Singer 3323 Talent Support Question
Singer 3323 Talent Support Question
Find answers below for this question about Singer 3323 Talent.Need a Singer 3323 Talent manual? We have 2 online manuals for this item!
Question posted by bobandlaurie52 on August 19th, 2014
Cloth Advances Backwards Only
Machine sewing fine. Stopped, and started sewing againand only advances material backwards. Moving backward lever changes nothing. Thank you/BoB
Current Answers
Related Singer 3323 Talent Manual Pages
Instruction Manual - Page 2
...needle, changing needle, threading bobbin, or changing presser foot, and the like. 10. Never operate this manual. 3. Special care is 75dB(A). 17. Always use outdoors. 13. Switch the sewing machine off ...is damaged, it to the off the machine or unplug when the machine is being administered. 14. Keep ventilation openings of lint, dust, and loose cloth. 5. The wrong plate can cause ...
Instruction Manual - Page 6
EN List of contents
Machine Basics Principle Parts of the Machine...2/4 Connecting Machine to Power Source ...6 Two Step Presser Foot Lifter ...8 Accessories ...9
Threading the Machine Winding the Bobbin...11 Inserting the Bobbin ...13 Threading the Upper Thread ...15 Automatic Needle Threader ...17 Raising the Bobbin Thread ...19 Thread Tension...21
Sewing How to Choose Your Pattern...
Instruction Manual - Page 9
Bobbin stopper
4
11
9. EN Principal Parts of the Machine
1. Needle plate cover
2
10
7. Automatic threader
13. Reverse sewing lever
1
8
4. One step buttonhole lever
7
12 13
2 Presser foot
6. Removable extension table/ accessory storage
3
8. Thread take-up lever
3. Stitch length dial
5
11. Pattern selector dial
6
12. Thread tension dial
2. Stitch width ...
Instruction Manual - Page 13
... in use . EN Connecting Machine to Power Source
Connect the machine to a power source as ...illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2)
Attention: Unplug power cord when machine is not in a polarized outlet only one blade is wider than
a
the other). Co., Ltd. (Vietnam)
Sewing...
Instruction Manual - Page 16
Button sewing foot e. Spool holders m. L-screwdriver o. they are not supplied with this machine; Twin needle
9
2
s
006172008
w
006904008
t
u
006907008
x
006900008
y
006916008
v
006813008 Pack of needles l. Bobbin (3x) n. All purpose foot b. Darning/ embroidery foot g. Darning plate p. Blind hem foot x. Seam ...
Instruction Manual - Page 18
...(3)
- Wind thread clockwise around bobbin winder tension discs. (4)
- Place thread and corresponding spool holder on to left (sewing position).
4
3
5
6
7
8
9
10
11 EN Winding the Bobbin
- Cut thread. (9) 2
- Push...:
When the bobbin winder spindle is in "bobbin winding"
position, the machine will not sew and the hand wheel will
not turn. Step on spindle. (5)
- Push bobbin spindle ...
Instruction Manual - Page 30
EN How to sew these stretch patterns is a stretch stitch pattern, and information on how to Choose Your Pattern
The diagram on this page display the stitch patterns available on the machine. The blue indicates that the stitch is on page...stitch as desired for the project. Reverse Sewing Lever b. Stitches in the top of the diagram are indicated on the Pattern Selector Dial in either direction...
Instruction Manual - Page 34
EN Sewing Straight Stitch
To begin sewing, set the machine for straight stitch. (1) Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2) Lower the presser foot lifter, and then step on the foot controller to start sewing. (3)
1
2
3
27
Instruction Manual - Page 36
... stitches. Release the lever and the
A
machine will sew forward again. (1)
Removing the Work
Turn the handwheel toward you (counterclockwise) to bring
the thread take up lever to cut. (3)
3
29
2 B Pull threads down the reverse sewing lever (A). EN Reverse Sewing
To secure the beginning and the end of the face plate and into thread cutter (B). Guide the...
Instruction Manual - Page 38
... (2)
1
Set the Pattern Selector Dial to " ".
Used to add triple reinforcement to between "3" and "6". Adjust the Stitch Width Dial to stretch and hardwearing seams.
The machine sews two stitches forward and one stitch backwards. Ric Rac Stitch is suitable for firm fabrics like denim, corduroy, poplin, duck, etc.
2 31
Instruction Manual - Page 40
... weight fabrics, and a wider stitch is completed and press. 2
Note:
To make sure the machine settings are normally sewn with the range shown on curtains, trousers, skirts, etc. EN Blind Hem...top edge of the hem extending about 7 mm (1/4") to the
1
right side of the page.
Start to sew slowly on the right of the folded fabric. Blind hems, however, are appropriate for the fabric....
Instruction Manual - Page 42
...will overcast the cord.
1. Lower the presser foot and start the machine. 7.
Using tailor's chalk, mark the position of the buttonhole on the
fabric. 2. Sew a test first to " ". The width however may....
3. Lower the buttonhole lever and gently push it is sewn the
legs will be adjusted according to the project.
EN Sew 1-Step Buttonhole
Buttonhole sewing is done in the order...
Instruction Manual - Page 44
... shank is required, place a darning needle on Buttons
Install the darning plate. (1) Change the all purpose foot to the button sewing foot. (2) Set the stitch length to the distance between the holes of the button...about 10 stitches. Raise the needle out of the fabric. Set the machine for straight stitch again, then sew a few securing stitches to check that the needle goes cleanly into the...
Instruction Manual - Page 48
... darning/ embroidery foot on firmly from left to hold layers of fabric.
The lever (a) should be behind with your index finger and tighten the screw (c). (3) For darning, first sew around the edge of the fabric is accomplished without the sewing machine internal feed system. A darning hoop is necessary to the presser foot bar. Turn...
Instruction Manual - Page 67
... insert correctly. 3. Remove the upper thread and bobbin case, turn the handwheel backwards and forwards by the machine.
1. Skipped stitches
Needle breaks
Loose stitches
Seams gather or pucker Uneven stitches, ...noisy
The machine jams
1. Remove the reel and wind thread onto reel. 6. Replace the needle.
1. Remove and reinsert the bobbin case and pull on the fabric while sewing, let it...
Instruction Manual 2 - Page 2
.... 14. Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any air openings blocked. Please turn all moving parts. If the supply...dust, and loose cloth. 5.
DANGER - Replace bulb with any adjustments in this appliance only for household use as threading needle, changing needle, threading bobbin, or changing presser foot, ...
Instruction Manual 2 - Page 36
... end of a seam, press down to the side of the face plate and into thread cutter (B). Sew a few reverse stitches. Guide the threads to cut. (3)
3
29
2 B Pull threads down the reverse sewing lever (A). Release the lever and the
A
machine will sew forward again. (1)
Removing the Work
Turn the handwheel toward you (counterclockwise) to bring
the thread...
Instruction Manual 2 - Page 38
... Choosing Stretch Stitch Patterns
The Stretch Stitch Patterns are two examples:
Straight Stretch Stitch (1)
Set the Pattern Selector Dial to stretch and hardwearing seams.
The machine sews two stitches forward and one stitch backwards. Then, turn the Pattern Selector Dial to the indicator marked "S1".
Instruction Manual 2 - Page 44
...of the fabric. Set the machine for zig-zag stitch, then set the width to finish.
"6".
Set the machine for straight stitch again, then sew a few securing stitches to...sew through the
front two holes first, push the work forward and then sew
through the back two holes.
3
4
37 EN Sewing on Buttons
Install the darning plate. (1) Change the all purpose foot to the button sewing...
Instruction Manual 2 - Page 67
...the bobbin case and pull on the fabric while sewing, let it be lubricated. 2. Correct the thread tension.
1. Loosen the thread tension.
1. The machine is wrong. 4. The thread is too thick... pull on the thread. Remove the upper thread and bobbin case, turn the handwheel backwards and forwards by the machine.
1. The bobbin case is wound around the spool holder pin. 6. Remove and ...
Similar Questions
Singer Talent 3323 Timing Is Off. How Do You Remove The Black Bobbin Holder To
Singer Talent 3323 timing is off. How do you remove the black bobbin holder to access underneath
Singer Talent 3323 timing is off. How do you remove the black bobbin holder to access underneath
(Posted by fmodin 2 years ago)
Machine Was Working Fine Suddenly Started Going In Reverse,i Cleaned It Oiled
it did manage to get it going but it happened again
it did manage to get it going but it happened again
(Posted by irenemusket 6 years ago)
Sewing Wheel Will Not Turn
I have a singer talent 3323 and the wheel that controls the needle will not move. It also looks as i...
I have a singer talent 3323 and the wheel that controls the needle will not move. It also looks as i...
(Posted by gabriellemharris 9 years ago)
Machine Will Not Pick Up Bobbin Thread & Stiff Hard To Move To Pick The Thread.
(Posted by Mparchapr 10 years ago)
Machine Does Not Stop Stitching Until Power Is Shut Off
When my machine is in default mode (straight stitching), it continues to stitch even after I have li...
When my machine is in default mode (straight stitching), it continues to stitch even after I have li...
(Posted by brosenberg129 10 years ago)