Hoover U6634900 Support Question
Hoover U6634900 Support Question
Find answers below for this question about Hoover U6634900 - Self Propelled WindTunnel Bagless Upright Vacuum.Need a Hoover U6634900 manual? We have 1 online manual for this item!
Question posted by goldiestevens on April 1st, 2014
I Changed Belts But Suction Isn't Working
The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hoover U6634900 Manual Pages
Manual - Page 1
Self-Propelled WindTunnel™ Bagless with Powered Hand Tool by HOOVER
®
This product was designed for easy Assembly (See page 3)
www.hoover.com
Manual - Page 2
...3 Carton Contents 3
How To Use Cleaner Descriptions 4 Cleaning Tools 6-7 Embedded Dirt FINDERTM Feature .5 Upright Cleaner 4-6 Self-Propel Feature 4
Important Safeguards 2 Maintenance
Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand Tool Agitator Brush Roll...
Manual - Page 3
... into back of lock. If you should happen to find the service outlet nearest you (click on front of handle. Make sure all parts from self-propel button. Handle section B. Powered hand tool
*some models include an extra hose
Note: The white switch lock above ONOFF switch (C) on the "Service" button) OR...
Manual - Page 4
... posi- 28.
Guide cleaner carefully at voltage specified on data plate on rear wheels and push forward.
Self-propel button
17. Furniture nozzle 8. Carrying handle
pedal to lower handle to deactivate the feature. Do not change the plug in tight places (e.g., around hooks for easy cord
15. This cleaner is wider than the...
Manual - Page 5
... "Reg." (Regular) position.
2-9
FLOOR
CARPET
HARD
Brush roll control
Note: When handle is in upright position, brush roll is able to turn brush roll OFF when cleaning bare floors. Slide control to ...of carpet • Higher settings: for cleaning carpet or rugs.
B
Carpet height adjustment
When it changes to the desired setting. After a few seconds, the red light will go off and the ...
Manual - Page 6
... second wand or tool to cleaner. Before reaching edge, push down on handle.
Cleaning tools
When using cleaning tools, cleaner handle must be in the upright position to activate the automatic "brush roll OFF" and for stair cleaning.
Twist wand or tool slightly to hose tube (E). Clean from falling, always place...
Manual - Page 7
...tools
To clean the hose and the powered hand tool, wipe off dirt with slots on end of suction. Use them with a damp cloth.
To reattach, align hinges of dirt cup (Fig. 3-1) or... to empty
It is recommended that have passed through the pre-filter screen. Slide latch (F) to your vacuum cleaner, follow the instructions below.
2-18
M N
Turn cleaner OFF before the dirt reaches the dirt ...
Manual - Page 8
...: It is pushed open too far. To reattach, align hinges of lid with water. Filter assembly
The HEPA cartridge filter and pre-filter are essentially self-shedding. The HEPA cartridge filter can also be cleaned with a brush and then rinsed with slots in place.
The filter assembly can be cleaned by...
Manual - Page 9
... secure with a "break-away" feature which allows it becomes dirty, open too far.
To replace this debris will help maintain your cleaner picks up and suction.
Headlight replacement
What to the brush roll when you want to cleaner (Fig. 3-5). Note: If dirt cup lid does not close all the way. Make...
Manual - Page 10
....
Brush roll can start suddenly. Unplug cleaner when it is stretched, cut or broken. Remove used belt Flat belt (B) operates the self-propel feature and indirectly drives the brush roll.
Positioning back of belt
With lettering on outside of belt Place other is described below;
The agitator brush roll
When to replace
Disconnect cleaner from electrical...
Manual - Page 11
... "snap" it as follows. Turn cleaner over pulley (C). Then firmly pull on either side of cleaner.
However, if V-belt is cracked, gouged or broken, now is not normally replaced. E C
Inspecting V-belt
The V-belt is designed to last for a long time and is a good time to pulley. Remove tool from hose and turn it...
Manual - Page 12
... front of brush roll into place. 5. Pivot bottom plate down , slide retainers into grooves (H) in good condition.
Remove agitator including end plates (C) and discard.
4. Inspect belt to pinch brush bristles in guard. Turn agitator, making sure not to ensure that it is cracked, gouged or broken, replace it should be seen...
Manual - Page 13
... thermal protector activates, the cleaner will only result in "The belt" section (Fig.3-18).
3-37
Installing groomers Lift off both...identify your cleaner by :
• checking the Yellow Pages under "Vacuum Cleaners -
In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8...(The model number appears on the bottom of Hoover uprights only and not for comparison with this rating is ...
Manual - Page 14
... Problem: Powered hand tool brush roll won 't self-propel
Possible cause
Possible solution • Flat belt broken or worn • Replace belt. • Self-propel button in the system.
Unplug cleaner when it... blockages
Disconnect cleaner from hose. Low suction or pick up Possible cause
Possible solution 14
• Cleaner handle not in upright position
• Ensure that entire filter...
Similar Questions
How To Change Belt For Power Nozzle?
How to change belt for power nozzle?
How to change belt for power nozzle?
(Posted by Missionnews777 1 year ago)
Hoover Windtunnel Anniversary Upright Vacuum, Self-propelled, Bagged, U6485900
won't shut off
won't shut off
(Posted by patciam 9 years ago)
Very Little Suction
Vacuum has very little suction. Hose is not plugged. Filter is clean. Could gaskets on the removable...
Vacuum has very little suction. Hose is not plugged. Filter is clean. Could gaskets on the removable...
(Posted by kwlaursen 10 years ago)