Panasonic 1100W Support Question
Panasonic 1100W Support Question
Find answers below for this question about Panasonic 1100W - Sharp 1 CF Microwave.Need a Panasonic 1100W manual? We have 1 online manual for this item!
Question posted by planoscorp123 on July 26th, 2014
Panasonic Genious Premier 1100w
How do I replace the light bulb?
Current Answers
Related Panasonic 1100W Manual Pages
Service Manual - Page 1
...
1370W
1370W
1200W
1100W
1100W
1100W
*2450MHz *99min.99sec *20 "(518mm)(W)O 16 "(407mm)(D)O *14 "(375mm)(W)O 15 "(386mm)(D)O *26.5 lbs. (12.0kg) Output power:IEC705-88 Test Procedure
11"(301mm)(H) 8 "(225mm)(H)
Specifications subject to the last page. Unauthorized copying
and distribution is a violation of law.
SIMMC 0001002C1
E1
Service Manual Microwave Oven
Specifications for APH...
Service Manual - Page 2
... manufactured in the microwave oven which are special components...replacement parts list. Any serviceman who learns of potential dangers in the interlock, monitor, door seal, and microwave generation and transmission systems shall be serviced or repaired only by procedures described in this service information by anyone else could result in serious injury or death. IN U.S.A. (PASC)
Panasonic...
Service Manual - Page 3
...2. * 3.
* 4.
* 5. Inverter Circuit (U) with extremely high voltage
and high current.
Even when replacing board, extreme care should be taken to adjust without proper test equipment. Do not try to repair it ...voltage may remain in ordinary microwave ovens.
2. 3.
Do not test oven while Inverter grounding plate or screws are loose. Replace as the high voltage transformer and high ...
Service Manual - Page 5
...stops the cooking process. If door is opened or STOP/RESET Pad is pressed once during
oven operation, START Pad must again be pressed to begin functioning. Another tap cancels all your instructions... Guide (14) Auto Cook Pad (15) Serving/Weight Pad (16) Start Pad
One tap allows oven to restart oven.
(17) Stop/Reset Pad
Before cooking: One tap clears your
instructions and time of day or colon ...
Service Manual - Page 6
... pressing Number pads. 5 sec.= 5
. 5
4. Press Start pad. If you pluge the power supply cord into the wall outlet, microwave oven automatically enter into the state of day or colon if set appers in the oven.
2. Plug the power supply cord into the digital programmer circuit and will count up by pressing appropriate Number...
Service Manual - Page 7
...minutes after the start pad is pressed. Press Start pad.
4.10
When cooking time has elapsed, Oven beeps 5 times and shuts off . SCROLL DISPLAY
2
2. Power Level
Press Power Level
once twics ...Reheat cycle begins time counts down .
OPERATION
3. SCROLL DISPLAY
3.5
1.45
When cooking time has elapsed, Oven beeps 5 times and shuts off . Press Serving / Weight pad. (Select 4. 6. 10. 14 slices...
Service Manual - Page 10
... output power of magnetron filament.
2. Output power of the microwave oven is always monitored by the digital programmer circuit, when the oven is rectified to 2,000V AC and approximately 3V AC by ..., generates the necessary 4,000V DC needed for heating of the microwave oven from "Low" to the magnetron tube from the digital programmer circuit.
- 9 - Variable Power Cooking...
Service Manual - Page 11
...a revolutionary way to cook the food. This T2 time is produced. T2 time (in the microwave oven using the formula below make sure this 10 second is to select an Auto Sensor Program before starting... NOTE: When "More" or "Less" pad is covered, this escape of time it takes the microwave oven to switch to be increased or decreased. If the food is selected, the K factor varles resulting ...
Service Manual - Page 12
... voltages. therefore, extreme care should be used when grounded.
The microwave oven is high-voltage present, with an insulated tool during operation.
WARNING...replacing or checking parts, remove the power plug from danger in the inverter power supply circuit board. Never insert a wire, nail or any other metal object through any other appliances, the microwave oven...
Service Manual - Page 13
...
appliance is operated with the door hinges or magnetron
fixed incorrectly, the microwave leakage can reach more than 5mW/cm2. 6.Confirm after repair (A) After repair or replacement of the
oven, etc. After repair or exchange, it is very important to procedure for microwave energy leakage. (Refer to check if magnetron and the door hinges...
Service Manual - Page 14
...or uneven surface) can be sure the antenna gasket is attached to prevent microwave leakage. Alignment position of the low voltage transformer and/or power relays. NOTE...NOTE: After replacement of escutcheon base is cleaned sufficiently so that any static electric charge built up on oven attaching orifice assembly. (C) Remove orifice assembly/Inverter power supply (U) from oven assembly. (...
Service Manual - Page 15
... so that the
direction of the door, reassemble, install, and perform microwave leakage test.
6. DOOR CCREEN B DOOR A DOOR KEY DOOR KEY SPRING...crucial. NOTE: When installing the steam sensor, make sure that no sharp edge will expose to outside. (B) Disconnect 2 lead wires connected to ...Replace other components. (L) Door alignment is achieved. 5. After replacement of the defective component parts of ...
Service Manual - Page 16
...screw and slide oriffice toward you, then lift up and out.
1. Detach turntable wires
from the
oven. Reconnet all wires from the
bottom of chasis (base). 3. Make sure to the aluminum heat... Take special care not to touch any lead wire to securely tighten grounding screw from inverter. Replace inverter and reassemble to leave the grounding plate in its place. 2. Make sure to inverter ...
Service Manual - Page 17
... programmer circuit. Tap POWER LEVEL B. After approximately 15 seconds, oven displays H98 and
stops oven.
RESISTOR SAND BAR
PRIMARY WINDINGS SECONDARY
Door Closed Door Opened
PCB...lead wires from Test 1
A. Inverter power supply (U).Replace as follows. It is as follows. Tap Clock 2. Tap TIMER 3. Program oven at the high voltage terminal of the respective pads...
Service Manual - Page 18
... TIME
(Remaining cooking time)
8 Sec.~23 Sec.
- 17 -
T1 TIME 1 Min. 30 Sec.~4 Min.
6. If
the following test.
1) Place a water load (150 cc) in the oven. 2) Tap Sensor Reheat pad. 3) Tap Start Pad. 4) Steam Sensor detects steam about 1.5 to remaining time cooking
(T2). 6) The remaining cooking time (T2) appears in working...
Service Manual - Page 19
...to the door hook is necessary.
(B) When mounting the door hook assembly to the oven assembly, adjust the door hook assembly by pulling the door assembly. Part No. ....
* Interlock switch replacement In replacing faulty switches, be determined by following the components test procedures.
2.
Primary latch switch and the short switch. Measurement of microwave output
The output power...
Service Manual - Page 20
... pad or set the timer and with door normally closed ...... Whenever you replace the magnetron, measure for a fully assembled oven [Before the latch switch (primary) is graduated to a microwave oven, a leakage reading must be more than 2 mW/cm2 (1mW/cm2 for a fully assembled oven with the magnetron oscillating, measure the leakage by D.H.H.S.
Leakage monitor
should...
Service Manual - Page 21
... turns on the digital programmer circuit, since static electric discharge may result in a false reading or damage to lower output and/or be replaced at all operate the microwave oven following the correct operating procedures in power source voltage 2. Fuse is opened.
1. Open low voltage transformer 4. Off-alignment of high voltage circuit
especially...
Service Manual - Page 23
...OK
refer to repair or adjust without sufficient test equipment because this point, there may be replaced with a new one .
* Check magnetron filament for troubleshooting. NOTE: DO NOT try ...time after start key is pressed and there is no microwave oscillation with a self diagnostics failure code system which will flow
STOP! This oven is opened, AC input Amperes 1 to this circuit ...
Service Manual - Page 24
...condition is tapped
No microwave oscillation at high power
Q220 transistor
Replace display and check operation
Replace IC-1 and check ... and conduct following test quickly, unless H97/H98 appears and oven stops.
Oven is as follows: 1. AC 3V
CAUSE/CORRECTIONS Membrane switch...If any power setting
Dark or unclear display
Missing or lighting of sensor
Abnormal = 0V Normal > 10~30mV
Steam...
Similar Questions
How Can I Get A Instruction Booket For Panisonic Genuis Premier Mirco Oven
i need a instruction booklet genius premier 1100 w
i need a instruction booklet genius premier 1100 w
(Posted by murielc1 8 years ago)
Microwave Glass
Wnere can I get a new glass bottom for my microwave?
Wnere can I get a new glass bottom for my microwave?
(Posted by kstiland 10 years ago)
Panasonic Nn-h765bf Microwave Purchased 2008 Troubleshooting.
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
(Posted by Kamathn 11 years ago)
My Connectionless Steamer Microwave Oven Ne-2180 Does Not Work Fuses Replaced
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
(Posted by sbenson99 11 years ago)