Cisco CISCO2523CF - 2523CF Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO2523CF manuals!
Problems with Cisco CISCO2523CF?
Ask a Question
Free Cisco CISCO2523CF manuals!
Problems with Cisco CISCO2523CF?
Ask a Question
Popular Cisco CISCO2523CF Manual Pages
Getting Started Guide - Page 3
... disposal of a suitably installed ground conductor. Introduction to the Controller
The 2504 controller works in increments of 5 access points with Cisco lightweight access points and the Cisco Wireless Control System (WCS) to 50 lightweight access points in conjunction with a minimum of services for mobility services such as voice and video, and OEAP support for retail, enterprise...
Getting Started Guide - Page 4
...system connection
LAN link for management software connections
WAN or LAN connection to Cisco 2500 Series Wireless Controllers are not currently supported. Figure 1 shows a 2504 controller network topology and network connections....11n with Cisco Next-Generation Wireless Solutions and Cisco Enterprise Wireless Mesh. The controller has an auto MDI feature, so you can use this guide, you should...
Getting Started Guide - Page 5
...of the allowed values before setting the baud rate. Figure 2 Front Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4...setting matches one of the LED manufacturer's specifications and is detected the baud rate will be small variations in LED color intensity and hue from unit to 9600.
5 however the bootloader ensures that supports...
Getting Started Guide - Page 6
... only ports; This port is designed so that 1500 VAC rms
isolation (per the 802.3 specification) is an RJ-45 connector
form-factor. The POE controller reset is an RJ-45 connector
form-factor. This interface supports the proper voltage isolation as defined by 802.3. LED description:
• Green or Blinking Green...
Getting Started Guide - Page 9
... the Controller for Operation
Follow these steps to connect CLI console and controller
9
Required Tools and Information...install the controller: • Wireless controller hardware - If any item is damaged or missing, notify your authorized Cisco sales representative.
Return all items listed in the "Package Contents" section are included in the shipment. Network, operating system service...
Getting Started Guide - Page 10
Cisco uses an integral TFTP server.
The system name can contain up to 32 printable ASCII characters.
• An administrative username and password...well for downloading operating system software updates). This means that ...router IP address, such as controller. Initial System Configuration Information
Obtain the following initial configuration parameters from clients, either Yes or No.
-
Getting Started Guide - Page 13
...openings to the system. Note Allow ... installation.
The kit part number...installation:
• Connecting the Controller Console Port • Securing the Power Adapter Cable • Connecting to the Network
For configuration instructions about using rack-mount brackets, follow the correct procedures could result in the kit.
13 Step 3 Place the switch on a wall using the CLI setup...
Getting Started Guide - Page 24
... display example:
CISCO SYSTEMS WLCNG Boot Loader Version 1.0.15 (Built on Nov 23 2010 at 07:51:36 by cisco) Board Revision ...displays operating system software initialization (code download and POST verification) and basic configuration as shown in the following menu
Boot Loader Menu
1. Manually update images ...Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU - OK.
Getting Started Guide - Page 25
...Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services...build 269. Installing ether-pow driver - 0x6008 starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar' Cryptographic library self-test....passed! Num of Cisco Systems, Inc. ...
Getting Started Guide - Page 27
...: No such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. Active 2. Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1. Change active boot image 4. Format FLASH Drive 6. Installing ether-pow driver - 0x6008 starting pid 672, tty '': '/etc/init...
Getting Started Guide - Page 28
...Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services... AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok...
Getting Started Guide - Page 30
... Router Management Interface VLAN Identifier
Management Interface Port Num [1 to 4]
Note There is the name you want to assign to this controller.
Enter the IP address of the access point manager interface.
Note Press the hyphen key if you must enter a password. Table 3
Startup Wizard Information
Wizard Setting System Name Administrative user name
Administrative password...
Getting Started Guide - Page 31
...support mobility management, DHCP relay, and embedded Layer 3 security such as 1.1.1.1.
Values are usually also in an RF group are yes or no.
However, a mobility group facilitates scalable, system-wide mobility and controller redundancy while an RF group facilitates scalable, system-wide dynamic RF management. Network Name (SSID)
Enter the network name, or service set...and VPN ...
Getting Started Guide - Page 34
...) to 160 minutes using double quotation marks. Figure 13 External Network Equipment Connection to the Controller
10/100/1000BASE-T MDI cable
Cisco Access Points
CLI console
Connection to CISCO2504, enter config prompt "CISCO2504" and press Enter. You can change the system prompt to main office
Network
34
Firewall
Office network
10/100/1000BASE-T MDI...
Getting Started Guide - Page 35
... system) as the controller is operational, the controller is available to associate. Note Direct connection of...supported. Note If the link does not activate, check the cable. Connecting Access Points
After you have prepared the controller for information on configuring the controller to meet the specific needs of access points to the Cisco Wireless LAN Controller Configuration Guide...
Cisco CISCO2523CF Reviews
We have not received any reviews for Cisco yet.