Cisco 2513 Support and Manuals
Popular Cisco 2513 Manual Pages
Getting Started Guide - Page 3
... and regulations.
Replace the battery only with four 4 Gigabit Ethernet ports.
3 Statement 1040
Safety Considerations
• Verify that the ambient temperature remains between wireless access points and other devices to the manufacturer's instructions. Statement 1024
Warning
Ultimate disposal of services for mobility services such as voice and video, and OEAP support for retail...
Getting Started Guide - Page 4
... management software connections
WAN or LAN connection to Cisco 2500 Series Wireless Controllers are not currently supported. The 2504 controller offers robust coverage with 802.11 a/b/g and delivers unprecedented reliability using 802.11n with Cisco Next-Generation Wireless Solutions and Cisco Enterprise Wireless Mesh.
To best use this guide, you can use straight-through or crossover...
Getting Started Guide - Page 5
... Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4
PWR SYS ALM
RESET
1 2 3-4 POE
PWR ALM
SYS
Table 1 Callout
WLC2504 Front Panel Component Descriptions
Port and LEDs
State and Description
CONSOLE CPU console port
The CPU console port is an RS-232 port that the stored baud rate setting matches one of 1200, 2400, 4800...
Getting Started Guide - Page 6
... rms
isolation (per the 802.3 specification) is an RJ-45 connector
form-factor.
If software needs to I2C address 0x40/41 (0100 000r/w). Callout
Port and LEDs
State and Description
1
GigE port and LED
The Gigabit Ethernet port is met between
chassis ground and any 48V/Ethernet signal. This interface supports the proper voltage isolation as defined...
Getting Started Guide - Page 9
...hardware will be included, if selected.
VT-100 terminal emulator on controller at factory, if selected. ...Cisco 2504 Wireless Controller software pre-loaded on the controller (software option configurable). • Optional licenses will be pre-installed on CLI console (PC, laptop, or palmtop) -
Network, operating system service network, and access point cables as required • Command...
Getting Started Guide - Page 21
...Port
Caution
Do not connect a Power over Ethernet (PoE) cable to a PC that uses a VT-100 terminal emulator (such as HyperTerminal, ProComm, Minicom, or Tip). Start the PC terminal emulation program.
Caution
If the relief clip is not installed... The clip relieves the cable in the event it to the console port. Note The Cisco 2106 power adapter is pulled or if the power adapter falls. To ...
Getting Started Guide - Page 24
... at 07:51:36 by cisco) Board Revision 0.0 (SN: PSJ143302MT, Type: AIR-CT2504-K9) (P) Verifying boot loader integrity... Active 2. Clear configuration 5. Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to access the Boot Menu... Do not reboot the controller until the user login prompt appears.
Getting Started Guide - Page 25
...build 269. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP...
Getting Started Guide - Page 26
...: ok Starting CIDS Services: ok Starting Ethernet-over-IP: ok Starting DTLS server: enabled in CAPWAP Starting CleanAir: ok Starting WIPS: ok Starting SSHPM LSC PROV LIST: ok Starting RRC Services: ok Starting FMC HS: ok Starting Management Services:
Web Server: ok CLI: ok
Secure Web: Web Authentication Certificate not found (error). License Agent: ok
(Cisco Controller)>
Step...
Getting Started Guide - Page 27
... of Cisco Systems, Inc. Active 2. Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1.
All rights reserved. Run primary image (7.0.114.76) - Loading primary image (7.0.114.76) 100% 31427987 bytes read Launching images... Do not reboot the controller until the user...
Getting Started Guide - Page 28
...: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting Power Supply and Fan Status Monitoring Service: ok Starting Mesh Services: ok Starting TSM: ok Starting CIDS Services: ok Starting Ethernet-over-IP: ok Starting...
Getting Started Guide - Page 30
... password, you must enter a password.
Enter the IP address of the access point manager interface. Enter the port number of the management interface netmask. You can enter up to match the switch interface configuration. Enter the administrative user name to be assigned to 4.
30
Enter the IP address of the controller and connectivity to the previous command...
Getting Started Guide - Page 34
... 10/100/1000BASE-T Ethernet (RJ-45 physical port, UTP, Category-5 or higher cable). Note
The CLI automatically logs out without saving any alphanumeric string up to CISCO2504, enter config prompt "CISCO2504" and press Enter.
Figure 13 External Network Equipment Connection to the Controller
10/100/1000BASE-T MDI cable
Cisco Access Points
CLI console
Connection...
Getting Started Guide - Page 35
...
After you have prepared the controller for information on configuring the controller to meet the specific needs of access points to Cisco 2500 Series Wireless Controllers are connecting to a hub or a switch, use a straight-through ) to connect access that are scanning for a controller. You have configured the controller, use an MDI-X or MDI cable (crossover or...
Getting Started Guide - Page 37
..., and gathering additional information, see the monthly What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your username and password at the prompts. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
37 After the controller reboots, enter your desktop using a pointed...
Cisco 2513 Reviews
Do you have an experience with the Cisco 2513 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!