Ryobi TS1141L Support Question
Find answers below for this question about Ryobi TS1141L.Need a Ryobi TS1141L manual? We have 2 online manuals for this item!
Question posted by wpfas on September 25th, 2011
Ryobi Dust Bag
where can i find a dust bag for a ryobi model TS1141L
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Ryobi TS1141L Manual Pages
Operation Manual - Page 2
... TWO YEAR WARRANTY AND 30 DAY EXCHANGE POLICY One World Technologies, Inc., warrants its RYOBI® power tools with the original product. WHAT THIS WARRANTY COVERS: This warranty covers all original equipment ...year period from which does not work in a reasonable time, but, in your RYOBI® power tool for making it was purchased. With the exception of this product making its use ...
Operation Manual - Page 3
... dusty. PROTECT YOUR HEARING. A guard or other conditions that it was designed. USE THE RIGHT TOOL. Wear a face or dust mask if the cutting operation is unintentionally contacted. CHECK DAMAGED PARTS. When tool is safer than using your hand and frees both hands to avoid risk of parts, mounting and...
Operation Manual - Page 4
...products and some plastics only. SPECIFIC SAFETY RULES
FIRMLY CLAMP OR BOLT the tool to install the proper outlet. Normal sparking of any operation freehand. If it firmly against... securely tightening the miter lock lever. Lock the saw from lumber before connecting to clean tool. STAY ALERT AND EXERCISE CONTROL. Do not use brake fluids, gasoline, petroleum...
Operation Manual - Page 5
... lighting to see the work surface before changing blade or servicing.
ALWAYS carry the tool only by an authorized service center to avoid risk. Always stay alert! Do not...the saw blade to stop . NEVER leave the saw unattended while connected to a power source THIS TOOL should any work using the laser guide. SAVE THESE INSTRUCTIONS. d) Do not perform any ...
Operation Manual - Page 6
... avoided, may result in damp locations. SYMBOL
NAME
Safety Alert Read Operator's Manual
DESIGNATION/EXPLANATION
Precautions that may be used on this tool. Do not expose to operate the tool better and safer. SYMBOLS
The following symbols may result in serious personal injury. DANGER: WARNING: CAUTION: CAUTION:
Some of these symbols will...
Operation Manual - Page 9
x 3 in . Miter Lock lever "D" handle switch lock Upper Blade Guard Dust BAG
BLADE WRENCH
laser guide Switch Trigger
Lower blade guard
Bevel Lock Knob
Bevel Scale
"NO HANDS ZONE" BOUNDARY LINE "NO HANDS ZONE" LABEL bevel scale
...
Operation Manual - Page 12
... Base Blade Wrench Miter Saw Head AAA Batteries (2) Dust Bag Rear Bracket/Carrying Handle Work Clamp Bevel Knob Blade ...; Bevel Indicator and Screw Operator's Manual
miter saw base
DUST BAG
WORK CLAMP
AAA Batteries
blade wrench miter saw head
bevel knob rear bracket/ carrying handle...
Operation Manual - Page 15
... the head at both 0º and 45º to make sure the indicator is already factory assembled, proceed to the next section to install the Dust Bag. Set the bolt, spring washer, and flat washer aside. Place the miter saw head on the saw head. The bolt should be set to...
Operation Manual - Page 16
... clamp to secure the workpiece prior to the fence or the table. To remove the dust bag for use a C-clamp instead of serious personal injury.
To install, squeeze the two...cover. Base
Work Clamp Fig. 13 compartment cover batteries screw
Fig. 14 16 ASSEMBLY
DUST BAG
See Figure 12. A dust bag is very helpful when cutting compound miters. Release the clips. Remove cover and set ...
Operation Manual - Page 27
... features of the miter saw does an excellent job of cutting crown molding than any other angle as well. changing one angle changes the other tool made. Since it is placed flat on miter table. When cutting crown molding by this method for accurately cutting crown molding for these angles to...
Operation Manual - Page 29
... adjustment screw. Retighten bevel lock knob. Make any adjustment, make sure that are necessary and periodically check the parts alignment to make sure the tool is unplugged from the power supply.
BEVEL LOCK KNOB
TRAVEL PIVOT ADJUSTMENT
The saw arm should bevel easily by loosening the bevel lock knob...
Operation Manual - Page 31
... curvature of high grade lubricant for wear. Therefore, no further lubrication is dusty, also wear a dust mask. Brush Cap Brush Assembly
WARNING:
Always wear eye protection with a screwdriver. Proceed as follows... saw . Brush Assembly Brush Cap
GENERAL MAINTENANCE
Avoid using new brush assemblies. Electric tools used on these materials, it is spring loaded and will pop out when you do not...
Operation Manual - Page 32
... Authorized Service Center. Be sure to provide all pertinent facts when you do this tool will be found on a plate attached to cause cancer, birth defects or other ... MODEL NUMBER • SERIAL NUMBER TS1141
When ordering repair parts, always give the following information:
Ryobi® is a registered trademark of Ryobi Limited used under license. Double Insulated
WARNING:
Some dust ...
Repair Sheet - Page 2
RYOBI 7-1/4 in. MODEL NUMBER TS1141
1 2
10 11
45 6 7 8
13
9
60
59 58 57
62 16
14 12
17 18 15
9
24 52
22 21 19
20
51 50
25 26
23
49
48
45 46
47
44 43
63
28
27
40 41
39
29
38
32
37
36
35
30
34
27
33 31
42
78 77 76
69
66
65
71
70
67
68
72 73
FIGURE A
79
75
74
3
61 56 55
62
56 55
53 54
63 64
2 COMPOUND MITER SAW -
Repair Sheet - Page 3
...when ordering parts. MODEL NUMBER TS1141
The model number will be found on a label attached to the motor housing. NUMBER
DESCRIPTION
PARTS LIST FOR FIGURE A
QTY
KEY PART
NO. Key Nos. 28, 39 & 42 1
24 080006014027 Dust Bag Assembly 1 25 089240001041... Warning Label 1 43 080006014038 Spindle Lock Pin 1 44 A47000040006 E-Ring 1
3
RYOBI 7-1/4 in .
Repair Sheet - Page 4
...model...'s Manual 1
2-3-11 (Rev:05)
* Use these parts for tools built after Serial Number BK102323802. Single asterisk parts (*) and Double asterisk... Number BK102323802. ** Use these parts for tools built prior to the motor housing. COMPOUND MITER... Blade (7 1/4 in . MODEL NUMBER TS1141
The model number will not interchange with each other.
4 Key Nos...
Repair Sheet - Page 5
COMPOUND MITER SAW - MODEL NUMBER TS1141
15
12
14
11 13
16 17 18
19 20
1
2 3 4
22
21
23
27
24 25
28
5
6
26
6
7
7
29
8
9
30
FIGURE B
10 36
31 32 33
34 36
35 50 53 52
51
50 49 44 43 47
5
53
52
55
59
37
54
56
38
44 43
39
40
57
42
58
41 45
46
48
47 RYOBI 7-1/4 in.
Repair Sheet - Page 6
... Label (Small 1
30 089240001011 Table 1
6 PARTS LIST FOR FIGURE B
KEY PART
KEY PART
NO.
Always mention the model number in all correspondence regarding your 7-1/4 in . NUMBER
DESCRIPTION
QTY
NO. RYOBI 7-1/4 in . COMPOUND MITER SAW or when ordering parts. MODEL NUMBER TS1141
The model number will be found on a label attached to the motor housing.
Similar Questions
Where Can I Get A Dust Bag For Bd4601/bd4601g Belt/disc Sander
(Posted by bigdogduris1 7 months ago)
Is There A Recommended Dust Bag Or Hose To Trap Dust From This Sander?
(Posted by cwepps 10 years ago)
Dust Bag For Ryobi Bs903
Is there a dust bag that fits the Ryobi BS903 band saw? If so, where can I purhase it. Lynda
Is there a dust bag that fits the Ryobi BS903 band saw? If so, where can I purhase it. Lynda
(Posted by lyndarcollier 12 years ago)