Instruction Manual - English
Page 7
... 31 5-1. Direct selection 48 6-9. Loading additional sewing data 48 7. Cleaning the rotary hook 50 8-2. TABLE OF ERROR CODES 55 KE-430D, BE-438D Program list (BE-438D 8 3. Installing the control box 12 3-3. PREPARATION BEFORE SEWING.....23 4-1. Winding the lower thread 25 4-4. Upper thread... thread counter 40 6-5. Draining the oil 51 8-4. Applying grease (Work clamp: KE-430D 52 8-8. Program list (KE-430D 3 2-3. Installing the button tray (BE-438D 15 3-9. Connecting the ground wire 18 3-12. Connecting the power cord 21 3-15. Threading the upper ...
... 31 5-1. Direct selection 48 6-9. Loading additional sewing data 48 7. Cleaning the rotary hook 50 8-2. TABLE OF ERROR CODES 55 KE-430D, BE-438D Program list (BE-438D 8 3. Installing the control box 12 3-3. PREPARATION BEFORE SEWING.....23 4-1. Winding the lower thread 25 4-4. Upper thread... thread counter 40 6-5. Draining the oil 51 8-4. Applying grease (Work clamp: KE-430D 52 8-8. Program list (KE-430D 3 2-3. Installing the button tray (BE-438D 15 3-9. Connecting the ground wire 18 3-12. Connecting the power cord 21 3-15. Threading the upper ...
Instruction Manual - English
Page 35
...OFF". [Notes on use scissors to cut the thread without pulling it up too hard. 4475Q KE-430D, BE-438D 28 However, some limitations apply. Furthermore, if using the thread nipper device, turn the tension nut (1) (sub...first stitch, the end of these cases, use ] 1. When using thick thread that is too long, an error [E691] may become wound around the seam. Refer to "ON". In any of the thread that is #30... a good seam at times when skipped stitches might easily occur. List of memory switches" for details. * The default setting for this memory switch is set to "6-3.
...OFF". [Notes on use scissors to cut the thread without pulling it up too hard. 4475Q KE-430D, BE-438D 28 However, some limitations apply. Furthermore, if using the thread nipper device, turn the tension nut (1) (sub...first stitch, the end of these cases, use ] 1. When using thick thread that is too long, an error [E691] may become wound around the seam. Refer to "ON". In any of the thread that is #30... a good seam at times when skipped stitches might easily occur. List of memory switches" for details. * The default setting for this memory switch is set to "6-3.
Instruction Manual - English
Page 36
If error [E690] or [E691] frequently occurs, remove the needle plate and remove any thread scraps from the seam on the .... With the KE-430D, the lower thread may poke out from underneath the needle plate. (Back) Upper thread 4487Q 5. Program list (KE-430D)" for thread nipper device 65 66 67 68 69 70 71 72 78 79 80 81 82 83 84 85 73... 74 75 76 77 29 KE-430D, BE-438D for details of the material. Specifications For ordinary materials (-01) For denim (-02) For knitted materials (-07) For foundation garments (-0F) Standard ...
If error [E690] or [E691] frequently occurs, remove the needle plate and remove any thread scraps from the seam on the .... With the KE-430D, the lower thread may poke out from underneath the needle plate. (Back) Upper thread 4487Q 5. Program list (KE-430D)" for thread nipper device 65 66 67 68 69 70 71 72 78 79 80 81 82 83 84 85 73... 74 75 76 77 29 KE-430D, BE-438D for details of the material. Specifications For ordinary materials (-01) For denim (-02) For knitted materials (-07) For foundation garments (-0F) Standard ...
Instruction Manual - English
Page 64
... Turn off the power, and then check if there are any problems in power supply voltage. Internal memory is full and copying is properly connected. Input an end code, or change the program ...with scraps of purchase. 57 KE-430D, BE-438D Data cannot be backed up to extend outside the sewing area. Data editing-related errors Code E500 E501 E502 E510 Cause and remedy The...current detected in work clamp lifter. board. Check if the upper thread trailing length is not listed above appears or if carrying out the specified remedy does not solve the problem, contact the place...
... Turn off the power, and then check if there are any problems in power supply voltage. Internal memory is full and copying is properly connected. Input an end code, or change the program ...with scraps of purchase. 57 KE-430D, BE-438D Data cannot be backed up to extend outside the sewing area. Data editing-related errors Code E500 E501 E502 E510 Cause and remedy The...current detected in work clamp lifter. board. Check if the upper thread trailing length is not listed above appears or if carrying out the specified remedy does not solve the problem, contact the place...
