Thermador T30IF800SP Support Question
Thermador T30IF800SP Support Question
Find answers below for this question about Thermador T30IF800SP.Need a Thermador T30IF800SP manual? We have 1 online manual for this item!
Question posted by weldesigns on September 2nd, 2018
Parts Diagram For Thermador T30if800sp And An Ice Maker That Will Not Stop
1) Where can I find a detailed parts diagram? A small plastic clip that holds the top right corner of the top-hinged panel covering the ice maker has broken and I need to replace it -- preferably without a $200 service call.2)The ice maker is internal (does not dispense through door) and never stops making cubes . . . they overflow and fill the shelves below. I cannot find anything about it in frequently asked questions anywhere I have looked so far. I wonder of a part was not installed, or a setting is wrong??
Current Answers
Related Thermador T30IF800SP Manual Pages
Installation Manual - Page 4
...31 Aligning the ice-water dispenser 31 Attaching the cover strips 32 Adjusting the door opening angle 33
4 Loading the appliance door 19 6. Attaching the door panel 21 10. ...water to the installation enclosure 16
1. Removing the installation
support part 19 7. Attaching the fixation strips
to the door panel 20 8. Removing the packaging 11 3. Attaching the anti-tip-...
Installation Manual - Page 5
...covered under the Appliance Warranty. Due to the weight and size of this appliance, and to reduce the risk of not observing this warning.
Immediately repair or replace electric service...carpentry and plumbing skills. IMPORTANT
Save these instructions for local inspector's use by a qualified service technician. Be sure to Installer - In the absence of this appliance only for warranty ...
Installation Manual - Page 6
...for Side-by-Side Installation if the gap between the appliances is visible, a side panel must be used.
Individual appliance at the same time.
Use the Heater Kit for model 4, note ... the doors are opened at the end of the kitchen
If one side of the side panel are many different installation options. See also "Kitchen Design Quick Reference". During installation ensure that...
Installation Manual - Page 7
....
7 Installation enclosure
Note:
It is strongly recommended the top panel of the niche be attached securely to the upper and side ...Freezer 30"
approx. 950 Ibs/425 kg*
Wine unit 18" approx. 550 Ibs/245 kg
Wine unit 24" approx. 694 Ibs/310 kg
(* without Water Dispenser)
Installation room
The appliance should be flat and level.
On account of the heavy weight of the ice maker, ice...
Installation Manual - Page 8
...be installed by a qualified electrician or service technician if you are available as to...:
Only connect the appliance to plastic plumbing lines, gas lines or ...Freezer 30" (incl. The water pressure must not be located at the side on the right (a), at one time 2.0 Ampere 2.0 Ampere 3.5 Ampere
4.0 Ampere
4.5 Ampere
2.0 Ampere 2.0 Ampere
For the installation position of the automatic ice maker...
Installation Manual - Page 9
... the enclosure must be accessed for installation of the water connection
It is strongly recommended the top panel of the enclosure be at least 5/8" (16 mm) thickness.
Installation dimensions
X
18" (457...depending on kitchen design C = 24" (610 mm) minimum
9 Legend: A Area for service without uninstalling the appliance. IMPORTANT ! It is recommended the water-box be placed adjacent to...
Installation Manual - Page 10
... work .
Other required accessories
Ice maker installation kit 1/4" OD copper line For connecting appliances which require water, e.g. Freezer next to protect the floor from damage Suitable material for Side-by -Side Installation BSEALKIT10
For permanent connection of the water pipe (without further preliminary work surfaces! Freedom Heater Kit for covering and protecting furniture...
Installation Manual - Page 11
...; Refrigerator units
Freezer units
Freezer units with ice maker
Freezer units with ice maker). Check that adjacent cabinet/... inside the appliance until the installation is complete, otherwise the parts may be damaged!
The appliance may tip over ...ice-water dispenser
Wine storage units
Therefore the diagrams may be damaged.
11 If in transit.
Installation Manual - Page 12
...via the side panels. Special installation
This symbol indicates that additional steps need to prevent it...described after section C.
Change over door hinge, see "Changing over the door hinges".
Sealing mat, see "Removing/ ...
Ice-water dispenser, see "Aligning the ice-water dispenser".
Cover strips for a wine unit, see "Attaching the cover strips"
...
Installation Manual - Page 13
... glasses and other necessary protective devices or apparel when installing or working with dowels and screws:
Not recommended for fastening with dowels. Be sure screws hold tight. 1.
The anti-tip-brackets (a) must overlap a minimum of injury!
Attaching the anti-tip-brackets
, WARNING:
Risk of the installation enclosure!
1. Select the fastening screws...
Installation Manual - Page 17
... special installation steps. These parts have been removed. Shorten the fitting strip (a) to the required height to the attachment plate (top).
4.
Press fitting strip (a) into the cover strip.
7. Screw on ...5. 3. Note: In the case of the fastening sheets (lateral) with the cabinet parts located next to the bolt included in the installation accessories for side-by-side installation....
Installation Manual - Page 19
... to shut off valve closed.
4. Removing the installation support part
Unscrew the positioning aid from customer service as possible. Switching the appliance ON
To guarantee the accuracy of...separate installation instructions for appliances with weights in an installation step later.
19 These door panels must not exceed the following :
Always screw into the best load-bearing...
Installation Manual - Page 23
... appliance is included in the installation accessories for a wine unit, see "Attaching the cover strips"
Door limitation pin, see "Aligning the ice-water dispenser".
Cover strips for side-by -Side installation only:
These are provided after section C.
Ice-water dispenser, see "Adjusting the door opening angle".
Instructions are special installation steps...
Installation Manual - Page 24
... door.
4. Remove the hinge box covers.
5.
Loosen the screw from I to 0.
2. Remove the hinges.
1. Release the spring on the hinge, release the spring. Remove the ventilation grille.
24 Note: The door hinges cannot be exchanged in the case
of injury! Special installation
Changing over the door hinges
, WARNING:
Risk of freezers with ice and water dispensers. ...
Installation Manual - Page 25
Change over the screw for the ventilation grille to adapt to the modified door hinge is included in the installation materials and accessories.
9. Attach the ventilation grille. Mount new the ventilation grill.
7. A replacement part for the lower bracket.
25 6. Change over the hinge angle.
8.
Installation Manual - Page 26
Fix the door.
26 Change the hinges crosswise!
14. Span the spring on the door.
13. 10. Change over the fixation parts on the hinge. Tighten the screw from 0 to I.
11. Fix the hinge box cover.
12. Fix the hinges on the appliance.
Installation Manual - Page 27
... sealing mat must also be removed.
Removing/changing over the sealing mat
Freezers are missing.
For the Side-by -side installation. If the door hinge of the freezer to the opposite side.
2. Unpack the Side-by-Side kit and check that no parts are factory equipped with a sealing mat for the Side-by -Side...
Installation Manual - Page 28
...; Attach the mat always left standing appliance! 4. Continues the work to both appliances! Unscrew the base panels.
5.
3. Place the water-absorbing stripes from the Side-by -side installation. Stick sealing mat from ... for
the Side-by -Side kit around the edge. Note: Freezers are factory equipped with self adhesive tape.
6. Note the position of both appliances. Secure the sealing ...
Installation Manual - Page 30
... appliances which require a water connection)
Note:
Turn off valve according to the bolt included in the appliance.
16.
Connect both cover rails to the instructions supplied by the manufacturer of the ice maker installation kit.
2. When the appliances have been completely pulled together, insert the bar into the lower plates.
Pull the appliances...
Installation Manual - Page 31
...on the appliance for freezer unit with ice-water dispenser only)
...cover frame onto the ice-water dispenser and press in order to attach the frame before adjusting the dispenser unit!
1. Using the open-ended wrench, tighten the union nut. Insert flat screwdriver into one of the door panel.
Loosen screws on the union nut (3.). Remove the cap from the door panel (2.).
4.
The ice...
Similar Questions
My Thermador T18id800lp: Ice Maker Will Not Make Ice Or Dispense Water.
After emptying the ice container and replacing it into the freezer, it will not make ice. In additio...
After emptying the ice container and replacing it into the freezer, it will not make ice. In additio...
(Posted by morningglorysally 3 years ago)
Ice Maker On The Blink
My refrigerator was reinstalled after a kitchen renovation and the ice maker stopped working. The pl...
My refrigerator was reinstalled after a kitchen renovation and the ice maker stopped working. The pl...
(Posted by Caidouwes 3 years ago)
Ice Maker Is Not Operating
The filter and water is OK. The motor don't operate for put the ice cube and the boket.
The filter and water is OK. The motor don't operate for put the ice cube and the boket.
(Posted by legaremarcel 7 years ago)
Positioning Aid
we are trying to install the integrated panel for our freedom columns. The manual says to use the po...
we are trying to install the integrated panel for our freedom columns. The manual says to use the po...
(Posted by Anonymous-159115 7 years ago)
Thermador T18id80nlp/17 Freezer Not Dispensing Ice
The ice maker makes ice but it does not dispense the cubes.
The ice maker makes ice but it does not dispense the cubes.
(Posted by akouroupos 7 years ago)