Husqvarna YTH18542 Support Question
Husqvarna YTH18542 Support Question
Find answers below for this question about Husqvarna YTH18542.Need a Husqvarna YTH18542 manual? We have 2 online manuals for this item!
Question posted by drcross3 on December 14th, 2019
Deck Removal
how do I remove blade tensioner spring off to remove the deck
Current Answers
Answer #1: Posted by Odin on December 14th, 2019 5:49 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
See https://isn.page.link/a5Dq. If the issue persists or if you require further advice, you'll have to consult the manufacturer, for which use the contact information at https://www.contacthelp.com/husqvarna/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Husqvarna YTH18542 Manual Pages
Owners Manual - Page 2
...over if a wheel is clear of bystanders before cleaning the machine, removing the grass catcher, or unclogging the discharge chute.
• Operate machine...Slow down a hill in the manual before dismounting.
• Disengage blades when not mowing. Do not shift to cool before and while backing...for all times.
• Only allow the mower deck to plow leaves or other debris which can affect ...
Owners Manual - Page 3
... of ignition.
•
• Use only approved gasoline container.
•
• Never remove gas cap or add fuel with the engine running .
• Check grass catcher components and ...a truck or
trailer bed with the blades shut off. Check their proper operation regularly.
• Keep machine free of bystanders before operating a riding lawn mower. SERVICE
SAFE HANDLING OF GASOLINE
...
Owners Manual - Page 5
... Lift hood to press clutch/brake pedal all accessible loose parts and parts cartons from carton.
• Remove end panels and lay side panels flat.
• Check for charging instructions.) • For battery and ... the factory with exception of this manual for any additional loose parts or cartons and remove. ING BATTERY" in the Service and Adjustments section in this manual, it means when...
Owners Manual - Page 6
... of other people and objects. Correct tire pressure is important for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual).
✓ It is ...tractor off skid.
• Remove banding holding the deflector shield up against tractor. TO ROLL TRACTOR OFF SKID (See Operation section for shipping purposes. CHECK DECK LEVELNESS
For best cutting results,...
Owners Manual - Page 9
... gases may cause engine to "backfire".
• Turn ignition key (F) to "STOP" position and remove key. B
C
ENGINE -
• Move throttle control (D) to neutral position.
CAUTION: Always stop...OPERATION
The operation of grass. NOTE: Failure to move throttle control to stop mower blades, place attachment clutch control
in brake position. To eliminate this possibility, always stop ...
Owners Manual - Page 10
... (63,5 mm) during hot months. TO STOP MOWER BLADES
Disengage attachment clutch control. J
TO ADJUST GAUGE WHEELS (...move motion control lever to desired position. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance... (25,4 to 101,6 mm). Gauge wheels then keep the deck in proper position to help prevent scalping in same adjustment hole....
Owners Manual - Page 15
... guard.
• Disconnect BLACK battery cable first then RED battery cable and remove battery from your hands with gloves and/or wrap blade with heavy cloth. • Remove blade bolt by turning counterclockwise. • Install new or resharpened blade with grease or petroleum jelly.
NOTE: Protect your local parts dealer.
TO CLEAN BATTERY AND TERMINALS...
Owners Manual - Page 16
...drain hole may be sure fan blades are intact and
clean. • Inspect cooling fins for accurate reading. LOWER DASH COVER
FASTENER
TABS
SLOTS
Fig. 17 • Remove oil fill cap/dipstick. Tighten...slip from running or while the transmission is not required for 50 hours in lower dash and remove. MAINTENANCE
V-BELTS
Check V-belts for checking level. The belts are not broken. • ...
Owners Manual - Page 17
...wheels free of drive. Use compressed air or a leaf blower to remove grass, leaves and trash from "Lower dash cover removal" section of this manual. AIR FILTER
Your engine will shorten the ... port (if equipped), we do not recommend using a garden hose or pressure washer to carburetor, replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new...
Owners Manual - Page 18
... the tractor to help dry before putting the tractor away. Turn the water off .
MAINTENANCE
DECK WASHOUT PORT (See Fig. 22)
Your tractor's deck is equipped with your tractor's Operator's Manual) onto the end of your garden hose.
4. Remove bagger chute or mulch cover if attached.
2. IMPORTANT: Make certain the tractor's discharge chute is...
Owners Manual - Page 19
... to its lowest position. remove retainer
spring and washer. • ...blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it is on level surface and engage parking brake. • Lower attachment lift lever to its lowest position. • Roll belt off engine pulley (M) and belt keepers (G). • Remove retainer spring...
Owners Manual - Page 21
A
FRONT-TO-BACK ADJUSTMENT (See Figs. 31 & 32) IMPORTANT: Deck must be level side-to clear adjustment nut B. • With a ...• If adjustment is not adjusted properly. Protect your lawn appears
unevenly cut, determine which side of tractor. ment nut (B) clockwise ( ) (tighten) to raise the front of mower. B
A
CAUTION: Blades are sharp.
B
B
TURN NUT RIGHT TO RAISE MOWER...
Owners Manual - Page 22
... wheels rotate, then the brake needs to front, over cooling fan blades (D).
• Remove belt downward from engine pulley (E).
• Slide belt toward rear of...brake. 2.
You may be replaced without tools. Contact a qualified service center. BELT REMOVAL • Remove mower (See "TO REMOVE MOWER" section
in this manual). BELT INSTALLATION • Install new belt from tractor....
Owners Manual - Page 23
...set front wheel toe-in axle groove.
• Replace axle cover. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from ... control lever has been preset at the factory and is needed to get to adjustment bolt, move mower deck height to the lowest position.
Owners Manual - Page 27
... mandrels to open vent holes. Shift to ROS "ON" position. Level mower deck.
5. Replace blade. Faulty light switch. 4. Replace battery. 2.
Obstruction in transmission during
shipment or...If not corrected, contact an authorized service center/ department. Remove obstruction. 2. Worn, bent or loose blade.
6. Replace motion drive belt. 4. Engine dies when tractor...
Owners Manual - Page 30
...as belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp wheels... questions concerning this Limited Warranty.
(a) Abrasion to mower decks;
(b) Tires damaged by external punctures; (c) Natural discoloration...(k) Tampering with improperly installed/removed or modified cutting shields, guards, or safety devices;
(m) Any removed/damaged air filter, excessive...
Parts Manual - Page 3
...MATING SIDE)
3
HEADLIGHTS
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING... CYL.
NON-REMOVABLE CONNECTIONS
REMOVABLE CONNECTIONS BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. TRACTOR - - MODEL NUMBER YTH18542 (96043018400), PRODUCT...
Parts Manual - Page 7
... 532 43 97-46 182 532 40 68-59 183 874 52 05-20
DESCRIPTION
Applique Sub Asm. Deck Lift Vent Side Hood RH Vent Side Hood LH Vent Top Hood Skirt Side RH Skirt Side LH Bezel... RH Nut Lock Hex Flange 5/16-18 Plug Dash Console Asm. inches 1 inch = 25.4 mm
7 MODEL NUMBER YTH18542 (96043018400), PRODUCT NO. 960 43 01-84
CHASSIS
KEY PART NO. Fender Crgo Dash Lower Bolt 5/16-18 x 1-1/4 Full Thd
KEY ...
Parts Manual - Page 13
MODEL NUMBER YTH18542 (96043018400), PRODUCT NO. 960 43 01-84... Flange Lock 5/8-11 Draglink, LH Draglink, RH Screw 5/16-18 x 3/4 Retainer Clip Spring Steering Bolt Hex Fghd 7/16-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/16-14 Gr. 5 Washer... 1.5 x .505 x .118 Bracket Deck Susp. NO.
1 532 43 99-97 2 532 19 59-68 4 532 40 30-87 5 532...
Parts Manual - Page 15
... and blade bolt/washers not included) Replacement Mower, Complete
NOTE: All component dimensions given in U.S. MODEL NUMBER YTH18542 (96043018400), PRODUCT NO. 960 43 01-84
MOWER DECK
KEY ... Gr. 5 Pulley, Idler, Flat Washer Keeper Belt Mandrel Nut, Lock Flg. 3/8-16 unc Spring Torsion Brake Spring Torsion Retainer Screw Thd Roll 1/4-20 x 5/8 Bracket Clutch Cable Arm, Idler Spacer, Retainer Screw...
Similar Questions
Do I Have To Remove The Mower Deck On My Gt52xlsi Mower In Order To Replace The
(Posted by jyahlb 2 years ago)
How Can I Get An Exploded View Of The Parte On My Yth18542?
(Posted by sleavitt1313 2 years ago)
Yth18542 Will Not Turn Over
my mower just wont do anything. I have new battery and starter solenoid. Also have new fuel filter
my mower just wont do anything. I have new battery and starter solenoid. Also have new fuel filter
(Posted by cainmccoy88 2 years ago)
Removing The Impeller
My impeller is bent and rubbing against a bolt. What is the easiest way to remove the impeller so I ...
My impeller is bent and rubbing against a bolt. What is the easiest way to remove the impeller so I ...
(Posted by Anonymous-165850 4 years ago)
Removal Of The Vacuum Tube
What is the easiest way to remove the vacuum tube from the unit???
What is the easiest way to remove the vacuum tube from the unit???
(Posted by GLB741 8 years ago)