Home » Husqvarna » Lawn Mowers » Husqvarna M-ZT 52

Husqvarna M-ZT 52 Support Question

Find answers below for this question about Husqvarna M-ZT 52.
Need a Husqvarna M-ZT 52 manual? We have 3 online manuals for this item!

Husqvarna Overview Questions Manuals Reviews Videos Research

Question posted by bamaroy on July 19th, 2016

Mower Goes Into Reverse With Levers In Neutral Position. How To Adjust?

Is there an adjustment and if so, please explain.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on July 20th, 2016 6:54 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,700

1,100
points

See http://bit.ly/29TF3Ga.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Husqvarna M-ZT 52 Manual Pages

Operation Manual - Page 3

... Fuel Shut Off Valve 21 Tracking Knob 22 Fuses 22 Cutting Height Adjuster 23 Seat Adjustment Lever 23 Hydro Release Levers 23 Refueling 24 OPERATION 25 Training 25 Steering 25 Roll Bar and...40 V-belts 40 Cutting Blades 41 Adjusting the Mower Deck 42 Leveling deck 42 Anti-scalp Rollers 43 Caster Wheels 43 Hardware 43 Cleaning 44 ZT-3400 Powertrain 44 LUBRICATION 45 Lubrication ...

Operation Manual - Page 19

... machine turns to the left. The rotation of the right wheel is moved backward behind the neutral position) and carefully moving the other . 1. The machine can turn very rapidly if one control backward (behind the neutral position. Reverse Motion control lever pattern (right side) 8065-053 19 For example, to turn can be achieved by which...

Operation Manual - Page 22

... unit by tilting the seat forward. Tracking adjustment Fuses Fuses are two fuses with both motion control levers. Back the tracking bolt out until flush with nut. 4. CONTROLS Tracking Knob If the mower is 15 psi (1 bar). 1. Drive forward at full throttle and the full forward position on the right hand side until unit...

Operation Manual - Page 23

...Adjustment Lever The seat can be adjusted while unit is in the seat). Seat adjustment Hydro Release Levers The levers are handled. See Moving Machine By Hand in the transport (highest) position. 2 1. CONTROLS Cutting Height Adjuster... in motion. Release pedal 2. The lever is used when manual pushing or pulling the unit. Right side, ZT linkage 1 8058-223 8065-125 8065...

Operation Manual - Page 25

... PRIOR to attempting to the furthest forward or reverse positions during initial operation. The left control lever controls the left wheel and cause the machine to turn in a forward direction, pull the right lever back towards the neutral position while maintaining the position of the left lever, this will allow mower to start the engine (see Moving Machine By...

Operation Manual - Page 26

...neutral position. Read the sections Safety and Controls before starting the machine. 2. Adjust the seat to lower roll bar, do not wear the seat belt. Seat adjustment...position. Before Starting 1. OPERATION Roll Bar and Safety Belt Operate the unit with the roll bar in upright position.... 4. Roll bar in the raised and locked position and use the seat belt. Set the deck cutting...

Operation Manual - Page 27

... the lift pedal fully forward. 3. Set mower deck to the transport position by pressing the blade switch down. 8058-225 5. Press the control for disengaging the mower deck 8058-043 Place controls in neutral position 8058-226 27 OPERATION Starting the Engine 1. Raise the mower deck to the transport position 4. Move the steering controls outward to the...

Operation Manual - Page 29

... Do not use the mower to the POSITIVE (+) terminal on the mower with a 12-volt ...negative grounded system. Connect each end of the fully charged battery. 3. Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the RED cable to start the engine, it should be a 12-volt negative grounded system. To remove cables, reverse...

Operation Manual - Page 30

... the seat without first setting the parking brake will shut off the engine. Make sure the work area is running, any attempt by moving the lever downward. WARNING! Engage the mower deck by the rotating blades. Move the steering controls to full throttle. 4. Move throttle control to the neutral position (N).

Operation Manual - Page 31

OPERATION Operating on Hills Read the Safety Instructions Driving on hills. • If stopping is absolutely necessary, pull drive levers into the neutral position and push to the outside of the mower and press forward to restart movement 8058-182 31 Release the parking brake to regain forward motion. • Make all turns slowly. Place...

Operation Manual - Page 32

... the transport position. 3. Raise the mower deck by pulling the lever upward. 4. Remove ignition key. Move the steering controls outward. 6. To prevent unauthorized use, always remove the key when leaving the mower. To prevent fouling the spark plugs, avoid idling the engine for longer periods. 1. IMPORTANT INFORMATION Leaving the ignition switch in neutral position to the...

Operation Manual - Page 34

... the ramps. 34 To reengage the hydro to the highest (transport) position. No adjustments or maintenance should be carried out unless: • the engine stopped • the ignition key removed • the parking brake activated 2 1 When pushing or pulling the mower, engage the bypass linkages with the head outside the bracket and held...

Operation Manual - Page 38

... be moved into the neutral position, otherwise the engine will cause premature failures. Faulty adjustment result in the seat...mower deck is on the lever, links, or switch belonging to 15 psi / 103 kPa / 1 bar. IMPORTANT INFORMATION DO NOT add any type of these conditions is equipped with a safety system that the engine stops if the mower blades are in the outer, locked neutral position...

Operation Manual - Page 42

Faulty mower deck adjustments will place the mower deck in a standard measurement position. See Technical Data / Transmission. Turn each outer blade tip to the ... your deck. Set blades to -side. 2. Slotted deck hanger plates Leveling the mower deck 8011-601 42 Leveling deck Adjust the deck while the mower is required, loosen the locknut and move mounting bolt up or down in the rear...

Operation Manual - Page 43

...Adjust anti-scalp rollers with the mower on a flat level surface. Do not adjust the rollers to the dealer for loose or missing hardware. Pull the wheel out of the ground when the deck is at the desired cutting height in the operating position... position to support the deck. The anti-scalp rollers can be adjusted to 127 mm) grass. Caster Wheels Check every 200 hours. To reInstall, reverse ...

Operation Manual - Page 50

... Problem Engine will not start Cause • Blade switch is engaged • Steering controls are not locked in the neutral position • Parking brake is not activated • Battery is dead • Contamination in the carburetor or fuel line ...) • Clogged air filter Engine seems weak • Clogged air filter • Fouled spark plugs • Carburetor incorrectly adjusted 50

Operation Manual - Page 57

...'s safety switch Check hydraulic oil level Check hydraulic hoses for kinking or leaks Check neutral position Fill with fuel and open the fuel shut off valve Start the engine Check that there is drive to both wheels Check mower deck pitch and adjustment Check: Safety switch for the parking brake Safety switch for the...

Operation Manual - Page 58

SERVICE JOURNAL Action After 10 hours Change the engine oil Change the oil filter Inspect hydraulic hoses Inspect hydraulic belt Inspect hydraulic filter Check neutral position Check safety system Check seat belt Check ROPS Check fuel system for leaks Inspect safety guards and shields Check brake adjustment Date, mtr reading, stamp, sign r r r r r r r r r r r r 58

Operation Manual - Page 61

... bearings Inspect deck belt and blades Inspect idler arm bearings Inspect deck idler pulleys Inspect hydraulic filter Inspect hydraulic drive belt Inspect hydraulic hoses Check neutral position Inspect battery connections Check safety system Check seat belt Check ROPS Check fuel system for leaks Inspect safety guards and shields Check brake...

Operation Manual - Page 62

... and blades Inspect idler arm bearings Inspect deck idler pulleys Change hydraulic oil level Change hydraulic filter Replace hydraulic drive belt Inspect hydraulic hoses Check neutral position Inspect battery connections Load test battery Clean electrical connections Inspect the clutch Check safety system Check seat belt Check ROPS Check fuel system for leaks...