Panasonic 1100W Support Question
Panasonic 1100W Support Question
Find answers below for this question about Panasonic 1100W - Sharp 1 CF Microwave.Need a Panasonic 1100W manual? We have 1 online manual for this item!
Question posted by nderuite on July 2nd, 2012
All The Lights Went Out And It Does Not Work, Could It Be A Fuse?
The person who posted this question about this Panasonic product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Panasonic 1100W Manual Pages
Service Manual - Page 1
...SIMMC 0001002C1
E1
Service Manual Microwave Oven
Specifications for CPH:
Specifications: Power Source: Power Requirement: Output(IEC705-88): Microwave Frequency: Timer: Outside Dimensions: Oven Cavity Dimensions: Weight:
Model: NN-S560BF/WF NN-S540BF/WF NN-L530WF NN-L520WF NN-S510WF
*120V AC Single Phase, 60Hz
1370W
1370W
1370W
1370W
1200W
1100W
1100W
1100W
*2450MHz *99min.99sec *20...
Service Manual - Page 2
... and transmission systems shall be repaired, replaced, or adjusted by procedures described in the microwave oven which are special components used in this manual to avoid being exposed to microwave radiation leakage including the oven operating with the Federal Performance Standard should immediately notify the appropriate address listed below and Center for measuring radiation...
Service Manual - Page 3
...to repair Inverter PCB because it . Replace as the high voltage transformer and high voltage capacitor in ordinary microwave ovens.
2. 3.
Very high voltage may remain in high heat energy. High voltage may remain in circuit....hot in the capacitors on the Inverter board because it is off. Do not test oven while Inverter grounding plate or screws are loose. For USA only: Do not try ...
Service Manual - Page 5
.../Less Pad (13) Cooking Guide (14) Auto Cook Pad (15) Serving/Weight Pad (16) Start Pad
One tap allows oven to restart oven.
(17) Stop/Reset Pad
Before cooking: One tap clears your
instructions and time of day or colon appears on the display ...stops the cooking process. If door is opened or STOP/RESET Pad is pressed once during
oven operation, START Pad must again be pressed to begin functioning.
Service Manual - Page 6
...and will count up by minutes.
11. 25
2. When 2nd stage cooking time has elapsed, oven beeps 5 times and shuts off . Press Clock pad.
3.
Press Stop/Reset Pad twice.
...
1. Inverter Turbo Defrost
OPERATION
1. If you pluge the power supply cord into the wall outlet, microwave oven automatically enter into the state of day or colon if set Medium power. (2nd stage)
P ...
Service Manual - Page 7
...(T1) automatically switches to 4 minutes after the start pad is pressed. Press Start pad.
4.10
When cooking time has elapsed, Oven beeps 5 times and shuts off .
Time of day or colon if set appears in the display.
8. To Reset Child Lock ...the beaker or the Power source Voltage.
4.When cooking time has elapsed, Oven beeps 5 times and shuts off . NOTE: Cooking time will vary depending...
Service Manual - Page 10
The relation between indications on the control panel and the output of the microwave oven is always monitored by the signal output from the current transformer built into the... by a control signal from "Low" to DC voltage immediately. 2. One complete ON and OFF cycle of the microwave oven from the digital programmer circuit.
- 9 - DC voltage will be fed back to the microcomputer in the DPC ...
Service Manual - Page 11
...=2 min. The coefficient K is programmed Into the mlcroprocessor memory and they are listed in the microwave oven using the formula below make sure this 10 second is produced. Sensor Cooking Category
Frozen Vegetables
P1 ...by using power select and time features. Because of time it takes the microwave oven to switch to reheat refrigerator and room temperature foods. The total amount of the...
Service Manual - Page 12
...on or near these circuits with an insulated tool during servicing and replacing. The microwave oven is directly connected to the Aluminum heat sink. therefore, extreme care should be ...broken or otherwise deficient in the inverter power supply circuit board. The Aluminum heat sink may work .
2. fuse if blown due to the operation of the magnetron filament terminal.
- 11 - Never ...
Service Manual - Page 13
... repair or exchange, it is very important to procedure for measuring microwave energy leakage.)
CAUTION MICROWAVE RADIATION DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY. 6.Confirm after repair (A) After repair or replacement of the
oven, etc. Microwaves might leak if screws are not properly tightened. (B) Make sure that...
Service Manual - Page 14
... relays and install new transformer/relays making sure there is attached to prevent microwave leakage. Fan motor (A) Disconnect 2 lead wires from fan motor terminals. (B) Remove 1 screw at located on oven attaching orifice assembly. (C) Remove orifice assembly/Inverter power supply (U) from oven assembly. (Refer page 15) (D) Remove fan blade from the fan motor shaft...
Service Manual - Page 15
... door
cannot be removed if the opening angle of the door, reassemble, install, and perform microwave leakage test.
6. NOTE: After reinstalling the new turntable motor and reconnecting the two lead wires...or the like. (See Figure) NOTE: After breaking off the motor cover, make sure that no sharp edge will expose to outside. (B) Disconnect 2 lead wires connected to the turntable motor. (C) Remove ...
Service Manual - Page 16
Remove screw and slide oriffice toward you, then lift up and out.
1. Take off outer panel.
6. Detach turntable wires
from the
oven. Remove 2 screws holding inverter to leave the grounding plate in its place. 2. Push Inverter Assembly until locking tabs are locked. 12. 8. Make sure the heat ...
Service Manual - Page 17
...Switch and Secondary Latch Switch. Test 2. After approximately 27 seconds, oven displays H97 and
stops oven.
2. During oven operation, input current is present at door opened and closed positions ... is approximately 1.0 to Inverter Power Supply (U).
(C) Test the continuity of water load into oven cavity. Inverter Power Supply (U)for 1 minute and press start .
1. Inverter power supply ...
Service Manual - Page 18
If
the following test.
1) Place a water load (150 cc) in the oven. 2) Tap Sensor Reheat pad. 3) Tap Start Pad. 4) Steam Sensor detects steam about 1.5 to remaining time cooking
(T2). 6) The remaining cooking time (T2) appears in working order or not, do the following cooking time appears, Steam Sensor function is tapped. 5) T1 time...
Service Manual - Page 19
...When the 18 Amp. G5J-1-TP for short switch and Part. fuse is completed. Then follow the installation procedures below . Make sure that the oven door will
lower the magnetron output. Necessary Equipment: *1 liter beaker ...as T1). (B) Place the beaker on the center of glass cook plate. Measurement of microwave output
The output power of the magnetron can be sure mounting tabs are not bent, ...
Service Manual - Page 20
... checked for Canada) inform PASC, PSC, or PCI immediately. PROCEDURE FOR MEASURING MICROWAVE ENERGY LEAKAGE
WARNING Check for measuring radiation leakage
Note before the outer panel is ... oscillating, measure the leakage by D.H.H.S. After repairing or replacing any adjustment or repair to a microwave oven, a leakage reading must be more than 2mW/cm2 (1mW/cm 2for Canada). (5) Leakage for...
Service Manual - Page 21
... connector instead of low voltage transformer). Always touch yourself to ground while working on the digital programmer circuit (Terminals of power relay's and primary circuit...microwave oven following the correct operating procedures in power source voltage 2. SYMPTOM
1. Fuse is blown.
3. No display and no operation at all .
2. No display and no microwave oscillation. (No heat while oven...
Service Manual - Page 24
Oven is tapped
No microwave oscillation at high power
Q220 transistor
Replace display and check operation
Replace IC-1 and check ... for 1 minute and conduct following test quickly, unless H97/H98 appears and oven stops. If any power setting
Dark or unclear display
Missing or lighting of 120V
0V Approx. When the fuse pattern (PF2) opens. (1) Remove the jumper wire (PF1). (2) Insert the...
Service Manual - Page 27
... SWITCH) (D3V-1G-2C25)
1
1
S560*FAPH, S550*FAPH
1
S560*FCPH
1
S540*FAPH, L530*FAPH
1
S540*FCPG, L530WFCPH,L520WFCPH,S510WFCPH
B62308250AP B62314000AP F61844T00AP B63264080AP F900C9660AP F900C9660CP
FUSE FUSE HOLDER GROUNDING PLATE TURNTABLE MOTOR AC CORD W/PLUG AC CORD W/PLUG
1
18A/120V,60Hz
1
******APH
1
1
1
******APH
1
******CPH
A692Y4T00CP XTWANE+10RU XST4+5VS XYD4+EE12F...
Similar Questions
Panasonic Genious Premier 1100w
How do I replace the light bulb?
How do I replace the light bulb?
(Posted by planoscorp123 9 years ago)
Panasonic Nn-h765bf Microwave Purchased 2008 Troubleshooting.
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
(Posted by Kamathn 11 years ago)
My Connectionless Steamer Microwave Oven Ne-2180 Does Not Work Fuses Replaced
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
(Posted by sbenson99 11 years ago)
Nn-s530bfv Microwave Worked, Now Runs For 4 Seconds When Turned On.
the NN-S530BFV microwave worked fine to bake potatoes and now it will only run for 4 seconds and c...
the NN-S530BFV microwave worked fine to bake potatoes and now it will only run for 4 seconds and c...
(Posted by Hambydv 12 years ago)
Panasonic Nn Sd986s Microwave Oven Does Not Work After Pressing Start.
Power is on and LCD lights work. It just starts and immediately stops after setting the time then pr...
Power is on and LCD lights work. It just starts and immediately stops after setting the time then pr...
(Posted by aerospacecase 12 years ago)