Lowrance Elite-5 Ti Support Question
Lowrance Elite-5 Ti Support Question
Find answers below for this question about Lowrance Elite-5 Ti.Need a Lowrance Elite-5 Ti manual? We have 1 online manual for this item!
Question posted by Johnp49077 on July 27th, 2016
My Elite5ti. Gps Quit Working After Useing It The 2nd Time ?????
my elite 5 TI gps quit working after useing 2nd time ????
Current Answers
Related Lowrance Elite-5 Ti Manual Pages
Installation Manual - Page 3
...the English language version of the manual. Regulatory statements
This equipment is solely responsible for use the equipment in a manner that will be reflected in international waters as well as a...the right to make changes to the product at the time of printing.
In case of any further assistance. Preface | ELITE Ti Installation Manual
3 It is supplied as coastal sea areas...
Installation Manual - Page 4
... reception, which can radiate radio frequency energy and, if not installed and used in a particular installation.
The relevant Declaration of conformity is cautioned that the...modifications not expressly approved by turning the equipment off
4
Preface | ELITE Ti Installation Manual This equipment generates, uses and can be determined by the party responsible for license exempt devices...
Installation Manual - Page 5
Estonia FI - Italy LV - Liechtenstein LT - Poland PT - Romania SK - Denmark EE - Germany GR - Slovak Republic
Preface | ELITE Ti Installation Manual
5 Austria BE - Belgium BG - Norway PL - France DE - Lithuania LU - Cyprus CZ - Hungary IS - Czech ... receiver • Consult the dealer or an experienced technician for help
Countries of intended use in the EU
AT -
Installation Manual - Page 6
...® is a registered trademark of JL Marine Systems, Inc. Fishing Hot Spots® is used by Richardson's Maptech. Spain SE - Switzerland...; StructureScan® HD (StructureScan HD)
6
Preface | ELITE Ti Installation Manual Turkey UK - Wi-Fi® is a registered trademark of the National Marine Electronics Association.
Power-Pole® is a registered trademark of ...
Installation Manual - Page 7
About this manual
This manual is emphasized as follows:
Ú Note: Used to draw the reader's attention to equipment/ personnel.
Warning: Used when it is necessary to warn personnel that requires special attention from the reader is a reference guide for installing the ELITE Ti. Preface | ELITE Ti Installation Manual
7 Important text that they should proceed carefully to...
Installation Manual - Page 9
...
26 Wiring 26 Guidelines 27 Power connection 27 Transducer connection 28 NMEA 2000 backbone 30 NMEA 0183 device connection
31 Software Setup 31 First time startup 31 Time and Date 32 Data source selection 34 Device list 34 Diagnostics 36 Damping 36 Sonar setup 38 StructureScan 38 Autopilot setup 38 Fuel setup...
Installation Manual - Page 12
...GPS receiver (10Hz) and supports Insight charts from Navionics and Jeppesen as well as content created by a variety of available charts, visit gofreeshop.com, c-map.jeppesen.com, or navionics.com.
The ELITE... screen 2 Pages 3 Zoom out / Zoom in CHIRP/Broadband and StructureScan sonar. The ELITE-5Ti and ELITE-7Ti can network over NMEA 2000, this allows access to the vessel with the supplied ...
Installation Manual - Page 14
... opened by flipping back the logo and pulling the rubber cover open.
14
Overview | ELITE Ti Installation Manual CHIRP, Broadband, DownScan and SideScan
imaging
Card reader
Used for detailed chart data, software updates, transfer of user data, and system backup. ELITE-7Ti rear connections
12
3
1 Power (12 V supply input) and NMEA 0183 2 NMEA 2000...
Installation Manual - Page 16
... ensure satisfactory reception. Warning: Inadequate ventilation may affect the internal GPS receiver. Installation | ELITE Ti Installation Manual 3
16
Installation
Mounting location
Choose the mounting locations ... The chosen location should be mounted so that any part where it can be used as a hand hold, where it might be subjected to +131° ... marine electronics installer.
Installation Manual - Page 17
... suited to the bracket. Snap the unit to the mounting surface material. If the material is used in the desired mounting location. The dust from many materials commonly used . Use only 304 or 316 stainless steel fasteners.
3.
Installation | ELITE Ti Installation Manual
17 Screw down the bracket.
4. Place the bracket in boat construction may exceed...
Installation Manual - Page 19
... to the Mounting Template.
4. Drill all marked pilot holes. Installation | ELITE Ti Installation Manual
19 Check the Mounting Template for scaling accuracy, using a tape measure or ruler against the ruler printed on the template.
2.... and hold the release handle and then pull the unit from the bracket. Using a fingernail or small flat screwdriver, pry off the corner clips at the slotted points located...
Installation Manual - Page 20
... supplied). Sealant should be of a 'neutral cure' type to prevent damage to the mounting template. Press the four corner clips back into position.
20
Installation | ELITE Ti Installation Manual For recommended screw size and type, refer to the plastics.
7. 6. Secure the unit with the mounting surface.
8. Once screws are fully tightened, ensure...
Installation Manual - Page 22
Warning: Read all times, and in a location that has a smooth flow of water while the boat is to stay clear of propeller and hull generated turbulence, while mounting the transducer as close to the center of the vessel as possible.
22
Mounting the transducer | ELITE Ti Installation Manual Separate instructions for mounting a transom mount...
Installation Manual - Page 24
Drill a 25 mm (1") hole above the waterline, large enough to transom, using supplied stainless steel fasteners. Drill pilot holes to allow for transducer height adjustment. Attach transducer to pass the plug through.
24
Mounting the transducer | ELITE Ti Installation Manual Mark drilling points in the middle of the hull. Hold the transducer with bracket...
Installation Manual - Page 31
... settings that require configuration.
Respond to the setup wizard prompts to select some initial configuration before use, in the Operator Manual. Software Setup | ELITE Ti Installation Manual
31 6
Software Setup
This unit requires some fundamental setup options.
First time startup
When the unit is the Tools panel. Selecting the Home button opens the Home...
Installation Manual - Page 32
... NMEA 0183 is used, complete the NMEA 0183 setup prior to the system. The data may already have been selected at first time startup, however it should be suitable for example internal GPS or sonar), or external modules connected to the NMEA 2000 or via NMEA 0183 if available on the ELITE-7Ti only...
Installation Manual - Page 40
... above, one engine at least several liters (a few gallons) have been used by the number of 8 engines is supported using Fuel Flow sensors.
With the use of the Fluid Level devices.
40
Software Setup | ELITE Ti Installation Manual 1. Select the Calibrate option. 4. The Fuel K-Value should ... and set in any equipped tank. The number of fuel added
to save settings. After at a time.
Installation Manual - Page 44
...Refer to their use.
NMEA 2000 ...DHCP device may be operational on a network, dhcp_probe may also be run from the ELITE Ti. Navico is not the original developer of these tools, and cannot provide support related ...DHCP Probe are tools provided for all DHCP servers on the same network at a time. Bluetooth wireless technology
The unit includes built-in the network may be acting as ...
Installation Manual - Page 47
...Waypoints, Routes, and Trails, or export only those contained within a specific region.
Software Setup | ELITE Ti Installation Manual
47 Follow the instructions on 3. to add or improve features, to fix software bugs...inserted in the Waypoint key during power on the website: lowrance.com The unit may be used to apply software updates to itself, and to the unit itself, be backed up 4.
...
Installation Manual - Page 48
... Gen2, HDS Gen2 Touch, HDS Gen3, GO XSE units, Vulcan units, and ELITE Ti units).
• User data file version 3 (with depth): Use with legacy GPS chartplotters.
• User data file version 2 (no depth): Use with legacy GPS chartplotters.
• GPX (GPS Exchange, no depth): Use with current units (NSO evo2, NSS evo2, NSS, NSO, NSE, Zeus, Zeus...
Similar Questions
Can't Get The Depth To Move From 60ft?
can't get the depth finder to change from 60ft. Temp works though
can't get the depth finder to change from 60ft. Temp works though
(Posted by toddpugesek 10 months ago)
I Installed My Hook 7the Way The Paperwork Said One Time Just Had Gps And Maps N
(Posted by curtmimi 1 year ago)
My Fish Hunter 3d Worked Great With My Iphone 6s. Now I Upgraded To The Iphone 1
now that I have the iPhone 12 I can connect WiFi for 3 seconds and then it disconnects and I get a y...
now that I have the iPhone 12 I can connect WiFi for 3 seconds and then it disconnects and I get a y...
(Posted by Tikiray1 2 years ago)
My Gps Is Not Working. I Have Tried To Reset The Wizarthe Sonar Is Working Good.
(Posted by gequip56 2 years ago)
Getting The Lowrance Elite-4 Dsi To Work Once Wired
lowrance was wired accaccording to wireing diagram, powered up the lowrance elite is displayed and w...
lowrance was wired accaccording to wireing diagram, powered up the lowrance elite is displayed and w...
(Posted by vespree 9 years ago)