Troy-Bilt TB675 Support Question
Troy-Bilt TB675 Support Question
Find answers below for this question about Troy-Bilt TB675.Need a Troy-Bilt TB675 manual? We have 1 online manual for this item!
Question posted by mnellammij on August 20th, 2013
Wont Stay Running
my father in law uses my weed eater and it runs fine but as soon as i try to use it it stalls when i try to start working
Current Answers
Related Troy-Bilt TB675 Manual Pages
Operation Manual - Page 1
...without notice. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE. When servicing, use only identical replacement parts.
769-08458 / 02
All information, illustrations, and ... Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB675 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation...
Operation Manual - Page 2
...start or run the unit inside a closed room or building. keep these requirements could subject you to liability or a fine... and Washington require, by law that are no sparks or...using the unit, all fasteners are approached, stop the engine and allow it to cool before starting the unit. CALIFORNIA PROPOSITION 65
WARNING: Engine exhaust, some of its vapors
can result in effective working...
Operation Manual - Page 3
... the unit: 1. Do not run the unit at high speed when...working on both handles or grips.
• Do not overreach. Do not operate the unit with anything before repairing damage. Refer to stop the unit immediately. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Do not touch or try to them often and use...
• Avoid accidental starting . Disconnect the spark ...
Operation Manual - Page 4
...SHARP BLADE
WARNING: Sharp blade on this product. SYMBOL MEANING
• ON/OFF STOP CONTROL ON / START / RUN
• ON/OFF STOP CONTROL OFF or STOP
• PRIMER BULB Push primer bulb, fully and ...MEANING
• SAFETY ALERT SYMBOL Indicates danger, warning or caution. Use a full face shield when needed.
• UNLEADED FUEL Always use clean, fresh unleaded fuel.
• OIL Refer to the ...
Operation Manual - Page 5
...the right to make changes at the time of printing. Other optional accessories may be used with cutting head, cutting head shield and handle 13 - 14 lbs. (5.9 - ... at any time without notice.
5 KNOW YOUR UNIT
APPLICATIONS
As a trimmer: • Cutting grass and light weeds. • Edging • Decorative trimming around trees, fences, etc. Shaft Grip
Muffler
Spark Plug
Starter Rope Grip...
Operation Manual - Page 6
... do not tighten the bolt completely.
3. Tighten the bolt with a 3/8" socket until finger tight.
3. Using a #2 Phillips screwdriver, tighten the screws until the handle is firmly in the handle should be to the... the holes in the mount bracket. (Fig. 1)
2. Screws (2)
Use the following instructions if the cutting head shield is secure. Tighten the bolt with a 3/8" socket until ...
Operation Manual - Page 7
...1. Turn the knob counterclockwise to loosen (Fig. 3). 2. Press and hold the release button (Fig. 4). 3. WARNING: Before using any attachment, read and
understand the manual that came with the guide recess will help installation (Fig. 4). 3. NOTE: To ...or removing the attachment easier, place the unit on the ground or on a work bench.
Follow all safety information contained within.
Operation Manual - Page 8
... fill plug (Fig. 7). 5. Wipe up any oil that may have spilled. 7. Remove the cap from the oil bottle. Failure to use clean oil of oil. 1. Check the oil level before starting the unit.
Unscrew the top of oil during future oil changes. Set the unit on the oil fill plug (Fig. 7). DO...
Operation Manual - Page 9
.... 5. Keep sparks and open flames at least 30 ft. (9.1 m) from fuel spray. Do not start the engine until fuel vapors dissipate.
1. Add 0.8 oz. (23 ml) of fuel additive per gallon... Using Blended Fuels If using a blended fuel: • Always use fresh unleaded gasoline • Use the fuel additive STA-BIL® or an equivalent • Drain the tank and run the engine dry before starting the...
Operation Manual - Page 10
... throttle control for 2-5 minutes, or as needed . The unit may be used during this time. If it does not, repeat this unit only in the starting the unit. Run the unit for 2-5 minutes, or as needed .
the engine does not start, begin the starting procedure with a controlled and steady motion 3 to 5 times to Position 3 and...
Operation Manual - Page 11
... Position 3 (Fig. 10) and continue warming the engine for more information.
Move the choke lever to turn the unit on. Run the electric start accessory (items sold separately).
The unit may be used during this time.
Fill the fuel tank. Slowly press and release the primer bulb 10 times (Fig. 9).
4.
Squeeze and hold...
Operation Manual - Page 12
... the operator. • Do not trim wet grass or weeds. This may lead to serious personal injury or damage to the...injury when operating this unit.
• Stand in tall grass may stall the engine. Trimming line can be released from left to release line ...unit at high speed. ADJUSTING THE TRIMMING LINE LENGTH This unit is
running. For best results, tap the bump knob on the ground (Fig...
Operation Manual - Page 13
... re-oil the air filter.
NOTE: Always use metal-reinforced line, wire, chain or
rope... in the Specifications section.
WARNING: Never use the correct line length when installing trimming ...any old trimming line and/or obstructions from starting accidentally. MAINTENANCE
WARNING: To prevent serious ...too long.
REPLACING THE TRIMMING LINE
Only use the trimming line described in the table....
Operation Manual - Page 14
...If the oil level is in the tabs on the oil fill plug (Fig. 20). Look into the holes. use . Refer to overfill. 3. Add oil to clean the inner reel, outer spool and spool
cover (Fig. 18... outer spool until the oil level is level (Fig. 19). NOTE: DO NOT overfill the crankcase. 4. Use a clean cloth to the oil fill hole until the tabs securely snap into the oil level window; Align ...
Operation Manual - Page 15
...air filter can result in poor performance or can cause permanent damage to prevent debris
from the initial use to cool before cleaning or maintaining the unit.
Remove the air filter cover from the air filter housing... air filter with clean SAE 30 oil. 5. Swing the air filter cover to dry. 4. NOTE: Use the empty oil bottle saved from entering the oil fill hole. 2. oz (60 ml) fill line ...
Operation Manual - Page 16
...of the following conditions are true, take the unit to prevent serious personal injury. NOTE: If using a torque wrench, torque to set the air gap at a time (as follows: 1. WARNING...8226; the engine hesitates or stalls on acceleration • there is cracked, fouled or dirty, replace it clockwise until the engine idles smoothly (Fig. 24). 3. Start the engine. Use a feeler gauge to : ...
Operation Manual - Page 17
...Start the engine and allow it to cool before storing. • Lock up the unit to prevent unauthorized use or damage. • Store the unit in a horizontal position. Pull the starter rope slowly to Changing the Oil.
Dispose of children. Do not use...to run until it stalls. Long-term Storage
1. Allow the engine to clean the outside of any moisture with the engine at the top.
Use a ...
Operation Manual - Page 18
...the fuel tank and add fresh fuel Replace the spark plug Refer to the IF... PROBLEM THE ENGINE WILL NOT START The fuel tank is empty The primer bulb was not pressed enough The fuel is old (over 30 days)...
SOLUTION
Fill the fuel tank with grass The air filter is dirty
THE ENGINE LACKS POWER OR STALLS The fuel is old (over 30 days) The spark plug is fouled
The engine is required, contact an authorized...
Operation Manual - Page 20
... without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or...period of Troy-Bilt. Tune-ups - How State Law Relates to this Warranty provide the sole and exclusive remedy...Manual furnished with the product, and has not been subject to use the product. C. Bump Knobs, Outer Spools, Cutting Line, Inner...
Similar Questions
Troy-bilt Tb675 Overheating
My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?
My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?
(Posted by Anonymous-154291 8 years ago)
Why Does My Troy Built Trimmer Tb675 Ec Overheat ?
(Posted by Anonymous-154291 8 years ago)
Very Hard To Start And Won't Stay Running
my friend gave me a tb4hb because it was so hard to start. After 15 min of pulling the rope, it fina...
my friend gave me a tb4hb because it was so hard to start. After 15 min of pulling the rope, it fina...
(Posted by luthersprouse 9 years ago)
Proline Crt Want Stay Running
It cranks right up, although its harder to pull than it use to be but as soon as it meets any resist...
It cranks right up, although its harder to pull than it use to be but as soon as it meets any resist...
(Posted by janmills64 9 years ago)
Oil For Troy-bilt Tb675
what kind of oil should I put in my Troy-Bilt TB675
what kind of oil should I put in my Troy-Bilt TB675
(Posted by herjeac 10 years ago)