Ryobi P360 Support Question
Ryobi P360 Support Question
Find answers below for this question about Ryobi P360.Need a Ryobi P360 manual? We have 2 online manuals for this item!
Question posted by bassmanrrt on May 25th, 2014
My 360 Fires 5/8 Staples Without Any Problems. But When I Try To Shoot 2' 18 Ga
Porter Cable staples it won't fire. No jamed staples noted.
Current Answers
Related Ryobi P360 Manual Pages
User Manual - Page 2
... doing and use on . Protective equipment such as in unexpected situations. Cluttered or dark areas invite accidents.
Do not operate power tools in electric shock, fire and/or serious injury. A moment of moving parts. Save all instructions. For use any adapter plugs with earthed or grounded surfaces such as pipes, radiators...
User Manual - Page 3
...Use power tools only with ANSI Z87.1.
3 - BATTERY TOOL USE AND CARE
Recharge only with ANSI Z87.1. Use of staples and personal injury.
Do not point the tool towards ... the insulation of electric cables thereby causing electric shock or fire hazards.
Hold power tool by the operator and others in unexpected firing of unauthorized parts or failure...
User Manual - Page 4
... and free from trigger when not driving fasteners to be required in poor staple feeding, jammed staples, and staples leaving the tool at erratic angles. Use of electric shock, fire, or serious personal injury.
Do not place battery tools or their use the tool as serious personal injury could result in some environments. When required, the...
User Manual - Page 5
...by holding the stapler against the material. This is activated. charge area of tool. Never point tool at anyone. Do not pull the trigger or depress the workpiece ... body, especially when driving fasteners into hard or dense material.
During normal use this tool, loan them to filter out microscopic particles.
5 - English Your risk from exposure to...
User Manual - Page 6
... discharge area of injury, user must read and understand operator's manual before using this product. English Read Operator's Manual
To reduce the risk of the tool.
CAUTION:
Indicates a potentially hazardous situation, which , if not avoided, will allow you to comply with this product. This product uses nickel-cadmium (Ni-Cd...
User Manual - Page 7
... sequential actuation An actuation system in which a fastener is to be driven by the material to be activated by a tool.
WARNING:
Do not attempt to modify this product. Staple Type 1/4 in the tools within the scope of an actuation system, can occur when any operating control is released and re-activated.
English GLOSSARY...
User Manual - Page 8
...THE TOOL WITH STAPLES
See Figures 4 - 5, pages 12 - 13.
WARNING:
Keep the tool pointed away from the tool. English Removing battery pack will prevent accidental starting that a careless fraction of the tool....of the stapler, depending on the bottom of the tool helps prevent marring and denting when working with hearing protection. NOTE: Squeeze LED light grip switch to serious injuries....
User Manual - Page 9
... the workpiece contact mechanism during operation of drive, first adjust the air pressure and drive a test fastener. NOTE: Hold trigger until the desired
depth is depressed. OPERATION
Push the magazine cover closed. REMOVING STAPLES FROM THE TOOL
Remove the battery pack.
Depress the magazine release button.
Remove...
User Manual - Page 10
... in normal operating position.
NOTE: Driving too deeply into the driving mechanism
and push the driver mechanism back, freeing the jam. Remove the bent staple. Reinsert staples and close the magazine. Reinstall the battery and reactivate the tool. DRY-FIRE LOCKOUT
The dry-fire lockout feature keeps the tool from operating when fasteners are...
User Manual - Page 11
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
Work-contacting element does not Low staples depress fully - Take tool to www.ryobitools.com
NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 12 AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.
11 - For Warranty details go to nearest authorized repair center
This product has a Three-year Limited Warranty. English
tool does not operate...
User Manual 2 - Page 3
... Bumper 1
14 693099003 Connecting Rod 1
15 562961001 O-Ring 1
16 524475001 Valve Shaft 1
17 562960001 O-Ring 1
18 305684001 Drive Cylinder w/Magnet 1
19 202918001 Driver Assembly 1
20 562963001 Rubber Sleeve 1
21 661923001 Screw (M4 x ... Screw (M4 x 4 mm, Soc. MODEL NUMBER P360
The model number will be found on a label attached to the motor housing. 18 GA CORDLESS STAPLER -
User Manual 2 - Page 4
RED
RED BLACK
18 GA CORDLESS STAPLER - MODEL NUMBER P360
MICRO SWITCH
RED
BLUE
CIRCUIT BOARD ASSY
SWITCH RED
WHITE WHITE
LED LIGHTS
PADDLE SWITCH
CONTACT PLATE
WIRING DIAGRAM
4
MOTOR
Similar Questions
Striker
Striker does not push out to push nails. I oiled it but it still does not come out when the trigger ...
Striker does not push out to push nails. I oiled it but it still does not come out when the trigger ...
(Posted by Michaelalockett704 1 year ago)
Blinking Lights On A P360 Cordless Stapler
lights just blinks when I push the light button, and wont shoot when I push the trigger
lights just blinks when I push the light button, and wont shoot when I push the trigger
(Posted by Pazsiding 6 years ago)
Firing Pin On The Air Strike Brad Nailer Shoots Out Of The Brad Compartment
When unit is depressed it fires as if it is working however the firing pin is the only thing stickin...
When unit is depressed it fires as if it is working however the firing pin is the only thing stickin...
(Posted by creativearts 8 years ago)
No Apparent Problem, Not Firing
Cleared jam, due to brads not adhered together. New pack bought, newly charged battery. No sign of p...
Cleared jam, due to brads not adhered together. New pack bought, newly charged battery. No sign of p...
(Posted by Scottewing 10 years ago)