the...
Configuration Guide - Page 78
...
Displays the UDLD status for statistics collections on a specific interface.
show interface interface
Displays the configured states of one of interface states.
show udld-global
Displays the UDLD status for packets that reach the supervisor
module on interfaces.
2-54
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 You can display and...
Configuration Guide - Page 112
...tunnel created between two routers. Loopback interfaces can act as IP tunnels.
You can configure up even if some of the outbound interfaces are down. High Availability
Layer 3 interfaces support stateful and stateless restarts. After the switchover, Cisco NX-OS applies the runtime configuration after the switchover. Tunnel Interfaces
Cisco NX-OS supports tunnel interfaces as a termination...
Configuration Guide - Page 114
... to both of the supported connectivity cases:
- SVI with the Cisco IOS CLI, be configured on an Interface, page 4-9 • Configuring a VLAN interface, page 4-10 • Configuring Inband Management in Layer 3 mode.
• Layer 3 router interfaces and sub-interfaces can configure any Ethernet port as a routed interface. Table 4-1
Default Layer 3 Interface Parameters
Parameters Admin...
Configuration Guide - Page 121
...
Step 8
Example: switch(config-if)# show interface vlan 10
copy running-config startup-config
Example: switch(config-if)# copy running -config startup-config
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
4-13 Note Configure the VLAN and add the interfaces.
Creates a loopback interface. See the Cisco Nexus 7000 Series NX-OS Unicast...
Configuration Guide - Page 123
.... You must do this step after you are in the correct VDC (or use the switchto vdc command). vrf member vrf-name 4.
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
4-15
Configuration Guide - Page 134
... • Configuring BFD Support for Routing Protocols, page 5-14
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
5-6
OL-23435-03 HSRP for BFD packets are sent with BFD.
The DSCP/COS values for IPv6 is supported with COS 6/DSCP
CS6. Default Settings
Table 5-1 lists the default settings for BFD parameters. Default Settings
Chapter 5 Configuring Bidirectional...
Configuration Guide - Page 142
... in the correct VDC (or use the switchto vdc command). keyword to another Cisco NX-OS device. Configure the BFD session parameters. interface int-if 3.
The default is supported on BGP, page 5-15
5-14
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 See the "Configuring Global BFD Parameters" section on page...
Configuration Guide - Page 146
...-router)# interface ethernet 2/1 switch(config-if)#
ip ospf bfd
Example: switch(config-if)# ip ospf 201 bfd
Purpose Enters configuration mode. Configuring BFD
Chapter 5 Configuring Bidirectional Forwarding Detection
Send document comments to nexus7k-docfeedback@cisco.com
Configuring BFD on OSPF
You can be any case-sensitive, alphanumeric string up to display the supported interfaces...
Configuration Guide - Page 148
...-router)# bfd interface int-if
Example: switch(config-router)# interface ethernet 2/1 switch(config-if)# isis bfd
Example: switch(config-if)# isis bfd show running-config hsrp 6. (Optional) copy running -config startup-config
Enters interface configuration mode. Use the ?
See the Cisco Nexus 7000 Series NX-OS Unicast Routing Configuration Guide, Release 5.x, for all -interfaces...
Configuration Guide - Page 161
...interfaces configured with the channel mode set to on an individual member port. You can force ports with the channel mode as active or passive to port channels that the Cisco... • Flow-control capability • Flow-control configuration
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
6-5 If you configure a member port with the channel group...
Configuration Guide - Page 162
...port-channel interface and remove a member port from the port channel. Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release ...8226; NAC • Service policy • Access control lists (ACLs) Many interface parameters remain unaffected when the interface joins or leaves a ...you delete the port channel, the software sets all operational interfaces in a port channel by default. ...
Configuration Guide - Page 223
...set all the vPC peer link interfaces to the STP network port type so that you first bring up . See the Cisco Nexus 7000 Series NX-OS Layer 2 Switching Configuration Guide...supports 16 LACP interfaces: 8 active links and 8 hot standby links. With M-
With F-Series line-cards, vPC peer link and downstream vPC channels support...failures.
Note When manually configuring the system ...
Cisco CISCO7120-E3 Reviews
Do you have an experience with the Cisco CISCO7120-E3 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!