Kenmore 6962 Support Question
Kenmore 6962 Support Question
Find answers below for this question about Kenmore 6962 - 600 7.0 cu. Ft. Capacity Electric Dryer.Need a Kenmore 6962 manual? We have 1 online manual for this item!
Question posted by Anonymous-57868 on April 28th, 2012
How To Clean Cabinet Of Kenmore 6962 Dryer
How do I check the Kenmore 6962 Dryer for lint build up on the inside of the appliance? Does the back piece come off on this model? (I realize the power must be disconnected first)
Current Answers
Related Kenmore 6962 Manual Pages
Installation Instructions - Page 1
... if the instructions are very important.
many important safety messages in this manual and on your appliance. You can be killed or seriously injured if you and others are not followed.
3979976 27 IN. (69 CM) ELECTRIC DRYER INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACION PARA LA SECADORA ELECTRICA DE 27 PULG. (69 CM)
Table...
Installation Instructions - Page 2
... 2 ft (61 cm) of either side of the door are acceptable. Drying times can resumt in garages, closets, mobile homes, or sleeping quarters. Check existing electrical supply and venting and see "Electrical Requirements" and "Venting Requirements" before purchasing parts.
Proper installation is recommended to do not permit, installation of the dryer is your local building inspector. Check...
Installation Instructions - Page 3
... (n accordance with upturned ends. All current-carrying wires must be plugged into the dryer. Check with a 3-wire, cabinet-ground conductor connected to the NEUTRAL (white or center wire) of the wiring harness at least 4 ft (1.22 m) long, must determine the type of electrical connection you are in mobile homes to the neutral wire, see "Optional...
Installation Instructions - Page 4
... with the dryer cabinet and be connected green ground connector, Connect remaining 2 terminals (gold)= Securely tighten 2 suppmy wires to remaining to center terminal (simver). Put power supply cord ...wire is not available)
Power Supply Cord
DirectWire
Fire Hazard Use t0 gauge somid copper Use a UL approved Disconnect strain wire, retief,
power before making emectdcamconnections.
Connect...
Installation Instructions - Page 5
... connecting to: A UL listed, 120/240 volt amp., dryer power supply minimum, 30 cord* A fused disconnect or circuit breaker box* A UL listed, 120/240 volt amp., dryer power supply minimum, 30 cord* 3-wire direct A fused disconnect or circuit breaker box* Go to outer terminal block screws. Remove appliance ground wire (green with yellow stripes) from external ground...
Installation Instructions - Page 6
...power supply cable under the screw of power supply cable to center terminal block screw 2. External ground connector - 3=
4-wire connection:
Direct Wire 4.
Direct wire cable must have 5 ft (1.52 m) of dryer.... 1. 2. Remove appliance ground wire (green with hold-down screw. 3-wire connection: Power supply cord
Use where local codes permit connecting cabinet-ground conductor to the...
Installation Instructions - Page 7
...dryer rear panel. See following example. Remove appliance ground wire (green with hold -down screw. 3-wire connection: Direct Wire cabinet...hook facing right). Tighten screws.
!! !! Direct wire cable must have 5 ft (1.52 m) of wires into a hook shape. 4. 5. Remove center ...other power supply cable wires under center, silver-colored terminal block screw. Shape ends of extra length so dryer ...
Installation Instructions - Page 8
... must not be fully extended and supported when the dryer is recommended to prevent rodents and insects from the entire length of a building. Do not use plastic or metal foil vent. ...crushing and kinking. If using an existing vent system, clean lint from entering the home. Failure to connect elbows Exhaust outlet 4. 5. 6. The dryer exhaust must be connected into slot of the exhaust (such...
Installation Instructions - Page 9
... alternate installations are shown. Two close-clearance installations are available for close clearances
Venting systems come in . (45.72 cm) mismatch
®
Fire Hazard Cover unused exhaust kits: ... of elbows used.
Standard rear offset exhaust installation 2. Optional exhaust installations This dryer can result in . (127 cm) mismatch Special provisions for your moca{dealer...
Installation Instructions - Page 10
.... Find the diamond marking. Do not use a large flat piece of elbows you can result in the Vent Length Chart. To determine maximum exhaust length, add 1 90 ° turn inside exhaust hood. Use caulking compound to the chart.
10
Slide the dryer on the corner posts until it is close to finish turning...
Installation Instructions - Page 11
... tight; Turn power on
Check the levelness of all parts are no heat, contact a qualified technician. Set the dryer on a full heat cycle (not an air cycle) for the dryer. If the dryer will go back through the steps to level the dryer again after it is still no kinks in . (10.2 cm) clamp. Electrical supply is...
Installation Instructions - Page 24
...that you need to do-it ! and Canada)
Our Home
For repair of all major brand appliances,
... Your Home
For repair-in U,S.A, Impreso en EE, UU, For Sears professional installation of... or night (U.S.A. TM SM • ® Registered Trademark / Trademark / Service Mark of home appliances ancl items like vacuums, lawn equipment,
and electronics, call or go on a product serviced
by Sears...
Similar Questions
How To Open Front Panel
How do you open the front panel of Kenmore gas dryer 98042
How do you open the front panel of Kenmore gas dryer 98042
(Posted by 2rnzrus 1 year ago)
Something Fell Down Lint Trap
I was pulling out the lint trap to clean it. Something fell down the trap and I don't know what it w...
I was pulling out the lint trap to clean it. Something fell down the trap and I don't know what it w...
(Posted by Ladybug65908 1 year ago)
Dryer Vent Positioning
Where is the vent positioned on the back of an 8787 HE3 7.0Cu Ft Electric Dryer?
Where is the vent positioned on the back of an 8787 HE3 7.0Cu Ft Electric Dryer?
(Posted by monte20536 1 year ago)
Diasble Buzzer On Kenmore 8041
How do I go about diabling the buzzer on the Kenmore 8041 5.8 CU FT electric dryer?
How do I go about diabling the buzzer on the Kenmore 8041 5.8 CU FT electric dryer?
(Posted by dhuard22 9 years ago)
I Have A Kenmore 600 Series Dryer And I Am Going From A 4 Prond Cord To A 3 Pron
do i need to attach a 10g wire from ground screw to center white neutral wire
do i need to attach a 10g wire from ground screw to center white neutral wire
(Posted by dentonkola 11 years ago)