Cisco ESR10008 - 10000 Modular Expansion Base Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco ESR10008 manuals!
Problems with Cisco ESR10008?
Ask a Question
Free Cisco ESR10008 manuals!
Problems with Cisco ESR10008?
Ask a Question
Popular Cisco ESR10008 Manual Pages
Hardware Installation Guide - Page 4
... Connections 2-6 Setting Up Fiber-Optic Connections 2-7 Interference Considerations 2-7 Rack-Mounting and Location Guidelines 2-8 Rack Selection Guidelines 2-8 Rack Configuration Guidelines 2-8 Rack Placement Guidelines 2-9 Site Planning Checklist 2-11
Safety 2-11
Preventing Electrostatic Discharge Damage 2-12
Electrical Safety 2-13 Receiving the Cisco 10000 Series Router 2-14
Chassis-Lifting...
Hardware Installation Guide - Page 5
... the Configuration File 4-8 Relocating the Configuration to a Flash Disk 4-9 Managing System Boot Parameters 4-9 Changing the Configuration Register Settings 4-10 Configuration Register Settings 4-10 Predeployment Testing 4-11 Troubleshooting Installation Problems 4-12 General Troubleshooting Tips 4-12 Troubleshooting Ethernet Connections 4-13
Cisco 10008 Router Hardware Installation Guide
v
Hardware Installation Guide - Page 29
...the Cisco 10008 router chassis.
OL-0659-13
Cisco 10008 Router Hardware Installation Guide
2-3 For additional information about floor loading requirements, consult the document GR-63-CORE, Network Equipment Building System (NEBS) Requirements: Physical Protection. Chapter 2 Preparing for Installation
Site Planning
Table 2-2
Heat Dissipation of Cisco 10000 Series Router
Chassis Type Cisco...
Hardware Installation Guide - Page 30
...bond fastening hardware should be made with a 6-AWG, copper ground conductor at a minimum. Electrical Service Requirements
The building's electrical wiring supplying power to the Cisco 10008 series router must comply with all applicable codes and is approved for AC and DC powered systems.
AC Powered Systems
The Cisco 10008 router chassis' AC PEM uses a short power cord with a male IEC 320 C20...
Hardware Installation Guide - Page 39
...; Disconnect all power and external cables before installing or removing a chassis. • Do not work area for the room in wet locations unless the jack is disconnected from a circuit; In addition, use the guidelines that power has been disconnected from a power source but is still connected to the system. OL-0659-13
Cisco 10008 Router Hardware Installation Guide
2-13
Hardware Installation Guide - Page 54
... and top/rear sides of the chassis to install and replace FRUs, or to access network cables and equipment. • The Cisco 10008 router needs adequate ventilation. Use the following : • The Cisco 10008 router requires at least 3 inches (7.62 cm) of clearance at the front and rear of the chassis). • The Cisco 10008 router should be installed off the floor. Warning Two people...
Hardware Installation Guide - Page 55
..., and any AC powered installation where compliance with Telcordia (formerly Bellcore) grounding requirements is shipped assembled. Contact the appropriate electrical inspection authority or an electrician if you are tight. Chapter 3 Installing the Cisco 10008 Router
Connecting the Chassis to Ground
Note The cable management bracket consists of two pieces (the cable guide and channel...
Hardware Installation Guide - Page 57
... lug
OL-0659-13
Cisco 10008 Router Hardware Installation Guide
3-15
Figure 3-13
Attaching Grounding Wire to the wire (Figure 3-13).
Insert the stripped end of the grounding wire into the open end of the DC PEM power switches). Chapter 3 Installing the Cisco 10008 Router
Figure 3-12
Setting PEM Switches to the Off Position
Connecting the Chassis to Ground
POWER FAULT
MISWIRE...
Hardware Installation Guide - Page 60
... ROUTING ENGINE P/N ESR-PRE3
6XCT3-DS0
6XCT3-DS0
POWER FAULT
MISWIRE
PROCESSOR ONLY
OC-12/STM-4 POS SM-IR
30019
Step 1 Set the DC PEM switch (or switches) to the DC power source. Statement 1045
3-18
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
Connecting DC Power to the Cisco 10008 Router
Chapter 3 Installing the Cisco 10008 Router
Recommended Tools and...
Hardware Installation Guide - Page 90
...on, see the Cisco 10000 Series Routers Line Card Hardware Installation Guide. System fails to boot up If the system has power, check the FAIL LED on the PRE and any
properly
information on )
4-12
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
Troubleshooting Installation Problems
Chapter 4 Starting and Configuring the Router
Troubleshooting Installation Problems
This section...
Hardware Installation Guide - Page 103
...0
0
0
SSLLOOTT01
1 1
1
2 2
2
FAIL FAIL FAIL FAIL
8 CISCO 10000
132860
1 Captive screws
Step 4
Slide the new blower module into the chassis, being sure it makes a secure connection to the backplane (Figure 5-12).
Chapter 5 Maintaining the Cisco 10008 Router
Figure 5-11
Removing the Blower Module
1
Removing and Replacing Field-Replaceable Units
FANS OK
FAFILAUNRE FMAFUILALUNTRI...
Hardware Installation Guide - Page 129
...13
Cisco 10008 Router Hardware Installation Guide
5-37 Disconnect any interface cables from the PRE (see Front Cover Procedures, page 5-4). Attach an antistatic wrist strap to your wrist and to the ESD socket on the chassis, or to a bare metal surface on page 5-44). Chapter 5 Maintaining the Cisco 10008 Router
Figure 5-39
ESD Chassis Connection
CISCO 10000
5 5
5 5
5
Connecting Alarm...
Hardware Installation Guide - Page 135
...The system automatically downloads the necessary configuration information from the primary PRE.
Install the PCMCIA card in the chassis by tightening the top and bottom captive screws (Figure 5-45). Step 15 Replace the front cover if necessary (see the "Removing and Installing a PCMCIA Flash Memory Card" section on page 5-44).
Chapter 5 Maintaining the Cisco 10008 Router
Figure...
Hardware Installation Guide - Page 157
... the format also known as M23.
OL-0659-13
Cisco 10008 Router Hardware Installation Guide
GL-7 SONET/SDH specification for a keepalive mechanism, which provides the network server with MAN and WAN. Internet Service Provider.
International Telecommunication Union Telecommunication Standardization Sector.
LMI
includes support for transmit power and receive sensitivity that data is...
Hardware Installation Guide - Page 170
...IN-4
Cisco 10008 Router Hardware Installation Guide
NVRAM file system 4-7 ignoring contents 4-9 size 4-8
O
operating conditions, chassis 2-5 optical network interfaces 1-1
P
Parallel eXpress Forwarding 1-8 password
secret 4-4 Telnet 4-4 PCMCIA backing up 5-3 card slots 1-10 flash cards 1-10, 5-44 PCMCIA flash cards 5-44 PEM AC
description 1-7 installing second 5-24 replacing 5-28 specifications...
Cisco ESR10008 Reviews
We have not received any reviews for Cisco yet.