Husqvarna M-ZT 52 Support Question
Husqvarna M-ZT 52 Support Question
Find answers below for this question about Husqvarna M-ZT 52.Need a Husqvarna M-ZT 52 manual? We have 3 online manuals for this item!
Question posted by wrtray54 on July 21st, 2020
Model 967177001 Hydraulic Bypass Linkage
What position should hydraulic linkage bypass be in when operating mowe
Current Answers
Answer #1: Posted by waelsaidani1 on July 21st, 2020 4:30 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
When pushing or pulling the mower, engage the bypass linkages with the hydro release levers. The levers are located on each side of the rear of the unit
below the engine plate. Raise the deck to the highest (transport) position.
Pull the bypass linkages up and out of the keyhole slots. Release the lever with the head outside the bracket and held into the bypass setting.
Related Husqvarna M-ZT 52 Manual Pages
Parts List - Page 3
CONTENTS
FRAME 4 ENGINE PLATE 6 STEERING 8 IGNITION 10 PARKING BRAKE 12 HYDRAULIC PUMP-MOTOR 14 WHEELS 16 MOWER LIFT / DECK LIFT 18 MOWER DECK / CUTTING DECK 20 SEAT 22 DECALS 24 ACCESSORIES
MULCH KIT 26
NOTE: ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED.
Parts List - Page 15
...906201 ���1 SPACER, WHEEL
15 DESCRIPTION
1.. 574 569101 1 TRANS, ZT-3400, LT 2.. 574 569102 1 TRANS, ZT-3400, RT 3.. 575 017102 1 BRACKET, TRANS, LT BLK 4.. 575 017002 1 BRACKET, TRANS, RT BLK 5.. 539 131616 1 LINKAGE, LEFT BYPASS 6.. 539 131618 1 LINKAGE, RIGHT BYPASS 7.. 574 892101 2 HOSE, EXPANSION 8.. 574 811301 2 TANK, EXPANSION 9.. 575 778202 2 COVER...
Parts List - Page 19
...6.. 539 104807 2 REINFORCEMENT BAR 7.. 539 131897 1 BELLCRANK, RR, LIFT BLK 8.. 539 131853 1 BELLCRANK, RR, RT BLK 9.. 539 112223 2 LINKAGE, STRUT 10.. 539 109693 4 LIFT CHAIN-3 LINK 11.. 539 131566 1 LATCH, TRANSPORT 12.. 539 105059 1 LANYARD 13.. 539 131791 1 MOUNT... 1 PIVOT LATCH, TRANSPORT 21.. 510 408301 1 PEDAL, FOOT
ITEM PART NO. MOWER LIFT / DECK LIFT
ITEM PART NO.
Operation Manual - Page 5
...accessible to your dealer for more information. Ensure that the machine is constructed only for mowing grass on mower.
If the machine is important for the safety of uses are provided with a ... value. The manufacturer's directions concerning operation, maintenance, and repairs must only be sure to give the operator manual to stop. Lawn mowers and all who are used improperly.
Operation Manual - Page 12
... on slopes
8011-519
Children
Tragic accidents can occur if the operator is not alert to the presence of age before operating a riding lawn mower. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. Be extra cautious when driving on the ground. • Do not mow near drop-offs, ditches, or
embankments. Never assume that children be...
Operation Manual - Page 16
... loading or unloading this machine, do not exceed the maximum recommended operation angle of suitable strength using ramps. This mower is equipped with an internal combustion engine and should not be used...when towing. Ensure that the machine is loaded on sloped ground. Escaping hydraulic oil under pressure can cause serious crushing injuries.
If a spark arrestor is used on or ...
Operation Manual - Page 20
..., pull the blade switch knob out. Release the parking brake before moving the mower. Blade switch 20
8058-182 8058-043 8058-043 On models equipped with headlights, turn the key clockwise to start the engine. The mower blades are disengaged when the knob is used to start and stop the engine. Push...
Operation Manual - Page 23
...Hand in the transport (highest) position.
2
1. Bypass linkages are located close to place the deck at the selected height.
The bypass linkage is set with the height pin. To prevent burns, the engine should not be adjusted lengthways.
Right side, ZT linkage
1
8058-223
8065-125
8065-... transport, push the lift pedal fully forward until the deck lift latches in the Operation section.
Operation Manual - Page 32
...
Disengage the mower deck and move the throttle to the minimum position (tortoise symbol). IMPORTANT INFORMATION Leaving the ignition switch in neutral position to stop position.
If the engine has been worked hard, allow it to idle a minute to transport position
5. Move the steering controls outward. 6. Remove ignition key. OPERATION
Stopping the Engine
For all models, move...
Operation Manual - Page 33
... fixed objects to side. Make sure the mower is cooled and the engine is not increased as a higher operating speed can be used , it until the desired mowing result is not too long and dense, the driving speed can be thrown out by mowing often.
The lawn becomes more even and the grass clippings more...
Operation Manual - Page 34
....
To reengage the hydro to the highest (transport) position. There is the possibility of the keyhole slots. The levers are located close to cool before the bypass linkage levels are handled.
1. WARNING! To prevent burns, the engine should be shut off the ramps.
34 OPERATION
Moving Machine By Hand
WARNING! Release lever locked into...
Operation Manual - Page 36
...-filter 2) Change the hydraulic oil (every 500 hours) Replace the hydraulic oil filter (every 500 hours) Dismantle and inspect starter 3) (every 500 hours) Check/adjust the mower deck Check the engine valve... manual ■ = Refer to OFF
position and remove the key. • Make sure the blades and all moving
parts have completely stopped.
36 When operating with a heavy load or at high ambient...
Operation Manual - Page 44
...of the deck with cold water. Let unit cool before conducting maintenance of the ZT-3400 Powertrain™ should be at the FULL COLD level. 2. Slippage can...fully.
44 Inspect the bypass mechanism on the transaxle and unit linkage to the directional control arm on the top of mower deck. MAINTENANCE
Cleaning
Regular cleaning and washing, especially under the mower deck, will increase ...
Operation Manual - Page 49
... the oil is critical to the specifications outlined above. These purge procedures should be : • Noisy operation. • Lack of oil. • Shortened component life. When the hydraulic drive operates at normal noise levels and moves smoothly forward and reverse at fast idle, slowly move the directional control in the Operation section for bypass linkage adjustments. 1.
Operation Manual - Page 51
... Bypass valve on pump open • Drive belt for the transmission gears slack or has come off • Air in hydraulic system
Mower deck not engaging
• Drive belt for the mower ... • Air trapped in hydraulic system
Uneven mowing results
•
Unequal tire pressure on the left and right sides
•
Bent blades
•
Suspension for the mower deck is uneven
•
Blades...
Operation Manual - Page 52
...the machine performs its best the following season.
52 Turn over the engine so that can occur ...especially under the mower deck. dispose of the stabilizer. Service
When ordering spare parts, please specify the purchase year, model, type, and... serial number.
An annual check-up damage to the paint and spray a thin layer of oil on the underside of the mowing...
Operation Manual - Page 57
... safety switch Check hydraulic oil level Check hydraulic hoses for kinking or leaks Check neutral position Fill with fuel and... open the fuel shut off valve Start the engine Check that there is drive to both wheels Check mower deck pitch and adjustment Check:
Safety switch for the parking brake Safety switch for the mower...
Parts Manual - Page 3
CONTENTS
FRAME 4 ENGINE PLATE 6 STEERING 8 IGNITION 10 PARKING BRAKE 12 HYDRAULIC PUMP-MOTOR 14 WHEELS 16 MOWER LIFT / DECK LIFT 18 MOWER DECK / CUTTING DECK 20 SEAT 22 DECALS 24 PROTECTION FRAME 26 ACCESSORIES
BLOWER ASSEMBLY 28 CHUTES 30 BAGGER 32 MOUNT, GUARD, BELT 34 MULCH KIT 36
NOTE: ALL FASTENERS ARE GRADE 5 UNLESS OTHERWISE SPECIFIED.
Parts Manual - Page 15
HYDRAULIC PUMP-MOTOR
ITEM PART NO. DESCRIPTION
1.. 574 569101 1 TRANS, ZT-3400, LT 2.. 574 569102 1 TRANS, ZT-3400, RT 3.. 575 017102 1 BRACKET, TRANS, LT BLK 4.. 575 017002 1 BRACKET, TRANS, RT BLK 5.. 539 131616 1 LINKAGE, LEFT BYPASS 6.. 539 131618 1 LINKAGE, RIGHT BYPASS 7.. 574 892101 2 HOSE, EXPANSION 8.. 574 811301 2 TANK, EXPANSION 9.. 575 778202 2 COVER, FAN 10.. ...
Parts Manual - Page 19
... 539 131897 1 BELLCRANK, RR, LIFT BLK 8.. 539 131853 1 BELLCRANK, RR, RT BLK 9.. 539 112223 2 LINKAGE, STRUT 10.. 539 109693 4 LIFT CHAIN-3 LINK 11.. 539 131566 1 LATCH, TRANSPORT 12.. 539 105059 1 LANYARD... 20.. 539 131860 1 PIVOT LATCH, TRANSPORT 21.. 510 408301 1 PEDAL, FOOT
ITEM PART NO. MOWER LIFT / DECK LIFT
ITEM PART NO. QTY. QTY. DESCRIPTION
22.. 539 132182 1 PIN ½...
Similar Questions
Zero Turn Mower Quit Moving Forward Or Backwards
Our Husquavarna MZT 52 quit moving while we were cutting grass. It won't go forward or backwards.
Our Husquavarna MZT 52 quit moving while we were cutting grass. It won't go forward or backwards.
(Posted by dawracer75 4 years ago)
Mower Goes Into Reverse With Levers In Neutral Position. How To Adjust?
Is there an adjustment and if so, please explain.
Is there an adjustment and if so, please explain.
(Posted by bamaroy 7 years ago)
My Husqvarnarz4623 Lawn Mower
My husqvarna lawn mower will not start. It wont even try to turn over or click.
My husqvarna lawn mower will not start. It wont even try to turn over or click.
(Posted by teresaandbryancates 9 years ago)