Cisco 2516 Support and Manuals
Popular Cisco 2516 Manual Pages
Getting Started Guide - Page 5
...
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4
PWR SYS ALM
RESET
1 2 3-4 POE
PWR ALM
SYS
Table 1 Callout
WLC2504 Front Panel Component Descriptions
Port and LEDs
State and Description
CONSOLE CPU console port
The CPU console port is an RS-232 port that the stored baud rate setting matches one of the LED manufacturer's specifications...
Getting Started Guide - Page 9
... access point cables as required • Command-line interface (CLI) console -
Return all items listed in the "Package Contents" section are included in the shipment. Required Tools and Information
You will need the following items: • One Cisco 2504 Wireless Controller. • One Power supply and power cord (power cord option configurable). • Cisco...
Getting Started Guide - Page 11
.... This guide is available at least 4 in a secure equipment room or wiring closet.
Leave at cisco.com.
...configuring a RADIUS server, such as 10.40.0.3, 1812, and mysecretcode.
• The country code for country code information. Choosing a Physical Location
You can reach a 100 to 240 VAC grounded electrical outlet.
3 Installing the Controller
This section includes the following installation...
Getting Started Guide - Page 21
... PC terminal emulation program.
To connect the PC to the 2504 controller, use the plastic relief clip shipped with a 2504 controller.
To secure the power adapter cable and plug, follow these steps:
21 Doing so will damage the controller. Caution
If the relief clip is not installed, the power connector can configure the...
Getting Started Guide - Page 24
... done Network: octeth0', octeth1, octeth2, octeth3
' - OK. Run primary image (7.0.114.76) - Type: Hard Disk - Format FLASH Drive 6. Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to three minutes. Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU - Run backup image (7.0.114.75) 3.
Getting Started Guide - Page 25
... Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok
25 Flags-[DUTY CYCLE] : ok Fastpath CPU00: Initializing last packet received queue. Cisco AireOS Version 7.0.114.76 Firmware Version...
Getting Started Guide - Page 26
... interrupt the boot process and access the Boot menu.
26 Starting Policy Manager: ok Starting Authentication Engine: ok Starting Mobility Management: ok Starting Virtual AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature...
Getting Started Guide - Page 27
... (7.0.114.76) 100% 31427987 bytes read Launching images... Software Copyright Cisco Systems, Inc. Run backup image (7.0.114.75) 3. Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1. XML config selected Validating XML configuration octeon_device_init: found 1 DPs /dev/fpga: No such device or...
Getting Started Guide - Page 28
...: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security...
Getting Started Guide - Page 30
...connectivity to match the switch interface configuration. Enter the administrative password to be set to enterprise services such as AAA servers.
You can access the controller GUI interface using the... the default router. You can enter up to this controller.
Table 3
Startup Wizard Information
Wizard Setting System Name Administrative user name
Administrative password
Action
Enter ...
Getting Started Guide - Page 31
...server.
Configure DHCP Bridging Mode
Enter yes to both the mobility group and the RF group, these groups are yes or no.
You should enter a fictitious, unassigned IP address, such as guest web authentication and VPN termination. Network Name (SSID)
Enter the network name, or service set... SSID that you want the controller to support mobility management, DHCP relay, and embedded ...
Getting Started Guide - Page 32
... following :
• RADIUS server IP address
• RADIUS server port (default port is the United States (US). Enter Country Code List Enable 802.11b Network Enable 802.11a Network Enable 802.11g Network Enable Auto-RF Configure a NTP server now?
Table 3
Startup Wizard Information (continued)
Wizard Setting Allow Static IP Addresses
Configure a RADIUS Server Now?
The default is...
Getting Started Guide - Page 33
....
33 Configuration correct? the controller saves your configuration, reboots, and prompts you created in the startup wizard are yes and no. Table 3
Startup Wizard Information (continued)
Wizard Setting
Enter a...Enter a valid username and password to log into the controller CLI. Note The administrative username and password you to log in the "Configure a NTP Server Now?" Enter yes if the...
Getting Started Guide - Page 35
...35 You have configured the controller, use a straight-through ) to Cisco 2500 Series Wireless Controllers are not currently
supported. Refer to the Cisco Wireless LAN Controller Configuration Guide for information on configuring the controller to a hub or a switch, use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the...
Getting Started Guide - Page 37
... and loads the configuration. Step 2 Step 3
Press and hold the Reset button for at : http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to your username and password at the prompts.
After the controller reboots, enter your desktop using a pointed object, such as a Really Simple Syndication (RSS) feed and set content to...
Cisco 2516 Reviews
Do you have an experience with the Cisco 2516 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!