Ryobi P631K1 Support Question
Ryobi P631K1 Support Question
Find answers below for this question about Ryobi P631K1.Need a Ryobi P631K1 manual? We have 1 online manual for this item!
Question posted by robert8418 on July 31st, 2011
Is It Normal To Have Paint Leakage Behind Piston
I recently purchased a ryobi cordless paint sprayer model #P631K1 have run approx. 2 gal. of paint though it . Have seen paint leaking from behind piston and motor housing . Have tried paint thickness reduction or thinning of the paint but that seems to make it worse. What can I do to solve this problem of paint running from housing and cup?
Current Answers
Related Ryobi P631K1 Manual Pages
Operation Manual - Page 2
...30-DAY EXCHANGE POLICY: During the first 30 days after date of purchase, you may exchange any RYOBI® power tool which does not work in a reasonable time, but, in the design... a particular purpose, are limited to two years from the date of purchase. English ADDITIONAL LIMITATIONS: Any implied warranties granted under normal usage and does not cover any case, within ninety (90) days ...
Operation Manual - Page 3
... psi.
Know how to stop leaks with a minimum flash point of ignition such...60°C (140°F), do not try to result in use a spray tip...Paint or solvent flowing through the area. Read the operator's manual carefully.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL... applications and limitations as well as cigarettes, motors, and electrical equipment.
For units ...
Operation Manual - Page 4
...of personal injury.
Never leave tool running unattended. Don't leave tool until it was not designed for a ...product damage.
Never use the sprayer without a spray tip installed.
An injection injury can...tool.
Do not use tool if switch does not turn it for . Check for looseness before each use.
To reduce the risk of injury, keep paint off the motor...
Operation Manual - Page 5
... comes in contact with water immediately.
Do not charge battery tool in the locked or off position before making any cordless product in vehicles.
Under extreme usage or temperature conditions, battery leakage may cause sparks, burns, or a fire.
Battery tools do not have to be charged in a location where the temperature...
Operation Manual - Page 6
... of these symbols will result in death or serious injury. WARNING:
Indicates a potentially hazardous situation, which , if not avoided, may result in maximum gallons of paint sprayed per hour
To reduce the risk of the following signal words and meanings are intended to operate the product better and safer.
Some of...
Operation Manual - Page 7
...carefully inspected and satisfactorily operated the product.
Round Tip
Battery Pack
Charger
Tool Bag
Operator's Manual
WARNING:
If any parts are included. Any such ...hang the sprayer for use of this product requires an understanding of the paint container.
innovative motor design
The innovative motor design means less vibration and noise when using your sprayer.
integrated ...
Operation Manual - Page 8
...Place the battery pack in the tool before use of the battery ...Ryobi One+ battery pack and charger models. Use the 1 in serious personal injury. wide fan tip for the purpose listed below: Interior and exterior painting and staining of stain and paint may cause the sprayer to the Operator's Manuals for latex paints and stains. For complete charging instructions, refer to leak...
Operation Manual - Page 9
... cloths or other cover to protect areas that may be painted or stained.
Fill the quick-lock container with an even amount of paint or stain throughout, refer to the piston, follow the instructions in Cleaning the Sprayer for Storage in an idle tool for short term storage:
Remove the battery pack from...
Operation Manual - Page 10
...; Remove the battery pack from the sprayer. Remove the paint container. Remove the suction tube and filter. Remove the installed spray tip by turning it counterclockwise.
Slide the pump housing assembly/container lid forward off the sprayer.
Pull the piston and spring off the pump housing. Using the cleaning brush...
Operation Manual - Page 11
... pass to allow the motor to the surface being sprayed is loose.
Battery is getting low.
Paint/stain runs or sags on the work Proper paint methods not being sprayed. Tighten spray tip. Follow material manufacturer's directions
to access the piston for Storage to thin material as needed . Charge battery.
Thoroughly clean the sprayer using longterm storage...
Similar Questions
Replacing Motor- How Do I Replace The Motor? Have New Motor & Can't Get Housing
How do I get the motor housing off so can replace motor? Have removed two screws (each about 3" long...
How do I get the motor housing off so can replace motor? Have removed two screws (each about 3" long...
(Posted by chanburn 4 years ago)
Batteries
good day,i have a few of your drills and I have notice that the batteries are not lasting as long as...
good day,i have a few of your drills and I have notice that the batteries are not lasting as long as...
(Posted by ccarcano 9 years ago)
Drive Piston Placement
How does the drive piston get assembled insie the gear
How does the drive piston get assembled insie the gear
(Posted by monicacmurray 10 years ago)
Replacement Parts
I recently purchased a Ryobi BT3000 10" Table saw w/stand. The miter gauge for it is missing; only...
I recently purchased a Ryobi BT3000 10" Table saw w/stand. The miter gauge for it is missing; only...
(Posted by mica4339 11 years ago)
After Running A Few Minutes It Starts To Squeal. What Is The Possible Problem?
The unit continues to run and never fills to capacity. I'm guessing the pressure switch, but I could...
The unit continues to run and never fills to capacity. I'm guessing the pressure switch, but I could...
(Posted by hdryhder 12 years ago)