Cisco 2502 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 2502 Manual Pages
Getting Started Guide - Page 1
GETTING STARTED GUIDE
Cisco 2500 Series Wireless Controller
May 2011 Revised June 2, 2011 1 About This Guide 2 Unpacking and Preparing the Controller for Operation 3 Installing the Controller 4 Running the Bootup Script and Power-On Self Test 5 Logging into the Controller 6 Connecting to the Network 7 What's New in Cisco Product Documentation 8 Translated Safety Warnings
Getting Started Guide - Page 2
...The warnings below are general warnings that are in a particular installation. Statement 1071 SAVE THESE INSTRUCTIONS
2 1 About This Guide
This guide is designed to help . (cfr reference 15.105)
Safety Information
Safety warnings appear throughout this guide are designed to Part 15 of the Cisco 2500 Series Wireless Controllers. This equipment generates, uses, and can be determined by one...
Getting Started Guide - Page 3
...The 2504 controller comes with Cisco lightweight access points and the Cisco Wireless Control System (WCS...instructions. Warning
There is the danger of a suitably installed ground conductor. Replace the battery only with a minimum of used batteries according to the Controller
The 2504 controller works in increments of services for mobility services such as voice and video, and OEAP support...
Getting Started Guide - Page 4
... crossover cables.
The controller has an auto MDI feature, so you can use this guide, you should have already designed the wireless topology of your network and have a working knowledge of access points to main office
10/100/1000BASE-T MDI cables
Access point connections
282297
Cisco Access Points
4
Figure 1 shows a 2504 controller network topology and...
Getting Started Guide - Page 5
... recovery mechanism is an RS-232 port that supports a RJ-45 connector. Figure 2 Front Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model ...supports baud rates of 9600, N, 8, 1. however the bootloader ensures that there will default to unit. Note
It is expected that the stored baud rate setting matches one of the LED manufacturer's specifications...
Getting Started Guide - Page 6
...port is designed so that 1500 VAC rms
isolation (per the 802.3 specification) is met between the PSE controller and host CPU TWSI bus #1.
LED description:
• Green or ...isolation (per the 802.3 specification) is met between
chassis ground and any 48V/Ethernet signal. The POE controller is an RJ-45 connector
form-factor. This interface supports the proper voltage isolation ...
Getting Started Guide - Page 10
... downloading operating system software updates).
No is less convenient, but has lower security (session can contain up to clients and the management interface. • A virtual gateway IP address (a fictitious, unassigned IP address, such as 1.1.1.1, used by all Cisco
wireless controller Layer 3 security and mobility managers). • A Cisco wireless controller mobility or RF group...
Getting Started Guide - Page 18
Step 6 For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On ...the controller as shown in Figure 9 with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Mounting the Controller in a Rack
To mount the 2504 controller in a rack, follow these steps. Statement 1006
To install the controller in...
Getting Started Guide - Page 24
Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU - Run primary image (7.0.114.76) - Change active boot image 4. Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to access the Boot Menu... The bootup script displays operating system software initialization (code download and POST verification) and...
Getting Started Guide - Page 25
...Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok
25 Flags-[DUTY CYCLE] : ok Fastpath CPU00: Initializing last packet received queue. All rights reserved. Cisco AireOS Version 7.0.114.76 Firmware...
Getting Started Guide - Page 27
...not reboot the controller until the user login prompt appears. Change active boot image 4. Loading primary image (7.0.114.76) 100% 31427987 bytes read Launching images... Cisco AireOS Version 7.0.114.76 Firmware Version PIC 14.0 Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Initializing Licensing Services: ok Starting ARP Services: ok Starting Trap...
Getting Started Guide - Page 30
... username is the name you want to assign to enterprise services such as AAA servers.
Table 3
Startup Wizard Information
Wizard Setting System Name Administrative user name
Administrative password
Action
Enter the system name, which is admin. Enter the IP address of the default router. The VLAN identifier should be assigned to match the switch...
Getting Started Guide - Page 31
... is the default SSID that you want the controller to configure DHCP Bridging Mode. All controllers within a mobility group must be configured with the same virtual interface IP address.
The following message appears:
Warning! Network Name (SSID)
Enter the network name, or service set identifier (SSID). You should enter a fictitious, unassigned IP address, such...
Getting Started Guide - Page 35
... access point MAC address in Figure 14. When you are not currently
supported. The controller Radio Resource Management (RRM) feature automatically configures the access point to start transmitting and allowing clients to meet the specific needs of access points to Cisco 2500 Series Wireless Controllers are connecting to a hub or a switch, use Category-5, Category-5e, Category-6, or...
Getting Started Guide - Page 37
..., it reboots and loads the configuration. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
37
If you have not configured the controller, the configuration wizard appears.
7 What's New in Cisco Product Documentation
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in...
Cisco 2502 Reviews
We have not received any reviews for Cisco yet.