Optoma EW1610 Support Question
Optoma EW1610 Support Question
Find answers below for this question about Optoma EW1610.Need a Optoma EW1610 manual? We have 7 online manuals for this item!
Question posted by Sebrehl on July 13th, 2014
How To Replace Fan On Optoma Ew1610 Projector
The person who posted this question about this Optoma product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Optoma EW1610 Manual Pages
User's Manual - Page 1
...; Phillips screwdriver
• Two crescent or 3/4" open-end wrenches.
• Drill with heavy projectors.
Use them as anchors to fasten the ceiling mount to support the ceiling mount screws.
X ...-E73X
Compatible Models: Optoma EP731/732/732H/737/738/739/H30
READ THIS BEFORE YOU START
X Maximum weight limit is recommended that your location will hold the projector's weight, contact a...
User's Manual - Page 2
... the star washers.
5. Note: if you are appropriate for the type of the Phillips Projector Mount Screws (Part No. 2), secure the mount to the TOGGLER® brochure "Anchoring Solutions... Make sure you will be installed in the ball joint.
3. Y INSTALLING THE PROJECTOR MOUNT 1. Now position the projector and tighten the two ball joints firmly into place using the mount as a template...
User's Manual - Page 1
... ...21 Menu Tree...22 Image...23 Display...29 Setup...33 Options...39
Appendices 43 Troubleshooting 43
Image Problems 43 Intermission Problems 46 Projector Status Indication 46 Remote Control Problems 48 Replacing the Lamp 49 Compatibility Modes 51 RS232 Commands 52 Ceiling Mount Installation 55 Optoma Global Offices 56 Regulation & Safety notices 58
English
User's Manual - Page 2
... reliable operation of electric shock to the presence of the Canadian Interference-Causing Equipment Regulations. Servicing is required when the projector has been damaged in accordance with a dry cloth. 6. Please call Optoma to be referred to rain or moisture, does not operate
normally, or has been dropped.
B.
Do not use attachments/accessories...
User's Manual - Page 3
... . Please contact your eyes.
▀■ Warning- To reduce the risk of its life, the projector will show on pages 49-50.
▀■ Warning- When the lamp is on until the lamp module has been replaced. This remote control is in this may damage your local reseller or service center to...
User's Manual - Page 5
..., they are asked to point out something on floor or table top.
▀■ When projector is recommended to avoid the need for the presenter to enter the beam.
▀■ Ensure... all times.
▀■ Minimize standing facing into the beam. this is by ceiling-mounting the projector rather than placing it on the screen.
▀■ In order to minimize the lamp power needed...
User's Manual - Page 15
... power cord from the electrical outlet and the projector.
5. Warning Indicator
When the "LAMP" indicator lights red, the projector will see a message displayed on again after 15 seconds. The cooling fans continue to restart the projector.
4. Press the "Power" button again to turn Amber, the projector has entered standby mode. Please contact your local...
User's Manual - Page 35
...If this function to select your desired start-up screen.
On: Choose "On" to show the Optoma logo. Off: Choose "Off" to show a blank image.
Screen Type
Choose the screen type as... 16:9 the default format will auto become "4:3, 16:9, LBX, Native, AUTO" replace original format "4:3, 16:10, LBX, Native, AUTO".
(See page 29)
Start Up Logo
Use this format...
User's Manual - Page 39
... the display screen. Source Lock On: The projector will search specified connection port. Off: The projector will be locked, but the projector can still be operated by the remote control. Mute &#..." to allow for proper high altitude cooling of the projector. Keypad Lock
When the keypad lock function is lost. Operates the fans at full speed continuously to turn mute off .
User's Manual - Page 42
Brightness Mode STD: Choose "STD" to dim the projector lamp which will appear 30 hours before suggested replacement of lamp.
English 42 Lamp Reset
Reset the lamp life hour after replacing the lamp. User Controls
Options | Lamp Settings
Lamp Hours
Display the projection time.
The message will lower
power consumption and extend the...
User's Manual - Page 43
... that your projector, please refer to UXGA (1600 x 1200). 4. Appendices
Troubleshooting
If you are using . Select the "Settings" tab. 3. Click on the "Display" icon. 2. Please
refer to the "Replacing the lamp"...connectors are using a PC:
For Windows 95, 98, 2000, XP: 1. If the projector is lower than or equal to the following information. If a problem persists, please contact ...
User's Manual - Page 46
...replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on , 0.25s off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power. Projector ...)
Lamp-LED (Red)
Error (Over Temp.) Error (Fan fail) Error (Lamp fail)
Flashing (0.25s on pages 49-50. If this happens, the projector will burn out and may
make a loud popping sound....
User's Manual - Page 47
Appendices
Message Reminders Fan failed: Temperature warning:
Replacing the lamp: Out of range: (refer to page 51)
47 English
User's Manual - Page 48
... the batteries are no obstructions between the remote
control and the projector. Appendices
Remote Control Problems
If the remote control does not work Check the operating angle for the remote control is approximately
±22.5°.
Make sure there are inserted correctly. Replace weak batteries in the remote control.
User's Manual - Page 49
Make sure the projector has been cooled down before changing the lamp. The bulb may be used to cool down for at ... is recommended to change the lamp as soon as possible. When the lamp life is dropped.
49 English
Appendices
Replacing the lamp
The projector automatically detects the lamp life.
When you will receive a warning message. Warning: If ceiling mounted, please use , you ...
User's Manual - Page 50
... unscrew the 2 screws from the cover. 5. Push up the lamp handle carefully. 8. Appendices
1
3
5
2
4
5
Lamp Replacement Procedure: 1. Switch off the power to cool down for at least 30 minutes. 3. Allow the projector to the projector by pressing the "Power" button. 2. Use a screwdriver to unscrew the 2 screws from the lamp module. 7. Lamp...
User's Manual - Page 54
...
7E 30 30 31 35 31 20 31 0D Model name
OKn
n : 0/1/2/3/4 EP721 / EP723 /
EP727/EP728/EW1610 Appendices
English
54
SEND to emulate Remote
~XX140 1
7E 30 30 31 34 30 20 31 0D
Power
~XX140 ...0D
Color Temperature
~XX129 1
7E 30 30 31 32 39 20 31 0D
Projection Mode
SEND to projector
232 ASCII Code HEX Code
Function
Description
~XX72 1
7E 30 30 37 32 20 31 0D
Menu...
Datasheet - Page 1
...
Projection Distance 3.9' to 39.4' (1.2 to be the best all-around presentation tool. EW1610 − Multimedia Projector
Datasheet - It has the latest color processing technologies, features and connectivity options to 12m...friendly remote control with widescreen laptops and DVD content. EW1610
Set It and Play It
The Optoma EW1610 has a native 16:10 aspect ratio and a high brightness level ...
Brochure - Page 2
EW1610 | Multimedia Projector
Projection Distance/Image Size
Projection Distance (Feet)
Maximum Diagonal (Inches)
Minimum Diagonal (Inches)
3.9
35.9
32.8
9.8
89.9
81.9
16.4
149.8
136.6
23
209.7
191.2
29.5
269.6
...
Protocol Function - Page 3
...32 38 20 31 0D
Color Temperature
~XX129 1
7E 30 30 31 32 39 20 31 0D
Projection Mode
SEND to projector
232 ASCII Code HEX Code
Function
Description
~XX72 1
7E 30 30 37 32 20 31 0D
Menu Location
Top Left
~XX72...
~XX151 1
7E 30 30 31 35 31 20 31 0D Model name
OKn
n : 0/1/2/3/4 EP721 / EP723 /
EP727/EP728/EW1610 Position
n= -5 - +5
~XX76 n
7E 30 30 37 36 20 a 0D
V.
Similar Questions
I Have A Optoma Ep721 Projector And Need To Replace The Dmd Chip Any Suggestions
I have a optoma EP721 projector and need to replace the dmd chip any suggestions on what type or mod...
I have a optoma EP721 projector and need to replace the dmd chip any suggestions on what type or mod...
(Posted by Bseman 11 years ago)
Just Replaced Bulb Of Optoma Hd70. Now Projector Won't Start. Is There A Reset
Just replaced bulb of Optoma HD70. Now projector won't start. Is there a reset?
Just replaced bulb of Optoma HD70. Now projector won't start. Is there a reset?
(Posted by jschmitrz 11 years ago)
Replaced The Lamp Power Button It Went Solid Green Then 2 Red Lights Came On
(Posted by Anonymous-47434 12 years ago)
Http://www.helpowl.com/p/optoma/ew1610/116328 Parts List?
Isearch forparts behind light metal hole and lents?
Isearch forparts behind light metal hole and lents?
(Posted by alainlarocque 12 years ago)