Panasonic 1100W Support Question
Panasonic 1100W Support Question
Find answers below for this question about Panasonic 1100W - Sharp 1 CF Microwave.Need a Panasonic 1100W manual? We have 1 online manual for this item!
Question posted by Hambydv on April 17th, 2012
Nn-s530bfv Microwave Worked, Now Runs For 4 Seconds When Turned On.
the NN-S530BFV microwave worked fine to bake potatoes and now it will only run for 4 seconds and cuts off. How can I trouble shoot to find the problem? oven is in a camper.
Current Answers
Related Panasonic 1100W Manual Pages
Service Manual - Page 1
...
Specifications for CPH:
Specifications: Power Source: Power Requirement: Output(IEC705-88): Microwave Frequency: Timer: Outside Dimensions: Oven Cavity Dimensions: Weight:
Model: NN-S560BF/WF NN-S540BF/WF NN-L530WF NN-L520WF NN-S510WF
*120V AC Single Phase, 60Hz
1370W
1370W
1370W
1370W
1200W
1100W
1100W
1100W
*2450MHz *99min.99sec *20 "(518mm)(W)O 16 "(407mm)(D)O *14 "(375mm)(W)O 15...
Service Manual - Page 2
...specified parts to prevent microwave leakage, shock, fire, or other damage) (4) Damage to or loosening of hinges and latches. (5) Evidence of dropping or abuse
(C) Before turning on site, advise the... described in this manual before and after every servicing according to microwave radiation leakage including the oven operating with the Federal Performance Standard should be serviced only by ...
Service Manual - Page 3
... with preset volume on the board. Do not try to adjust or tamper with very high voltages and high heat energy. Do not test oven while Inverter grounding plate or screws are loose. Very high voltage and high current circuits. DO NOT:
* 1.
* 2. * 3.
*... magnetron tube with extremely high voltage
and high current.
High voltage may remain in ordinary microwave ovens.
2. 3.
Service Manual - Page 5
Another tap cancels all your instructions. NN-S540
CONTROL PANEL
NN-L530
NN-L520
1
1
2
4b
3
2
3
10 13
5
6
11
16 6
7
17
8
7
8
MN-S510
1
2
4b
3
10
5
6
11
16
...) Cooking Guide (14) Auto Cook Pad (15) Serving/Weight Pad (16) Start Pad
One tap allows oven to restart oven.
(17) Stop/Reset Pad
Before cooking: One tap clears your
instructions and time of day or colon appears...
Service Manual - Page 6
...the power source.
1. If you pluge the power supply cord into the wall outlet, microwave oven automatically enter into wall outlet. To Set Clock
OPERATION
1. SCROLL DISPLAY
Time of lb...pads. 5 sec.= 5
. 5
4. SCROLL DISPLAY
2. Set the weight for 5 seconds by pressing Number pads. 1 lb = 1 0
1.0
3. Oven shuts off .
Time of day (TOD) by minutes.
11. 25
2. Press Start pad....
Service Manual - Page 7
... )
2. SCROLL DISPLAY
2
2. Cooking begin as times counts down .
2.00
3.When cooking time has elapsed, Oven beeps 5 times and shuts off .
Power Level
Press Power Level
once twics 3 times 4 times 5 times 6...9 times 10 times
Power Level
P 10 (HIGH) P 9 P 8 P 7 (MED. Sensor Cooking (NN-S560WFAPH/CPH,S560BFAPH/CPH)
OPERATION
1. Pour 150 15cc (4.5 1/2 ozs) of room temperature water in a beaker,...
Service Manual - Page 10
... the HV diodes and Capacitors, generates the necessary 4,000V DC needed for heating of microwave power since approximately 2 seconds are required for the magnetron. 5. Variable Power Cooking
POWER SETTING
OUTPUT POWER(%) APPROX....Variable power cooking control
The coil of the microwave oven is 22 seconds. Output power of power relay B is as the H.V. DESCRIPTION OF OPERATING SEQUENCE
1.
Service Manual - Page 11
...sure this 10 second is called the steam sensor element, senses this steam builds up and eventually escapes from the cooking container placed in the microwave oven using power ...
P2 Power LOW
P2 Power LOW
K Factor Standard
0.1
K Factor Standard
0.1
- 10 - Sensor Cooking (NN-S560BFAPH/CPH NNS560WFAPH/CPH)
Auto sensor cooking is produced. T2 time (in the Auto Sensor Cooking Guide. and...
Service Manual - Page 12
.... WARNING There is grounded properly before beginning repair work as an antenna and cause microwave leakage.
Though it is high-voltage present, with an insulated handle screwdriver to the operation of the Inverter. WARNING OF DISCHARGING HIGH VOLTAGE
CAPACITORS Warning about 30 seconds after the oven is high-voltage, high current equipment. When replacing...
Service Manual - Page 13
... leak if screws are not properly tightened. (B) Make sure that the screws of the
oven, etc. The following components have potentials above 250V while the
appliance is operated with the door hinges or magnetron
fixed incorrectly, the microwave leakage can reach more than 5mW/cm2. 6.Confirm after repair (A) After repair or replacement...
Service Manual - Page 14
.... (D) Remove 4 screws holding air guide c to prevent microwave leakage. Therefore, applying hot air such as follows; Membrane key...of escutcheon base is cleaned sufficiently so that any problems (shorted contacts or uneven surface) can be ... electric charge built up on oven attaching orifice assembly. (C) Remove orifice assembly/Inverter power supply (U) from oven assembly. (Refer page 15)...
Service Manual - Page 15
...NOTE: After breaking off the motor cover, make sure that no sharp edge will expose to outside. (B) Disconnect 2 lead wires connected ... NOTE: When installing the steam sensor, make sure that cut-off
portions are properly trimmed off or bend to the ...the opening angle of the door, reassemble, install, and perform microwave leakage test.
6. After replacement of the defective component parts ...
Service Manual - Page 17
...
A. magnetron. D. After approximately 15 seconds, oven displays H98 and
stops oven. If both 1 and 2 are OK, please proceed to 1.7A. Set oven at the high voltage terminal of short...from magnetron tube. Unplug 3 pin connector, CN701
B. After approximately 27 seconds, oven displays H97 and
stops oven.
2. The contacts assignment of H97 or H98 appears by disconnecting the leads...
Service Manual - Page 18
... In order to determine if the steam sensor function of the digital programmer circuit is in working order or not, do the following cooking time appears, Steam Sensor function is tapped. 5)... cooking automatically switches to remaining time cooking
(T2). 6) The remaining cooking time (T2) appears in the oven. 2) Tap Sensor Reheat pad. 3) Tap Start Pad. 4) Steam Sensor detects steam about 1.5 to 4...
Service Manual - Page 19
... to the door hook is necessary.
(B) When mounting the door hook assembly to the oven assembly, adjust the door hook assembly by moving it for exactly one liter of tap water...switch replacement In replacing faulty switches, be determined by performing IEC standard test procedures. Measurement of microwave output
The output power of the magnetron can be sure mounting tabs are not bent, broken ...
Service Manual - Page 20
... false readings the test probe should initially be kept by holding the probe perpendicular to a microwave oven, a leakage reading must be more than 2 mW/cm2 (1mW/cm for Canada) after... record for future reference, as required by its manufacturer.
PROCEDURE FOR MEASURING MICROWAVE ENERGY LEAKAGE
WARNING Check for radiation leakage after determining that all necessary components are...
Service Manual - Page 21
... to ground while working on this control panel. First of all operate the microwave oven following the correct ...microwave oscillation. (No heat while oven lamp and fan motor turn on when oven is dead. Open or loose wiring of power relay (RY1)'s contacts (between 1 and 2) and if it , otherwise lead wire may result in with the AC plug removed. Check grounding before checking for trouble...
Service Manual - Page 22
...Open steam sensor 3.Defective DPC
Check tighten screws on the Auto sensor cooking mode.
1.
Oven stops operation during cooking.
11. Adjust door and latch switches.
- 21 - Open ... wiring of turntable motor 2. Oven does not operate and return to plugged in
1.
Defective turntable motor
1.
Oven returns to plugged in mode after 10 seconds
elapses on escutcheon base bracket,...
Service Manual - Page 23
... also DO NOT
RE-ADJUST PRESET VOLUME on the board. This oven is programmed with a new one .
* Check magnetron filament for troubleshooting
H97, H98, or H99 appears in display window a short time after start key is pressed and no microwave oscillation. Inverter problem (SEE NOTE)
NOTE: After check, unplug unit to reset to...
Service Manual - Page 24
Trouble Related to Digital Programmer Circuit
SYMPTOM No display when oven is detected, replace the defective parts. STEP 1
CHECK Fuse pattern of DPC
RESULT Normal Open ...H97/H98 appears and oven stops.
SYMPTOM No key input
No beep sound
Power relay A(RY-2) does not turn on RY-2 turns on even though the program has been set and the start pad is tapped
No microwave oscillation at high power...
Similar Questions
Microwave Glass
Wnere can I get a new glass bottom for my microwave?
Wnere can I get a new glass bottom for my microwave?
(Posted by kstiland 10 years ago)
Panasonic Nn-cf778sbpq Microwave Dcp Error Code Reset Key Sequence
I have two Panasonic NN-CF778SBPQ microwaves one that was dropped and displays the dreaded H98 error...
I have two Panasonic NN-CF778SBPQ microwaves one that was dropped and displays the dreaded H98 error...
(Posted by fra356 11 years ago)
Panasonic Nn-h765bf Microwave Purchased 2008 Troubleshooting.
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
(Posted by Kamathn 11 years ago)
All The Lights Went Out And It Does Not Work, Could It Be A Fuse?
(Posted by nderuite 11 years ago)
Panasonic Nn Sd986s Microwave Oven Does Not Work After Pressing Start.
Power is on and LCD lights work. It just starts and immediately stops after setting the time then pr...
Power is on and LCD lights work. It just starts and immediately stops after setting the time then pr...
(Posted by aerospacecase 12 years ago)