Kenmore 6962 Support Question
Kenmore 6962 Support Question
Find answers below for this question about Kenmore 6962 - 600 7.0 cu. Ft. Capacity Electric Dryer.Need a Kenmore 6962 manual? We have 1 online manual for this item!
Question posted by Ladybug65908 on February 2nd, 2023
Something Fell Down Lint Trap
I was pulling out the lint trap to clean it. Something fell down the trap and I don't know what it was. Now it is making a horrible noise. How can I get it out of the trap?
Current Answers
Answer #1: Posted by MercedesAMG on February 2nd, 2023 4:19 PM
MercedesAMG
Member since:
January 26th, 2013 Points: 193,710
Member since:
January 26th, 2013 Points: 193,710
To retrieve the object that fell into the lint trap, you can try the following steps:
- Turn off the dryer and unplug it to ensure safety.
- Locate the lint trap and remove it.
- Check the inside of the trap and the surrounding area for the object that fell in.
- If the object is visible, use a pair of pliers to carefully retrieve it.
- If the object is not visible, try using a flashlight to search for it.
- If the object cannot be found, you may need to partially disassemble the dryer to access the area where the lint trap is located.
If you're unsure of the steps or not confident in your ability to complete them, it's best to consult with a professional appliance repair technician.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Answer #2: Posted by SonuKumar on February 2nd, 2023 8:34 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,810
Member since:
May 9th, 2021 Points: 16,617,810
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Kenmore 6962 Manual Pages
Installation Instructions - Page 1
... DE LA SECADORA ...12 DE INSTALACION ...12 t2 t2 t3 15 INSTRUCCIONES Herramientas y piezas ...Requisites de lecalizaci6n ...Requisites el6ctricos ...Cenexi6n el6ctrica ... 27 IN. (69 CM) ELECTRIC DRYER INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACION PARA LA SECADORA ELECTRICA DE 27 PULG. (69 CM)
Table of others .
These words mean: You can happen if the...
Installation Instructions - Page 2
... Service Center.
For closet installation, with a door, minimum ventilation openings in the top and bottom of the dryer. Louvered doors with elbow. See "Venting Requirements." INSTALLATION INSTRUCTIONS
• • A grounded electrical outlet located within 2 ft (61 cm) of either side of the door are required. The combined weight of an automatic cycle. Install...
Installation Instructions - Page 3
...ground conductor connected to the NEUTRAL (white or center wire) of the wiring harness at least 4 ft (1.22 m) long, must have a proper outlet installed by direct wire: Power supply cable must...30R. The plug must conform to the equipment-grounding terminal or Head on the dryer.
• •
Electrical
To properly install your dealer. • Special provisions must match power supply ...
Installation Instructions - Page 4
...have a tight fit with the dryer cabinet and be connected green ground...Use a UL approved Disconnect strain wire, retief,
power before making emectdcamconnections.
Ground wire (green or bare wire) must be ... in a horizontal position.
5 6
Now complete installation following instructions of electrical connection: 4-wire (recommended)
!. 2. 3. 4. 5. 6. Connect neutral wire (white or center...
Installation Instructions - Page 5
Electrical Connection Options If your home has: And you will be connecting to: A UL listed, 120/240 volt amp., dryer power supply minimum, 30 cord* A fused disconnect or circuit breaker box* A UL listed, 120/240 volt amp., dryer... block.
...) I'_' I
* If local codes do not permit the use of dryer rear panel. Center silver-colored terminal block screw 3. Neutral grounding wire (green/yellow...
Installation Instructions - Page 6
Direct wire cable must have 5 ft (1.52 m) of the other power supply cable wires under the center screw of NEUTRAL ground wire before being moved to ... Neutral wire (white or center wire) Neutral grounding wire (green/yellow)
Place the hooked ends of extra length so dryer can be moved if needed. Insert tab of terminal block cover into slot of wires into a hook shape. Shape ends of...
Installation Instructions - Page 7
... squeeze hooked end together and tighten screw.
Strip 31/2in. (8.9 cm) of dryer rear panel. Shape ends of wires into slot of outer covering from external ground ...tab of terminal block cover into slot of extra length so dryer can be moved if needed. Direct wire cable must have 5 ft (1.52 m) of dryer rear panel.
See following example. 1. Secure cover with outer ...
Installation Instructions - Page 8
... avoid sagging and kinking that may resumt in its final position.
The dryer exhaust must be at least 12 in reduced airflow and poor performance....as flowers, rocks or bushes, etc.). If using an existing vent system, clean lint from your local Sears store or Sears Service Center. Failure to an adequate ground... and make sure exhaust hood is not plugged with a magnetic latch.
Installation Instructions - Page 9
...the exhaust vent outside.
/
FaiBure to the manufacturer's instructions. When using elbows or making turns, allow as much room as possible. Refer to follow these instructions can be ...one of elbows and turns. Bottom exhaust installation
Determine Vent Length 1. Optional exhaust installations This dryer can result in . (127 cm) mismatch Special provisions for your moca{dealer. NOTE:...
Installation Instructions - Page 10
... Box or Iouvered hoods 64 ft (20 m) 36 ft (11 m) 54 ft (16.5 m) 31 ft (9.4 m) 44 ft (13.4 m) 27 ft (8.2 m) 35 ft (10.7 m) 25 ft (7.6 m) 27 ft (8.2 m) 23 ft (7 m) Angled hoods 3. 58 ft (17.7 m) 28 ft (8.5 m) 48 ft (14.6 m) 23 ft (7 m) 38 ft (11.6 m) 19 ft (5.8 m) 29 ft (8.8 m) 17 ft (5.2 m) 6. 4 Rigid metal Flexible metal 21 ft (6.4 m) 15 ft (4.6 m) Gently lay the dryer on the corner posts until...
Installation Instructions - Page 11
... line.
2. 3.
11. Make sure the vent is level. (See "Level Dryer.") Plug into final position. When the dryer has been running or "On" position. NOTE: You may be sure all packaging materials. Turn power on
Check the levelness of the dryer. Do not crush or kink vent. Set the dryer on the dryer.
2. 3. 4. 5. 6. Electrical supply is first...
Similar Questions
How To Open Front Panel
How do you open the front panel of Kenmore gas dryer 98042
How do you open the front panel of Kenmore gas dryer 98042
(Posted by 2rnzrus 1 year ago)
Dryer Vent Positioning
Where is the vent positioned on the back of an 8787 HE3 7.0Cu Ft Electric Dryer?
Where is the vent positioned on the back of an 8787 HE3 7.0Cu Ft Electric Dryer?
(Posted by monte20536 1 year ago)
Diasble Buzzer On Kenmore 8041
How do I go about diabling the buzzer on the Kenmore 8041 5.8 CU FT electric dryer?
How do I go about diabling the buzzer on the Kenmore 8041 5.8 CU FT electric dryer?
(Posted by dhuard22 9 years ago)
I Have A Kenmore 600 Series Dryer And I Am Going From A 4 Prond Cord To A 3 Pron
do i need to attach a 10g wire from ground screw to center white neutral wire
do i need to attach a 10g wire from ground screw to center white neutral wire
(Posted by dentonkola 11 years ago)
How To Clean Cabinet Of Kenmore 6962 Dryer
How do I check the Kenmore 6962 Dryer for lint build up on the inside of the appliance? Does the bac...
How do I check the Kenmore 6962 Dryer for lint build up on the inside of the appliance? Does the bac...
(Posted by Anonymous-57868 12 years ago)